mirror of
https://github.com/alexhopeoconnor/arduino-home-assistant.git
synced 2026-10-04 02:48:13 +10:00
Dawid Chyrzyński
87b7e03fe6
* added support for setting None value in the HASensor * added support for the expire_after property in the HASensor * update readme and docs * added expire_after property in the HABinarySensor * increase default device types limit to 24 on non ATMega328/168 processors * added support for the JSON attributes in the HASensor
71 lines
2.4 KiB
Arduino
71 lines
2.4 KiB
Arduino
#include <Ethernet.h>
|
|
#include <ArduinoHA.h>
|
|
|
|
#define BROKER_ADDR IPAddress(192,168,0,17)
|
|
|
|
byte mac[] = {0x00, 0x10, 0xFA, 0x6E, 0x38, 0x4A};
|
|
|
|
EthernetClient client;
|
|
HADevice device(mac, sizeof(mac));
|
|
HAMqtt mqtt(client, device);
|
|
|
|
// "myCover" is unique ID of the cover. You should define your own ID.
|
|
HACover cover("myCover", HACover::PositionFeature);
|
|
|
|
// PositionFeature is optional, however required to be in a "stopped" state other than open or closed.
|
|
// If ommitted, a CommandStop will result in HA treating the cover as either Open or Closed immediately after the command.
|
|
// See https://www.home-assistant.io/integrations/cover.mqtt/
|
|
// Added in https://github.com/dawidchyrzynski/arduino-home-assistant/pull/111
|
|
|
|
void onCoverCommand(HACover::CoverCommand cmd, HACover* sender) {
|
|
if (cmd == HACover::CommandOpen) {
|
|
Serial.println("Command: Open");
|
|
sender->setState(HACover::StateOpening); // report state back to the HA
|
|
} else if (cmd == HACover::CommandClose) {
|
|
Serial.println("Command: Close");
|
|
sender->setState(HACover::StateClosing); // report state back to the HA
|
|
} else if (cmd == HACover::CommandStop) {
|
|
Serial.println("Command: Stop");
|
|
sender->setState(HACover::StateStopped); // report state back to the HA
|
|
}
|
|
|
|
// Available states:
|
|
// HACover::StateClosed
|
|
// HACover::StateClosing
|
|
// HACover::StateOpen
|
|
// HACover::StateOpening
|
|
// HACover::StateStopped
|
|
|
|
// You can also report position using setPosition() method
|
|
}
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
Ethernet.begin(mac);
|
|
|
|
// optional device's details
|
|
device.setName("Arduino");
|
|
device.setSoftwareVersion("1.0.0");
|
|
|
|
cover.onCommand(onCoverCommand);
|
|
cover.setName("My cover"); // optional
|
|
|
|
// Optionally you can set retain flag for the HA commands
|
|
// cover.setRetain(true);
|
|
|
|
// Optionally you can enable optimistic mode for the HACover.
|
|
// In this mode you won't need to report state back to the HA when commands are executed.
|
|
// cover.setOptimistic(true);
|
|
|
|
mqtt.begin(BROKER_ADDR);
|
|
}
|
|
|
|
void loop() {
|
|
Ethernet.maintain();
|
|
mqtt.loop();
|
|
|
|
// You can also change the state at runtime as shown below.
|
|
// This kind of logic can be used if you want to control your cover using a button connected to the device.
|
|
// cover.setState(HACover::StateOpening); // use any state you want
|
|
}
|