mirror of
https://github.com/alexhopeoconnor/firmware.git
synced 2026-10-20 02:11:28 +10:00
Merge branch 'master' into arduino-esp32-v3.2
This commit is contained in:
Manuel
@@ -0,0 +1,12 @@
|
||||
; 9M2IBR APRS LoRa Tracker: ESP32-WROOM-32 + EBYTE E22-400M30S
|
||||
; https://shopee.com.my/product/1095224/21692283917
|
||||
[env:9m2ibr_aprs_lora_tracker]
|
||||
extends = esp32_base
|
||||
board = esp32doit-devkit-v1
|
||||
board_level = extra
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D PRIVATE_HW
|
||||
-D EBYTE_E22
|
||||
-D EBYTE_E22_900M30S ; Assume Tx power curve is identical to 900M30S as there is no documentation
|
||||
-I variants/esp32/diy/9m2ibr_aprs_lora_tracker
|
||||
@@ -0,0 +1,74 @@
|
||||
/*
|
||||
|
||||
9M2IBR APRS LoRa Tracker: ESP32-WROOM-32 + EBYTE E22-400M30S
|
||||
https://shopee.com.my/product/1095224/21692283917
|
||||
|
||||
Originally developed for LoRa_APRS_iGate and GPIO is similar to
|
||||
https://github.com/richonguzman/LoRa_APRS_iGate/blob/main/variants/ESP32_DIY_1W_LoRa_Mesh_V1_2/board_pinout.h
|
||||
|
||||
*/
|
||||
|
||||
// OLED (may be different controllers depending on screen size)
|
||||
#define I2C_SDA 21
|
||||
#define I2C_SCL 22
|
||||
#define HAS_SCREEN 1 // Generates randomized BLE pin
|
||||
|
||||
// GNSS: Ai-Thinker GP-02 BDS/GNSS module
|
||||
#define GPS_RX_PIN 16
|
||||
#define GPS_TX_PIN 17
|
||||
|
||||
// Button
|
||||
#define BUTTON_PIN 15 // Right side button - if not available, set device.button_gpio to 0 from Meshtastic client
|
||||
|
||||
// LEDs
|
||||
#define LED_PIN 13 // Tx LED
|
||||
#define USER_LED 2 // Rx LED
|
||||
|
||||
// Buzzer
|
||||
#define PIN_BUZZER 33
|
||||
|
||||
// Battery sense
|
||||
#define BATTERY_PIN 35
|
||||
#define ADC_MULTIPLIER 2.01 // 100k + 100k, and add 1% tolerance
|
||||
#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS ADC_RESOLUTION
|
||||
|
||||
// SPI
|
||||
#define LORA_SCK 18
|
||||
#define LORA_MISO 19
|
||||
#define LORA_MOSI 23
|
||||
|
||||
// LoRa
|
||||
#define LORA_CS 5
|
||||
#define LORA_DIO0 26 // a No connect on the SX1262/SX1268 module
|
||||
#define LORA_RESET 27 // RST for SX1276, and for SX1262/SX1268
|
||||
#define LORA_DIO1 12 // IRQ for SX1262/SX1268
|
||||
#define LORA_DIO2 RADIOLIB_NC // BUSY for SX1262/SX1268
|
||||
#define LORA_DIO3 // NC, but used as TCXO supply by E22 module
|
||||
#define LORA_RXEN 32 // RF switch RX (and E22 LNA) control by ESP32 GPIO
|
||||
#define LORA_TXEN 25 // RF switch TX (and E22 PA) control by ESP32 GPIO
|
||||
|
||||
// RX/TX for RFM95/SX127x
|
||||
#define RF95_RXEN LORA_RXEN
|
||||
#define RF95_TXEN LORA_TXEN
|
||||
// #define RF95_TCXO <GPIO#>
|
||||
|
||||
// common pinouts for SX126X modules
|
||||
#define SX126X_CS 5
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_BUSY LORA_DIO2
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_RXEN LORA_RXEN
|
||||
#define SX126X_TXEN LORA_TXEN
|
||||
|
||||
// Support alternative modules if soldered in place of E22
|
||||
#define USE_RF95 // RFM95/SX127x
|
||||
#define USE_SX1262
|
||||
#define USE_SX1268
|
||||
#define USE_LLCC68
|
||||
|
||||
// E22 TCXO support
|
||||
#ifdef EBYTE_E22
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#define TCXO_OPTIONAL // make it so that the firmware can try both TCXO and XTAL
|
||||
#endif
|
||||
@@ -1,6 +1,7 @@
|
||||
[env:heltec-wireless-bridge]
|
||||
;build_type = debug ; to make it possible to step through our jtag debugger
|
||||
extends = esp32_base
|
||||
board_level = extra
|
||||
board = heltec_wifi_lora_32
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
|
||||
@@ -1,5 +1,6 @@
|
||||
[env:trackerd]
|
||||
extends = esp32_base
|
||||
board_level = extra
|
||||
board = pico32
|
||||
board_build.f_flash = 80000000L
|
||||
|
||||
|
||||
@@ -61,7 +61,7 @@
|
||||
#define LORA_DIO1 SX126X_DIO1
|
||||
|
||||
#define USE_EINK
|
||||
#define PIN_EINK_EN -1 // Note: this is really just backlight power
|
||||
// Note: this is really just backlight power
|
||||
#define PCA_PIN_EINK_EN 5 // This is the pin number on the GPIO expander
|
||||
#define PIN_EINK_CS 39
|
||||
#define PIN_EINK_BUSY 42
|
||||
|
||||
@@ -19,8 +19,6 @@ build_flags = ${esp32s3_base.build_flags} -Os
|
||||
-D MESHTASTIC_EXCLUDE_SERIAL=1
|
||||
-D MESHTASTIC_EXCLUDE_SOCKETAPI=1
|
||||
-D MESHTASTIC_EXCLUDE_SCREEN=1
|
||||
-D MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
|
||||
-D HAS_TELEMETRY=0
|
||||
-D CONFIG_DISABLE_HAL_LOCKS=1
|
||||
-D USE_PIN_BUZZER
|
||||
-D HAS_SCREEN=0
|
||||
|
||||
@@ -0,0 +1,28 @@
|
||||
#ifndef Pins_Arduino_h
|
||||
#define Pins_Arduino_h
|
||||
|
||||
#include "variant.h"
|
||||
#include <stdint.h>
|
||||
|
||||
#define USB_VID 0x303a
|
||||
#define USB_PID 0x1001
|
||||
|
||||
// The default Wire will be mapped to PMU and RTC
|
||||
static const uint8_t SDA = 9;
|
||||
static const uint8_t SCL = 40;
|
||||
|
||||
// Default SPI will be mapped to Radio
|
||||
static const uint8_t SS = 12;
|
||||
static const uint8_t MOSI = 11;
|
||||
static const uint8_t MISO = 10;
|
||||
static const uint8_t SCK = 13;
|
||||
|
||||
#define SPI_MOSI (11)
|
||||
#define SPI_SCK (13)
|
||||
#define SPI_MISO (10)
|
||||
#define SPI_CS (12)
|
||||
|
||||
// LEDs
|
||||
#define LED_BUILTIN LED_GREEN
|
||||
|
||||
#endif /* Pins_Arduino_h */
|
||||
@@ -0,0 +1,87 @@
|
||||
; rak_wismeshtap2 rak3112
|
||||
|
||||
[rak_wismeshtap_s3]
|
||||
extends = esp32s3_base
|
||||
board = wiscore_rak3312
|
||||
board_check = true
|
||||
upload_protocol = esptool
|
||||
board_build.partitions = default_8MB.csv
|
||||
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D RAK3312
|
||||
-D RAK_WISMESH_TAP_V2
|
||||
-I variants/esp32s3/rak_wismesh_tap_v2
|
||||
|
||||
lib_deps =
|
||||
${esp32s3_base.lib_deps}
|
||||
lovyan03/LovyanGFX@^1.2.0
|
||||
|
||||
[ft5x06]
|
||||
extends = mesh_tab_base
|
||||
build_flags =
|
||||
-D LGFX_TOUCH=FT5x06
|
||||
-D LGFX_TOUCH_I2C_FREQ=100000
|
||||
-D LGFX_TOUCH_I2C_PORT=0
|
||||
-D LGFX_TOUCH_I2C_ADDR=0x38
|
||||
-D LGFX_TOUCH_I2C_SDA=9
|
||||
-D LGFX_TOUCH_I2C_SCL=40
|
||||
-D LGFX_TOUCH_RST=-1
|
||||
-D LGFX_TOUCH_INT=39
|
||||
|
||||
[env:rak_wismesh_tap_v2-tft]
|
||||
extends = rak_wismeshtap_s3
|
||||
|
||||
build_flags =
|
||||
${rak_wismeshtap_s3.build_flags}
|
||||
-D CONFIG_ARDUHAL_ESP_LOG
|
||||
-D CONFIG_ARDUHAL_LOG_COLORS=1
|
||||
-D CONFIG_DISABLE_HAL_LOCKS=1
|
||||
-D LV_LVGL_H_INCLUDE_SIMPLE
|
||||
-D LV_CONF_INCLUDE_SIMPLE
|
||||
-D LV_COMP_CONF_INCLUDE_SIMPLE
|
||||
-D LV_USE_SYSMON=0
|
||||
-D LV_USE_PROFILER=0
|
||||
-D LV_USE_PERF_MONITOR=0
|
||||
-D LV_USE_MEM_MONITOR=0
|
||||
-D LV_USE_LOG=0
|
||||
-D LV_BUILD_TEST=0
|
||||
-D USE_LOG_DEBUG
|
||||
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
|
||||
-D RADIOLIB_SPI_PARANOID=0
|
||||
-D INPUTDRIVER_BUTTON_TYPE=0
|
||||
-D HAS_SDCARD
|
||||
-D HAS_SCREEN=0
|
||||
-D HAS_TFT=1
|
||||
-D USE_PIN_BUZZER=PIN_BUZZER
|
||||
-D RAM_SIZE=5120
|
||||
-D LGFX_DRIVER_TEMPLATE
|
||||
-D LGFX_DRIVER=LGFX_GENERIC
|
||||
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
|
||||
-D LGFX_PIN_SCK=13
|
||||
-D LGFX_PIN_MOSI=11
|
||||
-D LGFX_PIN_MISO=10
|
||||
-D LGFX_PIN_DC=42
|
||||
-D LGFX_PIN_CS=12
|
||||
-D LGFX_PIN_RST=-1
|
||||
-D LGFX_PIN_BL=41
|
||||
-D VIEW_320x240
|
||||
-D USE_PACKET_API
|
||||
${ft5x06.build_flags}
|
||||
-D LGFX_SCREEN_WIDTH=240
|
||||
-D LGFX_SCREEN_HEIGHT=320
|
||||
-D LGFX_PANEL=ST7789
|
||||
-D LGFX_ROTATION=1
|
||||
-D LGFX_TOUCH_X_MIN=0
|
||||
-D LGFX_TOUCH_X_MAX=239
|
||||
-D LGFX_TOUCH_Y_MIN=0
|
||||
-D LGFX_TOUCH_Y_MAX=319
|
||||
-D LGFX_TOUCH_ROTATION=2
|
||||
-D LGFX_CFG_HOST=SPI3_HOST
|
||||
-D MAP_FULL_REDRAW=1
|
||||
|
||||
lib_deps =
|
||||
${rak_wismeshtap_s3.lib_deps}
|
||||
${device-ui_base.lib_deps}
|
||||
|
||||
|
||||
@@ -0,0 +1,71 @@
|
||||
#ifndef _VARIANT_RAK_WISMESHTAP_V2_H
|
||||
#define _VARIANT_RAK_WISMESHTAP_V2_H
|
||||
|
||||
#define I2C_SDA 9
|
||||
#define I2C_SCL 40
|
||||
|
||||
#define USE_SX1262
|
||||
|
||||
#define LORA_SCK 5
|
||||
#define LORA_MISO 3
|
||||
#define LORA_MOSI 6
|
||||
#define LORA_CS 7
|
||||
#define LORA_RESET 8
|
||||
|
||||
#ifdef USE_SX1262
|
||||
#define SX126X_CS LORA_CS
|
||||
#define SX126X_DIO1 47
|
||||
#define SX126X_BUSY 48
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#endif
|
||||
|
||||
#define SX126X_POWER_EN (4)
|
||||
|
||||
#define PIN_POWER_EN PIN_3V3_EN
|
||||
#define PIN_3V3_EN (14)
|
||||
|
||||
#define LED_GREEN 46
|
||||
#define LED_BLUE 45
|
||||
|
||||
#define PIN_LED1 LED_GREEN
|
||||
#define PIN_LED2 LED_BLUE
|
||||
|
||||
#define LED_CONN LED_BLUE
|
||||
#define LED_PIN LED_GREEN
|
||||
#define ledOff(pin) pinMode(pin, INPUT)
|
||||
|
||||
#define LED_STATE_ON 1 // State when LED is litted
|
||||
|
||||
#define HAS_GPS 1
|
||||
#define GPS_TX_PIN 43
|
||||
#define GPS_RX_PIN 44
|
||||
|
||||
#define SPI_MOSI (11)
|
||||
#define SPI_SCK (13)
|
||||
#define SPI_MISO (10)
|
||||
#define SPI_CS (12)
|
||||
|
||||
#define HAS_BUTTON 1
|
||||
#define BUTTON_PIN 0
|
||||
|
||||
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||||
#define USE_VIRTUAL_KEYBOARD 1
|
||||
|
||||
#define BATTERY_PIN 1
|
||||
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
|
||||
#define ADC_MULTIPLIER 1.667
|
||||
|
||||
#define PIN_BUZZER 38
|
||||
|
||||
#define HAS_SDCARD 1
|
||||
#define SDCARD_USE_SPI1 1
|
||||
#define SDCARD_CS 2
|
||||
|
||||
#define SPI_FREQUENCY 40000000
|
||||
#define SPI_READ_FREQUENCY 16000000
|
||||
|
||||
#define SD_SPI_FREQUENCY 50000000
|
||||
|
||||
#endif
|
||||
@@ -92,3 +92,12 @@
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 2.4
|
||||
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
|
||||
// code)
|
||||
|
||||
#define MODEM_POWER_EN 41
|
||||
#define MODEM_PWRKEY 40
|
||||
#define MODEM_RST 9
|
||||
#define MODEM_RI 7
|
||||
#define MODEM_DTR 8
|
||||
#define MODEM_RX 10
|
||||
#define MODEM_TX 11
|
||||
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
#ifndef Pins_Arduino_h
|
||||
#define Pins_Arduino_h
|
||||
|
||||
#include <stdint.h>
|
||||
|
||||
#define USB_VID 0x303a
|
||||
#define USB_PID 0x1001
|
||||
|
||||
// used for keyboard, battery gauge, charger and haptic driver
|
||||
static const uint8_t SDA = 3;
|
||||
static const uint8_t SCL = 2;
|
||||
|
||||
// Default SPI will be mapped to Radio
|
||||
static const uint8_t SS = 36;
|
||||
static const uint8_t MOSI = 34;
|
||||
static const uint8_t MISO = 33;
|
||||
static const uint8_t SCK = 35;
|
||||
|
||||
#endif /* Pins_Arduino_h */
|
||||
@@ -0,0 +1,71 @@
|
||||
; LilyGo T-Lora-Pager
|
||||
[env:tlora-pager]
|
||||
extends = esp32s3_base
|
||||
board = t-deck-pro ; same as T-Deck Pro
|
||||
board_check = true
|
||||
board_build.partitions = default_16MB.csv
|
||||
upload_protocol = esptool
|
||||
|
||||
build_flags = ${esp32s3_base.build_flags}
|
||||
-I variants/esp32s3/tlora-pager
|
||||
-D T_LORA_PAGER
|
||||
-D BOARD_HAS_PSRAM
|
||||
-D GPS_POWER_TOGGLE
|
||||
-D HAS_SDCARD
|
||||
-D SDCARD_USE_SPI1
|
||||
-D ENABLE_ROTARY_PULLUP
|
||||
-D ENABLE_BUTTON_PULLUP
|
||||
-D HALF_STEP
|
||||
|
||||
lib_deps = ${esp32s3_base.lib_deps}
|
||||
lovyan03/LovyanGFX@1.2.7
|
||||
earlephilhower/ESP8266Audio@1.9.9
|
||||
earlephilhower/ESP8266SAM@1.0.1
|
||||
adafruit/Adafruit DRV2605 Library@1.2.4
|
||||
lewisxhe/PCF8563_Library@1.0.1
|
||||
lewisxhe/SensorLib@0.3.1
|
||||
https://github.com/pschatzmann/arduino-audio-driver/archive/refs/tags/v0.1.3.zip
|
||||
https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip
|
||||
https://github.com/mverch67/RotaryEncoder/archive/25a59d5745a6645536f921427d80b08e78f886d4.zip
|
||||
|
||||
[env:tlora-pager-tft]
|
||||
board_level = extra
|
||||
extends = env:tlora-pager
|
||||
build_flags =
|
||||
${env:tlora-pager.build_flags}
|
||||
-D CONFIG_DISABLE_HAL_LOCKS=1
|
||||
-D INPUTDRIVER_ROTARY_TYPE=1
|
||||
-D INPUTDRIVER_ROTARY_UP=40
|
||||
-D INPUTDRIVER_ROTARY_DOWN=41
|
||||
-D INPUTDRIVER_ROTARY_BTN=7
|
||||
-D INPUTDRIVER_BUTTON_TYPE=0
|
||||
-D HAS_SCREEN=1
|
||||
-D HAS_TFT=1
|
||||
-D USE_I2S_BUZZER
|
||||
-D RAM_SIZE=5120
|
||||
-D LV_LVGL_H_INCLUDE_SIMPLE
|
||||
-D LV_CONF_INCLUDE_SIMPLE
|
||||
-D LV_COMP_CONF_INCLUDE_SIMPLE
|
||||
-D LV_USE_SYSMON=0
|
||||
-D LV_USE_PROFILER=0
|
||||
-D LV_USE_PERF_MONITOR=0
|
||||
-D LV_USE_MEM_MONITOR=0
|
||||
-D LV_USE_LOG=0
|
||||
-D USE_LOG_DEBUG
|
||||
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
|
||||
-D RADIOLIB_SPI_PARANOID=0
|
||||
-D LGFX_SCREEN_WIDTH=222
|
||||
-D LGFX_SCREEN_HEIGHT=480
|
||||
-D DISPLAY_SIZE=480x222 ; landscape mode
|
||||
-D DISPLAY_SET_RESOLUTION
|
||||
-D LGFX_DRIVER=LGFX_TLORA_PAGER
|
||||
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_T_LORA_PAGER.h\"
|
||||
; -D LVGL_DRIVER=LVGL_T_LORA_PAGER
|
||||
; -D LV_USE_ST7796=1
|
||||
-D VIEW_480x222
|
||||
-D USE_PACKET_API
|
||||
-D MAP_FULL_REDRAW
|
||||
|
||||
lib_deps =
|
||||
${env:tlora-pager.lib_deps}
|
||||
${device-ui_base.lib_deps}
|
||||
@@ -0,0 +1,125 @@
|
||||
// ST7796 TFT LCD
|
||||
#define TFT_CS 38
|
||||
#define ST7796_CS TFT_CS
|
||||
#define ST7796_RS 37 // DC
|
||||
#define ST7796_SDA MOSI // MOSI
|
||||
#define ST7796_SCK SCK
|
||||
#define ST7796_RESET -1
|
||||
#define ST7796_MISO MISO
|
||||
#define ST7796_BUSY -1
|
||||
#define ST7796_BL 42
|
||||
#define ST7796_SPI_HOST SPI2_HOST
|
||||
#define TFT_BL 42
|
||||
#define SPI_FREQUENCY 75000000
|
||||
#define SPI_READ_FREQUENCY 16000000
|
||||
#define TFT_HEIGHT 480
|
||||
#define TFT_WIDTH 222
|
||||
#define TFT_OFFSET_X 49
|
||||
#define TFT_OFFSET_Y 0
|
||||
#define TFT_OFFSET_ROTATION 3
|
||||
#define SCREEN_ROTATE
|
||||
#define SCREEN_TRANSITION_FRAMERATE 5
|
||||
#define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
|
||||
|
||||
#define I2C_SDA SDA
|
||||
#define I2C_SCL SCL
|
||||
|
||||
#define USE_POWERSAVE
|
||||
#define SLEEP_TIME 120
|
||||
|
||||
// GNNS
|
||||
#define HAS_GPS 1
|
||||
#define GPS_BAUDRATE 38400
|
||||
#define GPS_RX_PIN 4
|
||||
#define GPS_TX_PIN 12
|
||||
#define PIN_GPS_PPS 13
|
||||
|
||||
// PCF8563 RTC Module
|
||||
#if __has_include("pcf8563.h")
|
||||
#include "pcf8563.h"
|
||||
#endif
|
||||
#define PCF8563_RTC 0x51
|
||||
#define HAS_RTC 1
|
||||
|
||||
// Rotary
|
||||
#define ROTARY_A (40)
|
||||
#define ROTARY_B (41)
|
||||
#define ROTARY_PRESS (7)
|
||||
|
||||
#define BUTTON_PIN 0
|
||||
|
||||
// SPI interface SD card slot
|
||||
#define SPI_MOSI MOSI
|
||||
#define SPI_SCK SCK
|
||||
#define SPI_MISO MISO
|
||||
#define SPI_CS 21
|
||||
#define SDCARD_CS SPI_CS
|
||||
#define SD_SPI_FREQUENCY 75000000U
|
||||
|
||||
// TCA8418 keyboard
|
||||
#define I2C_NO_RESCAN
|
||||
#define KB_BL_PIN 46
|
||||
#define KB_INT 6
|
||||
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||||
|
||||
// audio codec ES8311
|
||||
#define HAS_I2S
|
||||
#define DAC_I2S_BCK 11
|
||||
#define DAC_I2S_WS 18
|
||||
#define DAC_I2S_DOUT 45
|
||||
#define DAC_I2S_DIN 17
|
||||
#define DAC_I2S_MCLK 10
|
||||
|
||||
// gyroscope BHI260AP
|
||||
#define HAS_BHI260AP
|
||||
|
||||
// battery charger BQ25896
|
||||
#define HAS_PPM 1
|
||||
#define XPOWERS_CHIP_BQ25896
|
||||
|
||||
// battery quality management BQ27220
|
||||
#define HAS_BQ27220 1
|
||||
#define BQ27220_I2C_SDA SDA
|
||||
#define BQ27220_I2C_SCL SCL
|
||||
#define BQ27220_DESIGN_CAPACITY 1500
|
||||
|
||||
// NFC ST25R3916
|
||||
#define NFC_INT 5
|
||||
#define NFC_CS 39
|
||||
|
||||
// External expansion chip XL9555
|
||||
#define USE_XL9555
|
||||
#define EXPANDS_DRV_EN (0)
|
||||
#define EXPANDS_AMP_EN (1)
|
||||
#define EXPANDS_KB_RST (2)
|
||||
#define EXPANDS_LORA_EN (3)
|
||||
#define EXPANDS_GPS_EN (4)
|
||||
#define EXPANDS_NFC_EN (5)
|
||||
#define EXPANDS_GPS_RST (7)
|
||||
#define EXPANDS_KB_EN (8)
|
||||
#define EXPANDS_GPIO_EN (9)
|
||||
#define EXPANDS_SD_DET (10)
|
||||
#define EXPANDS_SD_PULLEN (11)
|
||||
#define EXPANDS_SD_EN (12)
|
||||
|
||||
// LoRa
|
||||
#define USE_SX1262
|
||||
#define USE_SX1268
|
||||
|
||||
#define LORA_SCK 35
|
||||
#define LORA_MISO 33
|
||||
#define LORA_MOSI 34
|
||||
#define LORA_CS 36
|
||||
|
||||
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
||||
#define LORA_RESET 47
|
||||
#define LORA_DIO1 14 // SX1262 IRQ
|
||||
#define LORA_DIO2 48 // SX1262 BUSY
|
||||
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
||||
|
||||
#define SX126X_CS LORA_CS
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_BUSY LORA_DIO2
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 3.0
|
||||
@@ -32,6 +32,7 @@ lib_deps = ${esp32s3_base.lib_deps}
|
||||
|
||||
|
||||
[env:unphone-tft]
|
||||
board_level = extra
|
||||
extends = env:unphone
|
||||
build_flags =
|
||||
${env:unphone.build_flags}
|
||||
@@ -52,8 +53,6 @@ build_flags =
|
||||
-D LV_USE_PERF_MONITOR=0
|
||||
-D LV_USE_MEM_MONITOR=0
|
||||
-D LV_USE_LOG=0
|
||||
-D USE_LOG_DEBUG
|
||||
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
|
||||
-D LGFX_SCREEN_WIDTH=320
|
||||
-D LGFX_SCREEN_HEIGHT=480
|
||||
-D DISPLAY_SIZE=320x480 ; portrait mode
|
||||
|
||||
@@ -1,10 +1,12 @@
|
||||
[native_base]
|
||||
extends = portduino_base
|
||||
build_flags = ${portduino_base.build_flags} -I variants/native/portduino
|
||||
-D ARCH_PORTDUINO
|
||||
-I /usr/include
|
||||
board = cross_platform
|
||||
lib_deps = ${portduino_base.lib_deps}
|
||||
lib_deps =
|
||||
${portduino_base.lib_deps}
|
||||
melopero/Melopero RV3028@^1.1.0
|
||||
|
||||
build_src_filter = ${portduino_base.build_src_filter}
|
||||
|
||||
[env:native]
|
||||
@@ -26,7 +28,6 @@ build_flags = ${native_base.build_flags} -Os -lX11 -linput -lxkbcommon -ffunctio
|
||||
-D USE_X11=1
|
||||
-D HAS_TFT=1
|
||||
-D HAS_SCREEN=1
|
||||
|
||||
-D LV_CACHE_DEF_SIZE=6291456
|
||||
-D LV_BUILD_TEST=0
|
||||
-D LV_USE_LIBINPUT=1
|
||||
@@ -42,6 +43,25 @@ build_flags = ${native_base.build_flags} -Os -lX11 -linput -lxkbcommon -ffunctio
|
||||
build_src_filter =
|
||||
${native_base.build_src_filter}
|
||||
|
||||
[env:native-sdl]
|
||||
extends = native_base
|
||||
build_type = release
|
||||
lib_deps =
|
||||
${env.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
${radiolib_base.lib_deps}
|
||||
${environmental_base.lib_deps}
|
||||
# renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
|
||||
rweather/Crypto@0.4.0
|
||||
# renovate: datasource=git-refs depName=libch341-spi-userspace packageName=https://github.com/pine64/libch341-spi-userspace gitBranch=main
|
||||
https://github.com/pine64/libch341-spi-userspace/archive/af9bc27c9c30fa90772279925b7c5913dff789b4.zip
|
||||
# renovate: datasource=custom.pio depName=adafruit/Adafruit seesaw Library packageName=adafruit/library/Adafruit seesaw Library
|
||||
adafruit/Adafruit seesaw Library@1.7.9
|
||||
https://github.com/jp-bennett/LovyanGFX/archive/7458f84a126c1f8fdc7b038074f71be903f6e4c0.zip
|
||||
build_flags = ${native_base.build_flags}
|
||||
!pkg-config --cflags --libs sdl2 --silence-errors || :
|
||||
-D LGFX_SDL=1
|
||||
|
||||
[env:native-fb]
|
||||
extends = native_base
|
||||
build_type = release
|
||||
|
||||
@@ -4,4 +4,7 @@
|
||||
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||||
#define HAS_GPS 1
|
||||
#define MAX_RX_TOPHONE settingsMap[maxtophone]
|
||||
#define MAX_NUM_NODES settingsMap[maxnodes]
|
||||
#define MAX_NUM_NODES settingsMap[maxnodes]
|
||||
|
||||
// RAK12002 RTC Module
|
||||
#define RV3028_RTC (uint8_t)0b1010010
|
||||
@@ -1,6 +1,7 @@
|
||||
; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
|
||||
[env:gat562_mesh_trial_tracker]
|
||||
extends = nrf52840_base
|
||||
board_level = extra
|
||||
board = gat562_mesh_trial_tracker
|
||||
board_check = true
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
|
||||
@@ -208,7 +208,7 @@ No longer populated on PCB
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER (4.90F)
|
||||
#define ADC_MULTIPLIER (4.916F)
|
||||
|
||||
#define HAS_RTC 0
|
||||
#ifdef __cplusplus
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
; First prototype nrf52840/sx1262 device
|
||||
[env:heltec-mesh-solar]
|
||||
extends = nrf52840_base
|
||||
board = heltec_mesh_solar
|
||||
board_level = pr
|
||||
debug_tool = jlink
|
||||
|
||||
# add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-Ivariants/nrf52840/heltec_mesh_solar
|
||||
-DGPS_POWER_TOGGLE
|
||||
-DHELTEC_MESH_SOLAR
|
||||
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_solar>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
https://github.com/NMIoT/meshsolar/archive/dfc5330dad443982e6cdd37a61d33fc7252f468b.zip
|
||||
lewisxhe/PCF8563_Library@^1.0.1
|
||||
ArduinoJson@6.21.4
|
||||
@@ -0,0 +1,36 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0 - pins 0 and 1 are hardwired for xtal and should never be enabled
|
||||
0xff, 0xff, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
pinMode(BQ4050_EMERGENCY_SHUTDOWN_PIN, INPUT);
|
||||
}
|
||||
@@ -0,0 +1,157 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_HELTEC_NRF_
|
||||
#define _VARIANT_HELTEC_NRF_
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
#define USE_LFXO // Board uses 32khz crystal for LF
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (1)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
|
||||
#define PIN_LED1 (0 + 12) // green (confirmed on 1.0 board)
|
||||
#define LED_BLUE PIN_LED1 // fake for bluefruit library
|
||||
#define LED_GREEN PIN_LED1
|
||||
#define LED_BUILTIN LED_GREEN
|
||||
#define LED_STATE_ON 0 // State when LED is lit
|
||||
|
||||
#define HAS_NEOPIXEL // Enable the use of neopixels
|
||||
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
|
||||
#define NEOPIXEL_DATA (32+15) // gpio pin used to send data to the neopixels
|
||||
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
|
||||
|
||||
/*
|
||||
* Buttons
|
||||
*/
|
||||
#define PIN_BUTTON1 (32 + 10)
|
||||
// #define PIN_BUTTON2 (0 + 18) // 0.18 is labeled on the board as RESET but we configure it in the bootloader as a regular
|
||||
// GPIO
|
||||
|
||||
/*
|
||||
No longer populated on PCB
|
||||
*/
|
||||
#define PIN_SERIAL2_RX (0 + 9)
|
||||
#define PIN_SERIAL2_TX (0 + 10)
|
||||
// #define PIN_SERIAL2_EN (0 + 17)
|
||||
|
||||
/*
|
||||
* I2C
|
||||
*/
|
||||
|
||||
#define WIRE_INTERFACES_COUNT 2
|
||||
|
||||
// I2C bus 0
|
||||
// Routed to footprint for PCF8563TS RTC
|
||||
// Not populated on T114 V1, maybe in future?
|
||||
#define PIN_WIRE_SDA (0 + 6) // P0.26
|
||||
#define PIN_WIRE_SCL (0 + 26) // P0.26
|
||||
|
||||
// I2C bus 1
|
||||
// Available on header pins, for general use
|
||||
#define PIN_WIRE1_SDA (0 + 30) // P0.30
|
||||
#define PIN_WIRE1_SCL (0 + 5) // P0.13
|
||||
|
||||
/*
|
||||
* Lora radio
|
||||
*/
|
||||
|
||||
#define USE_SX1262
|
||||
// #define USE_SX1268
|
||||
#define SX126X_CS (0 + 24) // FIXME - we really should define LORA_CS instead
|
||||
#define LORA_CS (0 + 24)
|
||||
#define SX126X_DIO1 (0 + 20)
|
||||
// Note DIO2 is attached internally to the module to an analog switch for TX/RX switching
|
||||
// #define SX1262_DIO3 (0 + 21)
|
||||
// This is used as an *output* from the sx1262 and connected internally to power the tcxo, do not drive from the
|
||||
// main
|
||||
// CPU?
|
||||
#define SX126X_BUSY (0 + 17)
|
||||
#define SX126X_RESET (0 + 25)
|
||||
// Not really an E22 but TTGO seems to be trying to clone that
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
|
||||
/*
|
||||
* GPS pins
|
||||
*/
|
||||
|
||||
#define GPS_L76K
|
||||
|
||||
// #define PIN_GPS_RESET (32 + 6) // An output to reset L76K GPS. As per datasheet, low for > 100ms will reset the L76K
|
||||
// #define GPS_RESET_MODE LOW
|
||||
// #define PIN_GPS_EN (21)
|
||||
#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
|
||||
#define VEXT_ON_VALUE HIGH
|
||||
// #define GPS_EN_ACTIVE HIGH
|
||||
#define PIN_GPS_STANDBY (32 + 2) // An output to wake GPS, low means allow sleep, high means force wake
|
||||
#define PIN_GPS_PPS (32 + 4)
|
||||
// Seems to be missing on this new board
|
||||
// #define PIN_GPS_PPS (32 + 4) // Pulse per second input from the GPS
|
||||
#define GPS_TX_PIN (32 + 5) // This is for bits going TOWARDS the CPU
|
||||
#define GPS_RX_PIN (32 + 7) // This is for bits going TOWARDS the GPS
|
||||
|
||||
#define GPS_THREAD_INTERVAL 50
|
||||
|
||||
#define PIN_SERIAL1_RX GPS_TX_PIN
|
||||
#define PIN_SERIAL1_TX GPS_RX_PIN
|
||||
|
||||
/*
|
||||
* SPI Interfaces
|
||||
*/
|
||||
#define SPI_INTERFACES_COUNT 1
|
||||
|
||||
// For LORA, spi 0
|
||||
#define PIN_SPI_MISO (0 + 23)
|
||||
#define PIN_SPI_MOSI (0 + 22)
|
||||
#define PIN_SPI_SCK (0 + 19)
|
||||
|
||||
// #define PIN_PWR_EN (0 + 6)
|
||||
|
||||
// To debug via the segger JLINK console rather than the CDC-ACM serial device
|
||||
// #define USE_SEGGER
|
||||
|
||||
#define BQ4050_SDA_PIN (32+1) // I2C data line pin
|
||||
#define BQ4050_SCL_PIN (32+0) // I2C clock line pin
|
||||
#define BQ4050_EMERGENCY_SHUTDOWN_PIN (32+3) // Emergency shutdown pin
|
||||
|
||||
#define HAS_RTC 0
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@@ -4,6 +4,7 @@
|
||||
[env:meshlink]
|
||||
extends = nrf52840_base
|
||||
board = meshlink
|
||||
board_level = extra
|
||||
;board_check = true
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-I variants/nrf52840/meshlink
|
||||
|
||||
@@ -4,6 +4,7 @@
|
||||
[env:meshlink_eink]
|
||||
extends = nrf52840_base
|
||||
board = meshlink
|
||||
board_level = extra
|
||||
;board_check = true
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-I variants/nrf52840/meshlink_eink
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
; MeshTiny - Custom device based on GAT562 with encoder and buzzer support
|
||||
[env:meshtiny]
|
||||
extends = nrf52840_base
|
||||
board = meshtiny
|
||||
board_level = extra
|
||||
build_flags = ${nrf52840_base.build_flags} -Ivariants/nrf52840/meshtiny -D MESHTINY
|
||||
-DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
|
||||
-DRADIOLIB_EXCLUDE_SX128X=1
|
||||
-DRADIOLIB_EXCLUDE_SX127X=1
|
||||
-DRADIOLIB_EXCLUDE_LR11X0=1
|
||||
-D INPUTDRIVER_ENCODER_TYPE=2
|
||||
-D INPUTDRIVER_ENCODER_UP=4
|
||||
-D INPUTDRIVER_ENCODER_DOWN=26
|
||||
-D INPUTDRIVER_ENCODER_BTN=28
|
||||
-D USE_PIN_BUZZER=PIN_BUZZER
|
||||
-D MESHTASTIC_EXCLUDE_GPS=1
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/meshtiny>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
@@ -0,0 +1,54 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0
|
||||
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
// LED1 & LED2
|
||||
pinMode(PIN_LED1, OUTPUT);
|
||||
ledOff(PIN_LED1);
|
||||
|
||||
pinMode(PIN_LED2, OUTPUT);
|
||||
ledOff(PIN_LED2);
|
||||
|
||||
// 3V3 Power Rail
|
||||
pinMode(PIN_3V3_EN, OUTPUT);
|
||||
digitalWrite(PIN_3V3_EN, HIGH);
|
||||
|
||||
// Initialize Encoder pins
|
||||
pinMode(INPUTDRIVER_ENCODER_UP, INPUT_PULLUP);
|
||||
pinMode(INPUTDRIVER_ENCODER_DOWN, INPUT_PULLUP);
|
||||
pinMode(INPUTDRIVER_ENCODER_BTN, INPUT_PULLUP);
|
||||
|
||||
// Initialize Buzzer pin
|
||||
pinMode(PIN_BUZZER, OUTPUT);
|
||||
digitalWrite(PIN_BUZZER, LOW);
|
||||
}
|
||||
@@ -0,0 +1,199 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_MESHTINY_
|
||||
#define _VARIANT_MESHTINY_
|
||||
|
||||
#define MESHTINY
|
||||
|
||||
// #define RAK4630
|
||||
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
#define USE_LFXO // Board uses 32khz crystal for LF
|
||||
// define USE_LFRC // Board uses RC for LF
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (6)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
// LEDs
|
||||
#define PIN_LED1 (35)
|
||||
#define PIN_LED2 (36)
|
||||
|
||||
#define LED_BUILTIN PIN_LED1
|
||||
#define LED_CONN PIN_LED2
|
||||
|
||||
#define LED_GREEN PIN_LED1
|
||||
#define LED_BLUE PIN_LED2
|
||||
|
||||
#define LED_STATE_ON 1 // State when LED is litted
|
||||
|
||||
/*
|
||||
* Encoder
|
||||
*/
|
||||
#define INPUTDRIVER_ENCODER_TYPE 2
|
||||
#define INPUTDRIVER_ENCODER_UP 26
|
||||
#define INPUTDRIVER_ENCODER_DOWN 4
|
||||
#define INPUTDRIVER_ENCODER_BTN 28
|
||||
|
||||
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||||
|
||||
/*
|
||||
* Buzzer - PWM
|
||||
*/
|
||||
#define PIN_BUZZER 30
|
||||
|
||||
/*
|
||||
* Buttons
|
||||
*/
|
||||
|
||||
#define PIN_BUTTON1 9
|
||||
#define BUTTON_NEED_PULLUP
|
||||
#define PIN_BUTTON2 12
|
||||
#define PIN_BUTTON3 24
|
||||
#define PIN_BUTTON4 25
|
||||
|
||||
/*
|
||||
* Analog pins
|
||||
*/
|
||||
#define PIN_A0 (5)
|
||||
#define PIN_A1 (31)
|
||||
#define PIN_A2 (28)
|
||||
#define PIN_A3 (29)
|
||||
#define PIN_A4 (30)
|
||||
#define PIN_A5 (31)
|
||||
#define PIN_A6 (0xff)
|
||||
#define PIN_A7 (0xff)
|
||||
|
||||
static const uint8_t A0 = PIN_A0;
|
||||
static const uint8_t A1 = PIN_A1;
|
||||
static const uint8_t A2 = PIN_A2;
|
||||
static const uint8_t A3 = PIN_A3;
|
||||
static const uint8_t A4 = PIN_A4;
|
||||
static const uint8_t A5 = PIN_A5;
|
||||
static const uint8_t A6 = PIN_A6;
|
||||
static const uint8_t A7 = PIN_A7;
|
||||
#define ADC_RESOLUTION 14
|
||||
|
||||
// Other pins
|
||||
#define PIN_AREF (2)
|
||||
#define PIN_NFC1 (9)
|
||||
#define PIN_NFC2 (10)
|
||||
|
||||
static const uint8_t AREF = PIN_AREF;
|
||||
|
||||
/*
|
||||
* Serial interfaces
|
||||
*/
|
||||
#define PIN_SERIAL1_RX (15)
|
||||
#define PIN_SERIAL1_TX (16)
|
||||
|
||||
// Connected to Jlink CDC
|
||||
#define PIN_SERIAL2_RX (8)
|
||||
#define PIN_SERIAL2_TX (6)
|
||||
|
||||
/*
|
||||
* SPI Interfaces
|
||||
*/
|
||||
#define SPI_INTERFACES_COUNT 2
|
||||
|
||||
#define PIN_SPI_MISO (45)
|
||||
#define PIN_SPI_MOSI (44)
|
||||
#define PIN_SPI_SCK (43)
|
||||
|
||||
#define PIN_SPI1_MISO (29) // (0 + 29)
|
||||
#define PIN_SPI1_MOSI (30) // (0 + 30)
|
||||
#define PIN_SPI1_SCK (3) // (0 + 3)
|
||||
|
||||
static const uint8_t SS = 42;
|
||||
static const uint8_t MOSI = PIN_SPI_MOSI;
|
||||
static const uint8_t MISO = PIN_SPI_MISO;
|
||||
static const uint8_t SCK = PIN_SPI_SCK;
|
||||
|
||||
#define HAS_SCREEN 1
|
||||
#define USE_SSD1306
|
||||
|
||||
/*
|
||||
* Wire Interfaces
|
||||
*/
|
||||
#define WIRE_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_WIRE_SDA (13)
|
||||
#define PIN_WIRE_SCL (14)
|
||||
|
||||
// QSPI Pins
|
||||
#define PIN_QSPI_SCK 3
|
||||
#define PIN_QSPI_CS 22 // Changed from 26 to avoid conflict with encoder
|
||||
#define PIN_QSPI_IO0 27 // Changed from 30 to avoid conflict with buzzer
|
||||
#define PIN_QSPI_IO1 29
|
||||
#define PIN_QSPI_IO2 21 // Changed from 28 to avoid conflict with encoder button
|
||||
#define PIN_QSPI_IO3 2
|
||||
|
||||
// On-board QSPI Flash
|
||||
#define EXTERNAL_FLASH_DEVICES IS25LP080D
|
||||
#define EXTERNAL_FLASH_USE_QSPI
|
||||
|
||||
#define USE_SX1262
|
||||
#define SX126X_CS (42)
|
||||
#define SX126X_DIO1 (47)
|
||||
#define SX126X_BUSY (46)
|
||||
#define SX126X_RESET (38)
|
||||
#define SX126X_POWER_EN (37)
|
||||
// DIO2 controlls an antenna switch and the TCXO voltage is controlled by DIO3
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
|
||||
// Testing USB detection
|
||||
#define NRF_APM
|
||||
|
||||
#define PIN_3V3_EN (34)
|
||||
|
||||
// Battery
|
||||
// The battery sense is hooked to pin A0 (5)
|
||||
#define BATTERY_PIN PIN_A0
|
||||
// and has 12 bit resolution
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
||||
#define BATTERY_SENSE_RESOLUTION 4096.0
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER 1.73
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@@ -11,10 +11,10 @@ build_flags = ${nrf52840_base.build_flags}
|
||||
-DRADIOLIB_EXCLUDE_SX127X=1
|
||||
-DRADIOLIB_EXCLUDE_LR11X0=1
|
||||
-DHAS_RAKPROT=1 ; Define if RAk OneWireSerial is used (disables GPS)
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak2560> +<mesh/api/> +<mqtt/>
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak2560> +<mesh/api/> +<mqtt/> +<serialization/>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
${nrf52_networking_base.lib_deps}
|
||||
melopero/Melopero RV3028@^1.1.0
|
||||
https://github.com/beegee-tokyo/RAK-OneWireSerial/archive/0.0.2.zip
|
||||
debug_tool = jlink
|
||||
|
||||
@@ -17,11 +17,12 @@ build_flags = ${nrf52840_base.build_flags}
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak4631> +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
${nrf52_networking_base.lib_deps}
|
||||
melopero/Melopero RV3028@^1.1.0
|
||||
https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
|
||||
rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
|
||||
beegee-tokyo/RAK12035_SoilMoisture@^1.0.4
|
||||
# renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main
|
||||
https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip
|
||||
|
||||
; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
|
||||
|
||||
@@ -24,14 +24,15 @@ build_flags = ${nrf52840_base.build_flags}
|
||||
-DMESHTASTIC_EXCLUDE_STOREFORWARD=1
|
||||
-DMESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
|
||||
-DMESHTASTIC_EXCLUDE_WAYPOINT=1
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak4631_eth_gw> +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak4631_eth_gw> +<mesh/eth/> +<mesh/api/> +<mqtt/> +<serialization/>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
melopero/Melopero RV3028@^1.1.0
|
||||
https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
|
||||
rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
|
||||
https://github.com/meshtastic/RAK12034-BMX160/archive/4821355fb10390ba8557dc43ca29a023bcfbb9d9.zip
|
||||
# renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main
|
||||
https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip
|
||||
bblanchon/ArduinoJson @ 6.21.4
|
||||
; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
|
||||
; Note: as of 6/2013 the serial/bootloader based programming takes approximately 30 seconds
|
||||
|
||||
@@ -18,7 +18,7 @@ build_flags = ${nrf52840_base.build_flags}
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/rak_wismeshtap> +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
${nrf52_networking_base.lib_deps}
|
||||
melopero/Melopero RV3028@^1.1.0
|
||||
https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
|
||||
rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
|
||||
|
||||
@@ -18,16 +18,9 @@
|
||||
|
||||
// Shared NicheGraphics components
|
||||
// --------------------------------
|
||||
#include "graphics/niche/Drivers/Backlight/LatchingBacklight.h"
|
||||
#include "graphics/niche/Drivers/EInk/GDEY0213B74.h"
|
||||
#include "graphics/niche/Drivers/EInk/ZJY122250_0213BAAMFGN.h"
|
||||
#include "graphics/niche/Inputs/TwoButton.h"
|
||||
|
||||
// Special case - fix T-Echo's touch button
|
||||
// ----------------------------------------
|
||||
// On a handful of T-Echos, LoRa TX triggers the capacitive touch
|
||||
// To avoid this, we lockout the button during TX
|
||||
#include "mesh/RadioLibInterface.h"
|
||||
|
||||
void setupNicheGraphics()
|
||||
{
|
||||
using namespace NicheGraphics;
|
||||
@@ -41,7 +34,7 @@ void setupNicheGraphics()
|
||||
// E-Ink Driver
|
||||
// -----------------------------
|
||||
|
||||
Drivers::EInk *driver = new Drivers::GDEY0213B74;
|
||||
Drivers::EInk *driver = new Drivers::ZJY122250_0213BAAMFGN;
|
||||
driver->begin(&SPI1, PIN_EINK_DC, PIN_EINK_CS, PIN_EINK_BUSY, PIN_EINK_RES);
|
||||
|
||||
// InkHUD
|
||||
@@ -53,8 +46,7 @@ void setupNicheGraphics()
|
||||
inkhud->setDriver(driver);
|
||||
|
||||
// Set how many FAST updates per FULL update
|
||||
// Set how unhealthy additional FAST updates beyond this number are
|
||||
inkhud->setDisplayResilience(7, 1.5);
|
||||
inkhud->setDisplayResilience(15);
|
||||
|
||||
// Select fonts
|
||||
InkHUD::Applet::fontLarge = FREESANS_12PT_WIN1252;
|
||||
@@ -62,16 +54,10 @@ void setupNicheGraphics()
|
||||
InkHUD::Applet::fontSmall = FREESANS_6PT_WIN1252;
|
||||
|
||||
// Customize default settings
|
||||
inkhud->persistence->settings.userTiles.maxCount = 2; // Two applets side-by-side
|
||||
// 270 degrees clockwise
|
||||
inkhud->persistence->settings.rotation = 1; // 90 degrees clockwise
|
||||
inkhud->persistence->settings.optionalFeatures.batteryIcon = true; // Device definitely has a battery
|
||||
inkhud->persistence->settings.optionalMenuItems.backlight = true; // Until proves capacitive button works by touching it
|
||||
inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
|
||||
|
||||
// Setup backlight controller
|
||||
// Note: AUX button attached further down
|
||||
Drivers::LatchingBacklight *backlight = Drivers::LatchingBacklight::getInstance();
|
||||
backlight->setPin(PIN_EINK_EN);
|
||||
inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
|
||||
inkhud->persistence->settings.userTiles.maxCount = 2; // Two applets side-by-side
|
||||
|
||||
// Pick applets
|
||||
// Note: order of applets determines priority of "auto-show" feature
|
||||
@@ -83,11 +69,9 @@ void setupNicheGraphics()
|
||||
inkhud->addApplet("Recents List", new InkHUD::RecentsListApplet); // -
|
||||
inkhud->addApplet("Heard", new InkHUD::HeardApplet, true, false, 0); // Activated, no autoshow, default on tile 0
|
||||
|
||||
inkhud->persistence->settings.rotation = 1;
|
||||
// inkhud->persistence->printSettings(&inkhud->persistence->settings);
|
||||
// Start running InkHUD
|
||||
inkhud->begin();
|
||||
// inkhud->persistence->printSettings(&inkhud->persistence->settings);
|
||||
|
||||
// Buttons
|
||||
// --------------------------
|
||||
|
||||
|
||||
@@ -1,17 +1,47 @@
|
||||
[env:seeed_wio_tracker_L1_eink]
|
||||
board = seeed_wio_tracker_L1
|
||||
extends = nrf52840_base, inkhud
|
||||
extends = nrf52840_base
|
||||
;board_level = extra
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
${inkhud.build_flags}
|
||||
-I variants/nrf52840/seeed_wio_tracker_L1_eink
|
||||
-D SEEED_WIO_TRACKER_L1_EINK
|
||||
-D SEEED_WIO_TRACKER_L1
|
||||
-I src/platform/nrf52/softdevice
|
||||
-I src/platform/nrf52/softdevice/nrf52
|
||||
-DUSE_EINK
|
||||
-DEINK_DISPLAY_MODEL=GxEPD2_213_B74
|
||||
-DEINK_WIDTH=250
|
||||
-DEINK_HEIGHT=122
|
||||
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
|
||||
-DEINK_LIMIT_FASTREFRESH=10 ; How many consecutive fast-refreshes are permitted
|
||||
-DEINK_LIMIT_RATE_BACKGROUND_SEC=30 ; Minimum interval between BACKGROUND updates
|
||||
-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1 ; Minimum interval between RESPONSIVE updates
|
||||
; -D EINK_LIMIT_GHOSTING_PX=2000 ; (Optional) How much image ghosting is tolerated
|
||||
-DEINK_BACKGROUND_USES_FAST ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
|
||||
-DEINK_HASQUIRK_GHOSTING ; Display model is identified as "prone to ghosting"
|
||||
-DEINK_HASQUIRK_WEAKFASTREFRESH ; Pixels set with fast-refresh are easy to clear, disrupted by sunlight
|
||||
board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/seeed_wio_tracker_L1_eink> ${inkhud.build_src_filter}
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/seeed_wio_tracker_L1_eink>
|
||||
lib_deps =
|
||||
${inkhud.lib_deps}
|
||||
${nrf52840_base.lib_deps}
|
||||
https://github.com/meshtastic/GxEPD2#b202ebfec6a4821e098cf7a625ba0f6f2400292d
|
||||
debug_tool = jlink
|
||||
|
||||
[env:seeed_wio_tracker_L1_eink-inkhud]
|
||||
board = seeed_wio_tracker_L1
|
||||
extends = nrf52840_base, inkhud
|
||||
build_flags =
|
||||
${nrf52840_base.build_flags}
|
||||
${inkhud.build_flags}
|
||||
-I variants/nrf52840/seeed_wio_tracker_L1_eink
|
||||
-D SEEED_WIO_TRACKER_L1
|
||||
-D BUTTON_PIN=D13
|
||||
board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
|
||||
build_src_filter =
|
||||
${nrf52_base.build_src_filter}
|
||||
${inkhud.build_src_filter}
|
||||
+<../variants/nrf52840/seeed_wio_tracker_L1_eink>
|
||||
lib_deps =
|
||||
${inkhud.lib_deps} ; Before base libs_deps, so we use ZinggJM/GFXRoot instead of AdafruitGFX (saves space)
|
||||
${nrf52840_base.lib_deps}
|
||||
debug_tool = jlink
|
||||
@@ -33,17 +33,10 @@
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
// Button Configuration
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
|
||||
#ifdef BUTTON_PIN
|
||||
#undef BUTTON_PIN
|
||||
#endif
|
||||
|
||||
#define BUTTON_PIN D13 // This is the Program Button
|
||||
#define CANCEL_BUTTON_PIN D13 // This is the Program Button
|
||||
// #define BUTTON_NEED_PULLUP 1
|
||||
#define BUTTON_ACTIVE_LOW true
|
||||
#define BUTTON_ACTIVE_PULLUP false
|
||||
|
||||
#define BUTTON_PIN_TOUCH 13 // Touch button
|
||||
#define CANCEL_BUTTON_ACTIVE_LOW true
|
||||
#define CANCEL_BUTTON_ACTIVE_PULLUP false
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
// Digital Pin Mapping (D0-D10)
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
@@ -116,7 +109,7 @@ static const uint8_t SCL = PIN_WIRE_SCL;
|
||||
#define PIN_EINK_SCLK 31
|
||||
#define PIN_EINK_MOSI 33
|
||||
#define PIN_EINK_EN 14 // unused
|
||||
#define PIN_SPI1_MISO 15 // unused
|
||||
#define PIN_SPI1_MISO -1 // 15 unused
|
||||
#define PIN_SPI1_MOSI PIN_EINK_MOSI
|
||||
#define PIN_SPI1_SCK PIN_EINK_SCLK
|
||||
|
||||
@@ -175,7 +168,17 @@ static const uint8_t SCL = PIN_WIRE_SCL;
|
||||
// joystick
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
|
||||
// trackball
|
||||
#define HAS_TRACKBALL 1
|
||||
#define TB_UP 25
|
||||
#define TB_DOWN 26
|
||||
#define TB_LEFT 27
|
||||
#define TB_RIGHT 28
|
||||
#define TB_PRESS 29
|
||||
#define TB_DIRECTION FALLING
|
||||
|
||||
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||||
#define CANNED_MESSAGE_ADD_CONFIRMATION 1
|
||||
|
||||
// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
|
||||
// Compatibility Definitions
|
||||
|
||||
@@ -0,0 +1,25 @@
|
||||
; Using original screen class
|
||||
[env:t-echo-lite]
|
||||
extends = nrf52840_base
|
||||
board = t-echo
|
||||
board_check = true
|
||||
debug_tool = jlink
|
||||
|
||||
# add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-Ivariants/nrf52840/t-echo-lite
|
||||
-D T_ECHO_LITE
|
||||
-D GPS_POWER_TOGGLE
|
||||
-D EINK_DISPLAY_MODEL=GxEPD2_122_T61
|
||||
-D EINK_WIDTH=192
|
||||
-D EINK_HEIGHT=176
|
||||
-D USE_EINK
|
||||
-D USE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
|
||||
-D EINK_LIMIT_FASTREFRESH=20 ; How many consecutive fast-refreshes are permitted
|
||||
-D EINK_BACKGROUND_USES_FAST ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
|
||||
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/t-echo-lite>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
https://github.com/meshtastic/GxEPD2/archive/a05c11c02862624266b61599b0d6ba93e33c6f24.zip
|
||||
;upload_protocol = fs
|
||||
@@ -0,0 +1,44 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0 - pins 0 and 1 are hardwired for xtal and should never be enabled
|
||||
0xff, 0xff, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
// LED1 & LED2
|
||||
pinMode(PIN_LED1, OUTPUT);
|
||||
ledOff(PIN_LED1);
|
||||
|
||||
pinMode(PIN_LED2, OUTPUT);
|
||||
ledOff(PIN_LED2);
|
||||
|
||||
pinMode(PIN_LED3, OUTPUT);
|
||||
ledOff(PIN_LED3);
|
||||
}
|
||||
@@ -0,0 +1,207 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_TTGO_EINK_V1_0_
|
||||
#define _VARIANT_TTGO_EINK_V1_0_
|
||||
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
#define USE_LFXO // Board uses 32khz crystal for LF
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (1)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
// LEDs
|
||||
#define PIN_LED1 (32 + 7) // Green LED
|
||||
#define PIN_LED2 (32 + 5) // Blue LED
|
||||
// Unused(by firmware) LEDs:
|
||||
#define PIN_LED3 (32 + 14) // Red LED inside, under the display.
|
||||
|
||||
#define LED_RED PIN_LED3
|
||||
#define LED_BLUE PIN_LED2
|
||||
#define LED_GREEN PIN_LED1
|
||||
|
||||
#define BLE_LED LED_BLUE
|
||||
#define BLE_LED_INVERTED 1
|
||||
#define LED_BUILTIN LED_GREEN
|
||||
#define LED_CONN LED_GREEN
|
||||
#define LED_STATE_ON 0 // State when LED is lit
|
||||
|
||||
// Buttons
|
||||
#define PIN_BUTTON1 (0 + 24)
|
||||
#define PIN_BUTTON2 (0 + 18) // 0.18 is labeled on the board as RESET but we configure it in the bootloader as a regular GPIO
|
||||
|
||||
#define BUTTON_CLICK_MS 400
|
||||
|
||||
// Analog pins
|
||||
#define PIN_A0 (0 + 2) // Battery ADC
|
||||
|
||||
#define BATTERY_PIN PIN_A0
|
||||
|
||||
static const uint8_t A0 = PIN_A0;
|
||||
|
||||
#define ADC_RESOLUTION 14
|
||||
|
||||
#define ADC_CTRL (0 + 31)
|
||||
#define ADC_CTRL_ENABLED HIGH
|
||||
|
||||
// NFC
|
||||
#define PIN_NFC1 (9)
|
||||
#define PIN_NFC2 (10)
|
||||
|
||||
// Wire Interfaces
|
||||
#define WIRE_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_WIRE_SDA (32 + 4)
|
||||
#define PIN_WIRE_SCL (32 + 2)
|
||||
|
||||
/*
|
||||
Internal, PCB PAD interrupt PIN. Currently not used. (Not built in my device)
|
||||
*/
|
||||
// #define PIN_IMU_INT (0 + 16) // Interrupt from the IMU, macro name correct?!
|
||||
|
||||
// External serial flash ZD25WQ32CEIGR
|
||||
// QSPI Pins
|
||||
#define PIN_QSPI_SCK (0 + 4)
|
||||
#define PIN_QSPI_CS (0 + 12)
|
||||
#define PIN_QSPI_IO0 (0 + 6) // MOSI if using two bit interface
|
||||
#define PIN_QSPI_IO1 (0 + 8) // MISO if using two bit interface
|
||||
#define PIN_QSPI_IO2 (32 + 9) // WP if using two bit interface (i.e. not used)
|
||||
#define PIN_QSPI_IO3 (0 + 26) // HOLD if using two bit interface (i.e. not used)
|
||||
|
||||
// On-board QSPI Flash
|
||||
#define EXTERNAL_FLASH_DEVICES ZD25WQ32CEIGR
|
||||
#define EXTERNAL_FLASH_USE_QSPI
|
||||
|
||||
// Lora radio
|
||||
|
||||
#define USE_SX1262
|
||||
// #define USE_SX1268 // currently only available with XS1262.
|
||||
#define SX126X_CS (0 + 11)
|
||||
#define SX126X_DIO1 (32 + 8)
|
||||
#define SX126X_DIO2 (0 + 5)
|
||||
#define SX126X_BUSY (0 + 14)
|
||||
#define SX126X_RESET (0 + 7)
|
||||
#define SX126X_RXEN (32 + 1)
|
||||
#define SX126X_TXEN (0 + 27)
|
||||
// #define TCXO_OPTIONAL
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
|
||||
// eink display pins
|
||||
#define VEXT_ENABLE (32 + 12)
|
||||
#define VEXT_ON_VALUE LOW
|
||||
#define PIN_EINK_CS (0 + 22)
|
||||
#define PIN_EINK_BUSY (0 + 3)
|
||||
#define PIN_EINK_DC (0 + 21)
|
||||
#define PIN_EINK_RES (0 + 28)
|
||||
#define PIN_EINK_SCLK (0 + 19)
|
||||
#define PIN_EINK_MOSI (0 + 20)
|
||||
|
||||
// Controls power 3V3 for all peripherals (eink + GPS + LoRa + Sensor)
|
||||
#define PIN_POWER_EN (0 + 30) // 3V3 POWER Enable
|
||||
|
||||
#define PIN_SPI1_MISO (-1) // The display does not use MISO.
|
||||
#define PIN_SPI1_MOSI PIN_EINK_MOSI
|
||||
#define PIN_SPI1_SCK PIN_EINK_SCLK
|
||||
|
||||
// GPS pins
|
||||
// #define GPS_DEBUG
|
||||
#define GPS_L76K
|
||||
#define GPS_BAUDRATE 9600
|
||||
#define HAS_GPS 1
|
||||
// #define PIN_GPS_REINIT (32 + 5) // An output to reset L76K GPS. As per datasheet, low for > 100ms will reset the L76K
|
||||
|
||||
#define PIN_GPS_STANDBY (32 + 10) // An output to wake GPS, low means allow sleep, high means force wake
|
||||
// Seems to be missing on this new board
|
||||
#define PIN_GPS_PPS (0 + 29) // Pulse per second input from the GPS
|
||||
#define GPS_TX_PIN (32 + 15) // This is for bits going TOWARDS the CPU
|
||||
#define GPS_RX_PIN (32 + 13) // This is for bits going TOWARDS the GPS
|
||||
|
||||
#define GPS_THREAD_INTERVAL 50
|
||||
|
||||
#define PIN_SERIAL1_RX GPS_TX_PIN
|
||||
#define PIN_SERIAL1_TX GPS_RX_PIN
|
||||
|
||||
// SPI Interfaces
|
||||
#define SPI_INTERFACES_COUNT 2
|
||||
|
||||
// For LORA, SPI 0
|
||||
#define PIN_SPI_MISO (0 + 17)
|
||||
#define PIN_SPI_MOSI (0 + 15)
|
||||
#define PIN_SPI_SCK (0 + 13)
|
||||
|
||||
// Battery
|
||||
// The battery sense is hooked to pin A0 (2)
|
||||
// it is defined in the analogue pin section of this file
|
||||
// and has 12 bit resolution
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
||||
#define BATTERY_SENSE_RESOLUTION 4096.0
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER (2.0F)
|
||||
|
||||
// #define NO_EXT_GPIO 1
|
||||
// PINs back side
|
||||
// Batt & solar connector left up corner
|
||||
/*
|
||||
-------------------------------
|
||||
| VDDH, VBAT, 0.23, SCL , 1.06 |
|
||||
| GND , SDA , 0.09, 0.10, 0.25 |
|
||||
-------------------------------
|
||||
--------
|
||||
| VDDH |
|
||||
| GND |
|
||||
| 1.13 | - Wake Up/standby
|
||||
| 1.15 | - PPS
|
||||
| 0.29 | - TX
|
||||
| 1.10 | - RX
|
||||
| 1.11 | - EN
|
||||
--------
|
||||
-------------------------------
|
||||
| 3V3 , GND , 0.16, 1.03, G_WU | 0.16 internal solder pad interrupt PIN,
|
||||
| G_EN, G_RX, G_TX, GND , PPS |
|
||||
-------------------------------
|
||||
*/
|
||||
|
||||
// To debug via the segger JLINK console rather than the CDC-ACM serial device
|
||||
// #define USE_SEGGER
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@@ -124,8 +124,7 @@ extern "C" {
|
||||
#define GPS_RTC_INT (0 + 15) // P0.15, normal is LOW, wake by HIGH
|
||||
#define GPS_RESETB_OUT (32 + 14) // P1.14, always input pull_up
|
||||
|
||||
#define GPS_FIX_HOLD_TIME 15000 // ms
|
||||
#define BATTERY_PIN 2 // P0.02/AIN0, BAT_ADC
|
||||
#define BATTERY_PIN 2 // P0.02/AIN0, BAT_ADC
|
||||
#define BATTERY_IMMUTABLE
|
||||
#define ADC_MULTIPLIER (2.0F)
|
||||
// P0.04/AIN2 is VCC_ADC, P0.05/AIN3 is CHARGER_DET, P1.03 is CHARGE_STA, P1.04 is CHARGE_DONE
|
||||
|
||||
@@ -123,7 +123,6 @@ extern "C" {
|
||||
#define GPS_RESETB_OUT (32 + 14) // P1.14, awlays input pull_up
|
||||
|
||||
// #define GPS_THREAD_INTERVAL 50
|
||||
#define GPS_FIX_HOLD_TIME 15000 // ms
|
||||
|
||||
#define BATTERY_PIN 2
|
||||
// #define ADC_CHANNEL ADC1_GPIO2_CHANNEL
|
||||
@@ -157,4 +156,4 @@ extern "C" {
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif // _VARIANT_WIO_SDK_WM1110_
|
||||
#endif // _VARIANT_WIO_SDK_WM1110_
|
||||
|
||||
@@ -0,0 +1,79 @@
|
||||
#pragma once
|
||||
|
||||
#define PINS_COUNT (25u)
|
||||
#define NUM_DIGITAL_PINS (25u)
|
||||
#define NUM_ANALOG_INPUTS (4u)
|
||||
#define NUM_ANALOG_OUTPUTS (0u)
|
||||
#define ADC_RESOLUTION (12u)
|
||||
|
||||
// LEDs
|
||||
#define PIN_LED (24u)
|
||||
|
||||
// Serial
|
||||
#define PIN_SERIAL1_TX (16u)
|
||||
#define PIN_SERIAL1_RX (17u)
|
||||
|
||||
// SPI
|
||||
#define PIN_SPI0_MISO (20u)
|
||||
#define PIN_SPI0_MOSI (23u)
|
||||
#define PIN_SPI0_SCK (22u)
|
||||
#define PIN_SPI0_SS (21u)
|
||||
|
||||
// Connected to LoRa module
|
||||
#define PIN_SPI1_MISO (12u)
|
||||
#define PIN_SPI1_MOSI (11u)
|
||||
#define PIN_SPI1_SCK (10u)
|
||||
#define PIN_SPI1_SS (9u)
|
||||
#define RFM95W_SS (9u)
|
||||
#define RFM95W_DIO0 (14u)
|
||||
#define RFM95W_DIO1 (15u)
|
||||
#define RFM95W_DIO2 (18u)
|
||||
#define RFM95W_RST (13u)
|
||||
#define RFM95W_SPI SPI1
|
||||
|
||||
// Wire
|
||||
#define PIN_WIRE0_SDA (0u)
|
||||
#define PIN_WIRE0_SCL (1u)
|
||||
|
||||
// Not pinned out
|
||||
#define PIN_WIRE1_SDA (31u)
|
||||
#define PIN_WIRE1_SCL (31u)
|
||||
#define PIN_SERIAL2_RX (31u)
|
||||
#define PIN_SERIAL2_TX (31u)
|
||||
|
||||
#define SERIAL_HOWMANY (1u)
|
||||
#define SPI_HOWMANY (2u)
|
||||
#define WIRE_HOWMANY (1u)
|
||||
|
||||
#define LED_BUILTIN PIN_LED
|
||||
|
||||
static const uint8_t D0 = (16u);
|
||||
static const uint8_t D1 = (17u);
|
||||
static const uint8_t D2 = (20u);
|
||||
static const uint8_t D3 = (23u);
|
||||
static const uint8_t D4 = (22u);
|
||||
static const uint8_t D5 = (2u);
|
||||
static const uint8_t D6 = (3u);
|
||||
static const uint8_t D7 = (0u);
|
||||
static const uint8_t D8 = (1u);
|
||||
static const uint8_t D9 = (4u);
|
||||
static const uint8_t D10 = (5u);
|
||||
static const uint8_t D11 = (6u);
|
||||
static const uint8_t D12 = (7u);
|
||||
static const uint8_t D13 = (8u);
|
||||
static const uint8_t D14 = (13u);
|
||||
static const uint8_t D15 = (14u);
|
||||
static const uint8_t D16 = (15u);
|
||||
static const uint8_t D17 = (18u);
|
||||
static const uint8_t D18 = (24u);
|
||||
|
||||
static const uint8_t A0 = (26u);
|
||||
static const uint8_t A1 = (27u);
|
||||
static const uint8_t A2 = (28u);
|
||||
static const uint8_t A3 = (29u);
|
||||
static const uint8_t A4 = (19u);
|
||||
static const uint8_t A5 = (21u);
|
||||
|
||||
#ifndef SS
|
||||
#define SS PIN_SPI1_SS
|
||||
#endif
|
||||
@@ -0,0 +1,16 @@
|
||||
[env:challenger_2040_lora]
|
||||
extends = rp2040_base
|
||||
board = challenger_2040_lora
|
||||
board_level = extra
|
||||
upload_protocol = picotool
|
||||
# add our variants files to the include and src paths
|
||||
build_flags =
|
||||
${rp2040_base.build_flags}
|
||||
-D PRIVATE_HW
|
||||
-I variants/rp2040/challenger_2040_lora
|
||||
-D DEBUG_RP2040_PORT=Serial
|
||||
-D HW_SPI1_DEVICE
|
||||
lib_deps =
|
||||
${rp2040_base.lib_deps}
|
||||
debug_build_flags = ${rp2040_base.build_flags}
|
||||
debug_tool = cmsis-dap ; for e.g. Picotool
|
||||
@@ -0,0 +1,39 @@
|
||||
// Define SS for compatibility with libraries expecting a default SPI chip select pin
|
||||
|
||||
#define ARDUINO_ARCH_AVR
|
||||
|
||||
#define EXT_NOTIFY_OUT 0xFFFFFFFF
|
||||
#define BUTTON_PIN 0xFFFFFFFF
|
||||
|
||||
#define LED_PIN PIN_LED
|
||||
|
||||
#define USE_RF95 // RFM95/SX127x
|
||||
|
||||
#undef LORA_SCK
|
||||
#undef LORA_MISO
|
||||
#undef LORA_MOSI
|
||||
#undef LORA_CS
|
||||
|
||||
// https://gitlab.com/invectorlabs/hw/challenger_rp2040_lora
|
||||
#define LORA_SCK 10 // Clock
|
||||
#define LORA_CS 9 // Chip Select
|
||||
#define LORA_MOSI 11 // Serial Data Out
|
||||
#define LORA_MISO 12 // Serial Data In
|
||||
|
||||
#define LORA_RESET 13 // Reset
|
||||
|
||||
#define LORA_DIO0 14 // DIO0
|
||||
#define LORA_DIO1 15 // DIO1
|
||||
#define LORA_DIO2 18 // DIO2
|
||||
#define LORA_DIO3 0xFFFFFFFF // Not connected
|
||||
#define LORA_DIO4 0xFFFFFFFF // Not connected
|
||||
#define LORA_DIO5 0xFFFFFFFF // Not connected
|
||||
|
||||
#ifdef USE_SX1262
|
||||
#define SX126X_CS LORA_CS
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_BUSY LORA_DIO2
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
// #define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#endif
|
||||
@@ -1,6 +1,7 @@
|
||||
[env:catsniffer]
|
||||
extends = rp2040_base
|
||||
board = rpipico
|
||||
board_level = extra
|
||||
upload_protocol = picotool
|
||||
build_flags =
|
||||
${rp2040_base.build_flags}
|
||||
|
||||
@@ -12,7 +12,5 @@ build_flags =
|
||||
-DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
|
||||
-DMESHTASTIC_EXCLUDE_I2C=1
|
||||
-DMESHTASTIC_EXCLUDE_GPS=1
|
||||
;-DPIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF
|
||||
;-DCFG_DEBUG
|
||||
|
||||
upload_port = stlink
|
||||
@@ -0,0 +1,9 @@
|
||||
// From E77-900M22S Product Specification
|
||||
// https://www.cdebyte.com/pdf-down.aspx?id=2963
|
||||
// Note 1: PA6 and PA7 pins are used as internal control RF switches of the module, PA6 = RF_TXEN, PA7 = RF_RXEN, RF_TXEN=1
|
||||
// RF_RXEN=0 is the transmit channel, and RF_TXEN=0 RF_RXEN=1 is the receiving channel
|
||||
|
||||
static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA7, PA6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
|
||||
|
||||
static const Module::RfSwitchMode_t rfswitch_table[4] = {
|
||||
{STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
|
||||
@@ -18,5 +18,4 @@ Do not expect a working Meshtastic device with this target.
|
||||
#define LED_PIN PB4 // LED1
|
||||
// #define LED_PIN PB3 // LED2
|
||||
#define LED_STATE_ON 1
|
||||
|
||||
#endif
|
||||
|
||||
@@ -6,10 +6,14 @@ board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
|
||||
build_flags =
|
||||
${stm32_base.build_flags}
|
||||
-Ivariants/stm32/rak3172
|
||||
-DRAK3172
|
||||
-DENABLE_HWSERIAL1
|
||||
-DPIN_SERIAL1_RX=PB7
|
||||
-DPIN_SERIAL1_TX=PB6
|
||||
-DPIN_WIRE_SDA=PA11
|
||||
-DPIN_WIRE_SCL=PA12
|
||||
-DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
|
||||
-DMESHTASTIC_EXCLUDE_I2C=1
|
||||
-DMESHTASTIC_EXCLUDE_GPS=1
|
||||
;-DCFG_DEBUG
|
||||
|
||||
upload_port = stlink
|
||||
|
||||
@@ -0,0 +1,7 @@
|
||||
// Pins from https://forum.rakwireless.com/t/rak3172-internal-schematic/4557/2
|
||||
// PB8, PC13
|
||||
|
||||
static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PB8, PC13, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
|
||||
|
||||
static const Module::RfSwitchMode_t rfswitch_table[4] = {
|
||||
{STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
|
||||
@@ -0,0 +1,8 @@
|
||||
/* https://wiki.seeedstudio.com/LoRa-E5_STM32WLE5JC_Module/
|
||||
* Wio-E5 module ONLY transmits through RFO_HP
|
||||
* Receive: PA4=1, PA5=0
|
||||
* Transmit(high output power, SMPS mode): PA4=0, PA5=1 */
|
||||
static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA4, PA5, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
|
||||
|
||||
static const Module::RfSwitchMode_t rfswitch_table[4] = {
|
||||
{STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
|
||||
Reference in New Issue
Block a user