Merge branch 'master' into crowpanelV2

variants/esp32s3/esp32s3.ini

@@ -0,0 +1,5 @@
+[esp32s3_base]
+extends = esp32_base
+custom_esp32_kind = esp32s3
+
+monitor_speed = 115200

variants/esp32s3/hackaday-communicator/pins_arduino.h

@@ -0,0 +1,59 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// static const uint8_t TX = 43;
+// static const uint8_t RX = 44;
+
+static const uint8_t SDA = 47;
+static const uint8_t SCL = 14;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 17;
+static const uint8_t MOSI = 3;
+static const uint8_t MISO = 9;
+static const uint8_t SCK = 8;
+
+static const uint8_t A0 = 1;
+static const uint8_t A1 = 2;
+static const uint8_t A2 = 3;
+static const uint8_t A3 = 4;
+static const uint8_t A4 = 5;
+static const uint8_t A5 = 6;
+static const uint8_t A6 = 7;
+static const uint8_t A7 = 8;
+static const uint8_t A8 = 9;
+static const uint8_t A9 = 10;
+static const uint8_t A10 = 11;
+static const uint8_t A11 = 12;
+static const uint8_t A12 = 13;
+static const uint8_t A13 = 14;
+static const uint8_t A14 = 15;
+static const uint8_t A15 = 16;
+static const uint8_t A16 = 17;
+static const uint8_t A17 = 18;
+static const uint8_t A18 = 19;
+static const uint8_t A19 = 20;
+
+static const uint8_t T1 = 1;
+static const uint8_t T2 = 2;
+static const uint8_t T3 = 3;
+static const uint8_t T4 = 4;
+static const uint8_t T5 = 5;
+static const uint8_t T6 = 6;
+static const uint8_t T7 = 7;
+static const uint8_t T8 = 8;
+static const uint8_t T9 = 9;
+static const uint8_t T10 = 10;
+static const uint8_t T11 = 11;
+static const uint8_t T12 = 12;
+static const uint8_t T13 = 13;
+static const uint8_t T14 = 14;
+
+// static const uint8_t BAT_ADC_PIN = 4;
+
+#endif /* Pins_Arduino_h */

variants/esp32s3/hackaday-communicator/platformio.ini

@@ -0,0 +1,15 @@
+; Hackaday Communicator
+[env:hackaday-communicator]
+extends = esp32s3_base
+board = hackaday-communicator
+board_check = true
+board_build.partitions = default_16MB.csv
+upload_protocol = esptool
+
+build_flags = ${esp32s3_base.build_flags} 
+  -D HACKADAY_COMMUNICATOR
+  -D BOARD_HAS_PSRAM
+  -I variants/esp32s3/hackaday-communicator
+
+lib_deps = ${esp32s3_base.lib_deps}
+  https://github.com/meshtastic/Arduino_GFX/archive/054e81ffaf23784830a734e3c184346789349406.zip

variants/esp32s3/hackaday-communicator/variant.h

@@ -0,0 +1,61 @@
+#define TFT_BL 2
+#define SPI_FREQUENCY 2000000
+#define SPI_READ_FREQUENCY 16000000
+#define TFT_HEIGHT 142
+#define TFT_WIDTH 428
+#define TFT_OFFSET_X 0
+#define TFT_OFFSET_Y 0
+#define TFT_OFFSET_ROTATION 0
+#define SCREEN_TRANSITION_FRAMERATE 5
+#define HAS_SCREEN 1
+#define TFT_BLACK 0
+#define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
+#define USE_TFTDISPLAY 1
+
+#define USE_POWERSAVE
+#define SLEEP_TIME 120
+
+#define GPS_DEFAULT_NOT_PRESENT 1
+// #define GPS_RX_PIN 44
+// #define GPS_TX_PIN 43
+
+// #define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+//  ratio of voltage divider = 2.0 (RD2=100k, RD3=100k)
+// #define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+// #define ADC_CHANNEL ADC1_GPIO4_CHANNEL
+
+// keyboard
+#define I2C_SDA 47 // I2C pins for this board
+#define I2C_SCL 14
+// #define KB_POWERON -1                  // must be set to HIGH
+// #define KB_SLAVE_ADDRESS TDECK_KB_ADDR // 0x55
+// #define KB_BL_PIN 46                   // not used for now
+#define KB_INT 13
+#define CANNED_MESSAGE_MODULE_ENABLE 1
+
+#define TFT_DC 39
+#define TFT_CS 41
+
+// LoRa
+#define USE_SX1262
+
+#define LORA_SCK 8
+#define LORA_MISO 9
+#define LORA_MOSI 3
+#define LORA_CS 17
+
+// #define LORA_DIO0 -1 // a No connect on the SX1262 module
+#define LORA_RESET 18
+#define LORA_DIO1 16 // SX1262 IRQ
+#define LORA_DIO2 15 // SX1262 BUSY
+// #define LORA_DIO3    // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
+
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+
+// #define LED_PIN 1

variants/esp32s3/heltec_v4/variant.h

@@ -34,6 +34,9 @@
 #define LORA_PA_EN 2
 #define LORA_PA_TX_EN 46 // enable tx
 
+#if HAS_TFT
+#define USE_TFTDISPLAY 1
+#endif
 /*
  * GPS pins
  */

variants/esp32s3/heltec_wireless_tracker/variant.h

@@ -27,6 +27,7 @@
 #define TFT_OFFSET_Y -1
 #define SCREEN_TRANSITION_FRAMERATE 3 // fps
 #define DISPLAY_FORCE_SMALL_FONTS
+#define USE_TFTDISPLAY 1
 
 // pin 3 is Vext on v1.1 - HIGH enables LDO for Vext rail which goes to:
 // GPS UC6580:          GPS V_DET(8), VDD_IO(7), DCDC_IN(21), pulls up RESETN(17), D_SEL(33) and BOOT_MODE(34) through 10kR

variants/esp32s3/heltec_wireless_tracker_V1_0/variant.h

@@ -27,6 +27,8 @@
 #define VTFT_CTRL 46                  // Heltec Tracker needs this pulled low for TFT
 #define SCREEN_TRANSITION_FRAMERATE 3 // fps
 #define DISPLAY_FORCE_SMALL_FONTS
+#define FORCE_LOW_RES 1
+#define USE_TFTDISPLAY 1
 
 #define VEXT_ENABLE Vext // active low, powers the oled display and the lora antenna boost
 #define VEXT_ON_VALUE LOW

variants/esp32s3/heltec_wireless_tracker_v2/variant.h

@@ -27,6 +27,7 @@
 #define TFT_INVERT false
 #define SCREEN_TRANSITION_FRAMERATE 3 // fps
 #define DISPLAY_FORCE_SMALL_FONTS
+#define USE_TFTDISPLAY 1
 
 #define VEXT_ENABLE 3 // active HIGH - powers the GPS, GPS LNA and OLED
 #define VEXT_ON_VALUE HIGH

variants/esp32s3/picomputer-s3/variant.h

@@ -32,6 +32,7 @@
 #define ST7789_CS 6
 #define ST7789_RS 1
 #define ST7789_BL 5
+#define USE_TFTDISPLAY 1
 
 #define ST7789_RESET -1
 #define ST7789_MISO -1

variants/esp32s3/seeed-sensecap-indicator/variant.h

@@ -37,6 +37,7 @@
 #define TFT_BL 45
 #define SCREEN_ROTATE
 #define SCREEN_TRANSITION_FRAMERATE 5 // fps
+#define USE_TFTDISPLAY 1
 
 #define HAS_TOUCHSCREEN 1
 #define SCREEN_TOUCH_INT (6 | IO_EXPANDER)

variants/esp32s3/t-deck/variant.h

@@ -22,6 +22,7 @@
 #define SCREEN_ROTATE
 #define SCREEN_TRANSITION_FRAMERATE 5
 #define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
+#define USE_TFTDISPLAY 1
 
 #define HAS_TOUCHSCREEN 1
 #define SCREEN_TOUCH_INT 16

variants/esp32s3/t-watch-s3/variant.h

@@ -18,6 +18,7 @@
 #define TFT_OFFSET_ROTATION 2
 #define SCREEN_ROTATE
 #define SCREEN_TRANSITION_FRAMERATE 5 // fps
+#define USE_TFTDISPLAY 1
 
 #define HAS_TOUCHSCREEN 1
 #define SCREEN_TOUCH_INT 16

variants/esp32s3/tlora-pager/variant.h

@@ -20,6 +20,7 @@
 #define SCREEN_ROTATE
 #define SCREEN_TRANSITION_FRAMERATE 5
 #define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
+#define USE_TFTDISPLAY 1
 
 #define I2C_SDA SDA
 #define I2C_SCL SCL

variants/esp32s3/tlora_t3s3_epaper/platformio.ini

@@ -13,7 +13,10 @@ build_flags =
   -DEINK_WIDTH=250
   -DEINK_HEIGHT=122
   -DUSE_EINK_DYNAMICDISPLAY            ; Enable Dynamic EInk
-  -DEINK_LIMIT_FASTREFRESH=10          ; How many consecutive fast-refreshes are permitted
+  -DEINK_LIMIT_FASTREFRESH=20          ; How many consecutive fast-refreshes are permitted    //20
+  -DEINK_LIMIT_RATE_BACKGROUND_SEC=30  ; Minimum interval between BACKGROUND updates          //30
+  -DEINK_LIMIT_RATE_RESPONSIVE_SEC=1   ; Minimum interval between RESPONSIVE updates
+  -DEINK_BACKGROUND_USES_FAST          ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
 
 lib_deps =
   ${esp32s3_base.lib_deps}

variants/esp32s3/tracksenger/internal/variant.h

@@ -28,6 +28,7 @@
 #define TFT_OFFSET_Y -1
 #define SCREEN_TRANSITION_FRAMERATE 3 // fps
 #define DISPLAY_FORCE_SMALL_FONTS
+#define USE_TFTDISPLAY 1
 
 #define VEXT_ENABLE 3 // active HIGH, powers the lora antenna boost
 #define VEXT_ON_VALUE HIGH

variants/esp32s3/tracksenger/lcd/variant.h

@@ -16,6 +16,7 @@
 #define ST7789_CS 38
 #define ST7789_RS 40
 #define ST7789_BL 21
+#define USE_TFTDISPLAY 1
 // P#define TFT_BL 21 /* V1.1 PCB marking */
 
 #define ST7789_RESET -1

variants/esp32s3/unphone/variant.h

@@ -36,6 +36,7 @@
 #define TFT_INVERT false
 #define SCREEN_ROTATE true
 #define SCREEN_TRANSITION_FRAMERATE 5
+#define USE_TFTDISPLAY 1
 
 #define HAS_TOUCHSCREEN 1
 #define USE_XPT2046 1