feat(variants): add Seeed Wio Tracker L1 Pro 1W (#11542)

* fix(sx126x): allow boards to opt out of the PA optimization table

Boards driving an external PA can define SX126X_NO_POWER_OPTIMIZATION_TABLE
to use the fixed PA config instead of RadioLib's table, which is tuned for a
bare SX126x.

Default behaviour is unchanged. init() applies the fixed config after begin(),
which programs power through the table.

* feat(variants): add Seeed Wio Tracker L1 Pro 1W

nRF52840 + SX1262 with a 1 W external PA, L76K GNSS, SH1106 OLED.

Uses hw_model 144 (meshtastic/protobufs#1038), opts into
SX126X_NO_POWER_OPTIMIZATION_TABLE and declares SX126X_MAX_POWER explicitly.
The PA gain table is indexed by SX1262 output power in dBm.

Requires protobufs#1038 and a protobuf regen before it builds.

* chore(deps): bump RadioLib to 510e00cf

Carries the current LR11x0 and LR2021 fixes.

* fix(variants): correct L1 Pro 1W QSPI pins and clean up comments

PIN_QSPI_* are logical pin indices. The QSPI flash sits at D19-D24 in
variant.cpp, but the defines carried D21-D26 from seeed_solar_node, where
that block does start at D21. D25 and D26 are trackball pins.

Also replaces mis-encoded characters in the pin comments and drops the
migration note, which referenced a private repo path and a stale PINS_COUNT.

* fix(variants): move L1 Pro 1W out of the per-PR build matrix

board_level = pr is the high-attention tier that builds on every PR. This
board belongs with the mainline set, which uses board_level = release.

src/configuration.h

@@ -205,6 +205,13 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define TX_GAIN_LORA 7, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 9, 8
 #endif
 
+#ifdef SEEED_WIO_TRACKER_L1_PRO_1W
+// Indexed by SX1262 output power in dBm, matching RadioInterface::limitPower().
+// TODO: verify against measured output.
+#define NUM_PA_POINTS 22
+#define TX_GAIN_LORA 10, 10, 10, 10, 10, 10, 10, 10, 10, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 11, 10, 10
+#endif
+
 // Default system gain to 0 if not defined
 #ifndef NUM_PA_POINTS
 #define NUM_PA_POINTS 1
@@ -234,7 +241,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define SSD1306_ADDRESS_L 0x3C // Addr = 0
 #define SSD1306_ADDRESS_H 0x3D // Addr = 1
 
-#if defined(SEEED_WIO_TRACKER_L1) && !defined(SEEED_WIO_TRACKER_L1_EINK)
+#if (defined(SEEED_WIO_TRACKER_L1) || defined(SEEED_WIO_TRACKER_L1_PRO_1W)) && !defined(SEEED_WIO_TRACKER_L1_EINK)
 #define SSD1306_ADDRESS SSD1306_ADDRESS_H
 #define USE_SH1106
 #endif

src/mesh/SX126xInterface.cpp

@@ -176,6 +176,12 @@ template <typename T> bool SX126xInterface<T>::init()
     if (res == RADIOLIB_ERR_NONE)
         res = lora.setCRC(RADIOLIB_SX126X_LORA_CRC_ON);
 
+#ifdef SX126X_NO_POWER_OPTIMIZATION_TABLE
+    // begin() applied the optimization table; re-apply the fixed PA config.
+    if (res == RADIOLIB_ERR_NONE)
+        res = lora.setOutputPower(power, false);
+#endif
+
     if (res == RADIOLIB_ERR_NONE)
         startReceive(); // start receiving
 
@@ -226,7 +232,11 @@ template <typename T> bool SX126xInterface<T>::reconfigure()
     if (power < -9)
         power = -9;
 
+#ifdef SX126X_NO_POWER_OPTIMIZATION_TABLE
+    err = lora.setOutputPower(power, false); // external PA: fixed PA config
+#else
     err = lora.setOutputPower(power);
+#endif
     if (err != RADIOLIB_ERR_NONE) {
         // Don't abort: this power is operator config (tx_power/SX126X_MAX_POWER); a value above the
         // driver's max would crash the daemon before reloadConfig() persists. Flag it and keep prior power.
@@ -525,4 +535,4 @@ template <typename T> void SX126xInterface<T>::setTransmitEnable(bool txon)
 #endif
 }
 
-#endif
+#endif

src/platform/nrf52/architecture.h

@@ -137,6 +137,8 @@
 #define HW_VENDOR meshtastic_HardwareModel_HELTEC_MESH_POCKET
 #elif defined(SEEED_WIO_TRACKER_L1_EINK)
 #define HW_VENDOR meshtastic_HardwareModel_SEEED_WIO_TRACKER_L1_EINK
+#elif defined(SEEED_WIO_TRACKER_L1_PRO_1W)
+#define HW_VENDOR meshtastic_HardwareModel_SEEED_WIO_TRACKER_L1_PRO_1W
 #elif defined(SEEED_WIO_TRACKER_L1)
 #define HW_VENDOR meshtastic_HardwareModel_SEEED_WIO_TRACKER_L1
 #elif defined(HELTEC_MESH_SOLAR)