* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Preliminary Thinknode M4 Support
* oops
* Fix RF switch TX configuration
* trunk'd
* GPS fix for M4
* Battery handling and LED for M4
* Trunk
* Drop debug warnings
* Make Red LED notification
* Merge cleanup
* Make white LEDs flash during charge
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Add support for RAK3112 variant with necessary configurations and definitions
* Add the configuration of the LED pin
* Refactor rak3112 variant configuration: update name, remove unused files,
* Update RAK3112 configuration: refine memory settings, adjust GPS pin definitions
* Update RAK3112 hardware vendor definition to use correct model
* configure LED pins and update module definitions
* Update USB mode configuration for RAK3112 board
* Update power and battery configuration in rak3112 variant
* Cancel the modification of mesh.pb.h
* Rename RAKwireless RAK3112 to RAK3312
---------
Co-authored-by: daniel <daniel.cao@rakwireless.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* add support for GAT562 Mesh Trial Tracker
* Hardware Model Definition for GAT562_MESH_TRIAL_TRACKER
* Added RAK4630 for led pin 2 (blue)
* Added RAK4630 for led pin 2 (blue) comment
* don't touch src/mesh/NodeDB.cpp
* set fixed baudrate for gat562_mesh_trial_tracker
* adjust the order of the HW_VENDOR defines
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Add support for MeshLink
* Updated, enabled watchdog and added button definition
* added eink variant and removed some compile errors
* Small board json file edit
* Finally got trunk working (somehow?), this is just cleanup with trunk fmt
* Various improvements and cleanup. Removed the use of PIN_3V3_En and defined a specific WD_EN pin instead for better clarity. Will do a bit more testing asap to make sure everything still works as intended :)
* Enable on-board QSPI Flash
* run trunk fmt with clang-format
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
* update indicator board
* Fixed the issue that indicator device uploads via rp2040 serial port in some cases.
* esp debug logs
* USB mode=1 messed up the debug log
* dummy for config transfer (#5154)
---------
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: virgil <virgil.wang.cj@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
In 2020, geeksville had a NRF52840-dk development board with a
busted oscilliator. Let's retire it from service :)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The lora-relay boards were important pathfinders for nrf52
support some years back. They are no longer commonly produced and
there are now many nrf52 options on the market. Retire these
boards and associated variant.
