11 Commits
Author SHA1 Message Date
Jonathan BennettandClaude Fable 5 5baad2e2a8 logging: compile out LOG_TRACE by default, demote chatty DEBUG lines, drop redundant logs (#11391)
* logging: gate LOG_TRACE behind MESHTASTIC_TRACE_LOGGING, drop redundant reclock logs

LOG_TRACE now compiles out by default so trace-level diagnostics cost no
flash; enable with -DMESHTASTIC_TRACE_LOGGING. Portduino keeps it on for
the traceFilename packet-trace feature.

Remove the 66 caller-side I2C reclock/restore log lines in the telemetry
sensors: ReClockI2C::setClock/restoreClock already log both frequencies
internally (now at trace level, since they fire every sensor read).

Also unify near-duplicate literals (colon/case/punctuation variants) so
linker string dedup applies, and drop an information-free bare 'done'.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* logging: demote chatty per-packet/per-poll DEBUG lines to trace level

With LOG_TRACE compiled out by default, per-iteration chatter (packet
bookkeeping, sensor poll values, e-ink refresh reasons, GPS pin states,
UI runState traces) now costs no flash on device builds while remaining
one -DMESHTASTIC_TRACE_LOGGING away. 108 lines demoted, 4 information-
free lines removed; failure paths, drop reasons, and one-time init logs
all stay at debug level.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* logging: address CodeRabbit review on trace-gate PR

- GPS: pass serial-derived buffers as %s args, never as format strings
  (untrusted bytes could contain % directives)
- 0x%08x for packet id / NodeNum per convention (Router, CannedMessage,
  NeighborInfo); unsigned casts for size_t args; %u for uint32_t delta
- EInk: async full-refresh begin/complete back to DEBUG (rare state
  transitions); per-frame SKIPPED lines stay trace

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* logging: gate trace on the flag's value, not its presence

-DMESHTASTIC_TRACE_LOGGING=0 previously *enabled* trace logging because
the gate tested definedness. The flag now defaults per-platform
(portduino 1, else 0) and both backends test the value, so =0 disables,
=1 or a bare -D enables. Also cast tx_after-millis() to uint32_t for %u
(millis() is unsigned long on native).

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* logging: clang-format rewrap after specifier widening

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* Even fewer bytes!

* logging: keep compile-gated debug lines at debug level; fix native-suite-count

Lines already inside default-off #ifdef blocks (GPS_DEBUG,
DEBUG_LOOP_TIMING) cost no flash and should stay visible at debug level
when their gate is enabled, rather than also requiring
MESHTASTIC_TRACE_LOGGING.

test/native-suite-count lags the two test_event_channel_* suites added
by #11045 (develop's Native Suite Count check has the same mismatch);
bump 46 -> 47.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

* gps: route GPS_DEBUG diagnostics through a LOG_DEBUG_GPS() macro (#11414)

Replaces 27 log-only #ifdef GPS_DEBUG blocks across GPS.cpp,
PositionModule, MeshService, and GPSStatus.h with a single-line
LOG_DEBUG_GPS() call (src/gps/GPSLog.h, modeled on LOG_MIGRATION:
value-gated, ((void)0) when off). Blocks containing declarations,
control flow, hexDump, or nested conditionals keep an explicit
'#if GPS_DEBUG' guard. RTC.cpp's per-reading raw time dumps and
per-candidate rejection chatter fold under the same gate; quality
transitions and boot-time seeding stay at debug.

Also fixes the '// define GPS_DEBUG' missing-# typo in two variant
headers and updates all seven commented examples to the value form
('#define GPS_DEBUG 1') required by the value-based gate.


Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

Co-authored-by: Claude <noreply@anthropic.com>

* gps: declare RTC gmtime result as pointer to const (cppcheck)

With the setTime debug dump gated behind GPS_DEBUG, all remaining uses
of t are reads; cppcheck (constVariablePointer) now flags it.

Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-08-12 00:05:51 +00:00
Jonathan Bennett fd8ba4fa4e Chop down tft-related loooong ifdefs chains (#10803)
* Chop down tft-related loooong ifdefs chains

* Fix accidental sweep-up of portduino into screen #ifdef refactor
2026-06-29 21:23:25 -05:00
a541957480 ESP32: Migrate to Arduino 3.x (pioarduino) (#9122)
* Migrate esp32 families to pioarduino platform

* ESP32c6 align text.handler_execute same as C3

* Use pioarduino `develop`

The latest fixes and the latest bugs!

* preliminary esp32p4.ini

* pioarduino: Update LovyanGFX

Includes Manuel's recent commit

* pioarduino 3.3.6

* pioarduino 3.3.6 *release*

chasing the release

* pioarduino: Fix OG ESP32 duplicate libs

* pioarduino: T-Beam 1W CDC mode

* pioarduino: disable network provisioning (wifiprov)

* pioarduino: use legacy esptoolpy naming (forward-compatible)

* Update lovyangfx from `develop` commit to 1.2.19

* fix esp32p4.ini

* check for esp32 w/ wifi

* esp32-p4 specific adaptations

* Switch to meshtastic/esp32_https_server fork (idf5 branch)

* don't ignore esp_lcd

* config for MUI

* fix/workaround SDMMC

* revert a6f6175, update to 3.3.8

* enable esp_hosted for esp32-p4 (experimental)

* Pioarduino 55.03.38-1

* NimBLE-Arduino -> Arduino "BLE" (3.3.x) migration (#10164)

* NimBLE-Arduino -> Arduino "BLE" (3.3.x) migration

* More NimBLE

* Fix Device Name in ATT Read Request (0x2A00).

Device Name is exposed in two places:

- Advertisement data: this is set properly in startAdvertising.
- GATT attribute Device Name (0x2A00). This one is handled internally in NimBLE
  and comes from ble_svc_gap_device_name_set. This is set initially, but then
  BLEDevice::createServer calls ble_svc_gap_init which resets the device name.
  This causes the device to apparently "change name after pairing":

< ACL Data TX:... flags 0x00 dlen 7  #113 [hci0] 14.241149
      ATT: Read Request (0x0a) len 2
        Handle: 0x0003 Type: Device Name (0x2a00)
> ACL Data RX: Handle 2048 flags 0x02 dlen 11             #115 [hci0] 14.269050
      ATT: Read Response (0x0b) len 6
        Value[6]: 6e696d626c65   # "nimble"

Workaround this by setting the device name once again after
BLEDevice::createServer.

* Temporarily lower CORE_DEBUG_LEVEL to INFO to avoid triggering an apparent ESP-IDF Bluetooth bug when re-connecting to Pixel 8 Android devices.

Initial pairing works, but after ESP32 is rebooted, phone fails to reconnect. Meshtastic app shows it as disconnecting immediately. LightBlue shows a more detailed error "Peripheral Connection - Warning: onConnectionStatusChange: status 61" (0x3D - MIC Failure).

Bug report to Espresssif: https://github.com/espressif/esp-idf/issues/18126#issuecomment-4286197744

* Temporarily disable ble_gap_set_data_len, causes crash with Pixel 8 Android reconnect.

Crash looks like this:
  [ 11966][E][BLEAdvertising.cpp:341] setScanResponseData(): ble_gap_adv_rsp_set_data: 22
  [ 11975][E][BLEAdvertising.cpp:1554] start(): Host reset, wait for sync.
  ERROR | ??:??:?? 11 BLE failed to start advertising
  Guru Meditation Error: Core  0 panic'ed (LoadProhibited). Exception was unhandled.

  Core  0 register dump:
  PC      : 0x420e6190  PS      : 0x00060730  A0      : 0x820e158b  A1      : 0x3fce50c0
  A2      : 0x00000000  A3      : 0x3fcb8600  A4      : 0x3fcb85cc  A5      : 0x00000000
  A6      : 0x00000000  A7      : 0x00000c03  A8      : 0x00000000  A9      : 0x3fce50b0
  A10     : 0x0000000e  A11     : 0x00000000  A12     : 0x00000010  A13     : 0x3fce50e0
  A14     : 0x00000c03  A15     : 0x00000001  SAR     : 0x0000001e  EXCCAUSE: 0x0000001c
  EXCVADDR: 0x00000000  LBEG    : 0x400570e8  LEND    : 0x400570f3  LCOUNT  : 0x00000000

  Backtrace: 0x420e618d:0x3fce50c0 0x420e1588:0x3fce5110 0x420dfe87:0x3fce5200 0x420dfefb:0x3fce5220 0x420dff3f:0x3fce5240 0x4219602b:0x3fce5260 0x4037b0e5:0x3fce5280 0x4201edf3:0x3fce52a0

Connection seems fast enough even without this. We'll investigate the
reason for the crash and re-enable once it's safe.

---------

Co-authored-by: Catalin Patulea <cronos586@gmail.com>

* Add extension from pioarduino nag
"Jason2866.esp-decoder"

* Cleanup after merge

* ESP32: Disable classic bluetooth

* Cleanup: Fix ADC channels on new variants

* InkHUD: Fix type casting for message size in saveToFlash method

inkhud compiles again!

* update p4 esp_hosted for BT

* I thought I fixed this

* fix linker error using response file (p4 only)

* fix infinite loop

* Fix Power.cpp check warning

Local variable 'config' shadows outer variable [shadowVariable]

* Build ESP32 original with NimBLE ('custom_sdkconfig' approach). (#10235)

* Re-enable littlefs json manifest

This works locally again :)
Not sure what changed

* Re-add tool-mklittlefs

* sensecap indicator fixes after upgrade arduino-esp & lovyanGFX libs

* hackaday fix

* robot tbeam cache error fix

Co-authored-by: Copilot <copilot@github.com>

* trunk fmt

* ignore trunk

* BLEDevice::deinit() added

Co-authored-by: Copilot <copilot@github.com>

* platformio-custom: Modify mtjson target dependency to prevent fake-success. (#10291)

Co-authored-by: Copilot <copilot@github.com>

* Fix ESP32-C6 linker errors.

Align .text.handler_execute section to 4 bytes and update watchdog timer core mask configuration

Co-authored-by: Copilot <copilot@github.com>

* tlora-c6: Disable Screen

MESHTASTIC_EXCLUDE_SCREEN=1 on tlora-c6.

It doesn't have a screen, and this gets it compiling again (saving flash).

* Use mverch's iram_memset hack for all OG-ESP32

* Refactor watchdog timer initialization and handling

* use adc_channel_t in variant.h

* Fix variant headers

* More idiomatic default ethernet that doesn't break the build

* Elecrows: Delete problematic variant.cpp

Not needed after USE_ETHERNET_DEFAULT

---------

Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Co-authored-by: Catalin Patulea <cronos586@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
2026-05-17 18:53:32 -05:00
Jonathan Bennett 2361776992 Rename LED_PIN to LED_POWER, move handling out of main to dedicated module (#9512)
* Rename LED_PIN to LED_POWER, move handling out of main to dedicated module

* Misc

* Remove errant endif
2026-02-05 05:41:00 -06:00
Jonathan Bennett 45fbc0f9d3 Remove stale variant.h defines (#9470)
* Remove noop CANNED_MESSAGE_MODULE_ENABLE define

* Remove over-eager warning removal

* Remove unused LED_CONN

* Dead defines removal

* Rename oddball LED pin name

* Rename second oddball LED pin name

* Remove another dead define
2026-01-29 10:58:06 -06:00
Jonathan Bennett a2e8e232f1 Remove the unused OCV_ARRAYs and move one to a variant.h (#9442) 2026-01-26 16:58:16 -06:00
Jorropo beb268ff25 Revert "add a .clang-format file (#9154)" (#9172)
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.

I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.

I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.

This reverts commit 0d11331d18.
2026-01-04 05:15:53 -06:00
Jorropo 0d11331d18 add a .clang-format file (#9154) 2026-01-03 14:19:24 -06:00
859ae4d3d2 Plain RAK4631 should not compile EInk and TFT display code (#8811)
* Plain RAK4631 should not compile EInk and TFT display code

* Add USE_TFTDISPLAY to variant files.

* Derp

* Undo the platformio.ini changes to heltec_v4

* Drop unneeded src_filter lines

---------

Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
2025-12-01 19:19:50 -06:00
HarukiToredaandJason P 34f8300288 Initial Chatter 2.0 fix for baseUI (#8615)
* Initial Chatter 2.0 fix for baseUI

* trunk fix

---------

Co-authored-by: Jason P <applewiz@mac.com>
2025-11-30 21:32:51 -06:00
Austin 974741a366 ESP32: Initial sort variants by platform (#7340) 2025-07-19 18:41:59 -05:00