* indicator: RP2040 peripherals for the main firmware
The SenseCAP Indicator RP2040 co-processor serves as a generic
peripheral bridge over a serial protobuf link (interdevice.proto):
- FakeI2C implements TwoWire and tunnels write and read transactions,
so the standard sensor drivers and the I2C scan work unmodified on
the bridged second bus (WIRE1)
- FakeUART forwards GPS NMEA to the regular GPS driver
- SD card access with chunked file transfers, paged directory
listings and card statistics; device-ui loads map tiles and map
styles from the card behind the RP2040
- link at 2M baud with 4KB chunks, message structs kept off task
stacks
Log messages carrying their own bracket tag render it like a thread
name. Replaces the earlier IndicatorSensor/COBS approach.
* indicator: address review
Correlate responses with request ids, serialize the shared TX buffer,
reject oversized frames, fix RX buffer overflow and NMEA truncation,
full-length file paths.
* indicator: assign the GPS FakeUART at runtime
Static initialization order across translation units is undefined,
so createGps() assigns and null-checks the bridged serial instead.
Bound the NMEA length defensively.
* indicator: bump device-ui pin to 27e6c0c
* indicator: ping/pong link probe, non-blocking runOnce, FakeI2C locking
The RP2040 sends nothing unsolicited without a GPS module attached, so
wait_ready now probes with the new ping message instead of listening
passively. runOnce skips its pump while a requester holds link_lock,
keeping the main loop from blocking for a full request timeout. FakeI2C
serializes transactions between the UI task and the main loop with an
owner-tracked lock held from beginTransmission to transaction end.
* indicator: link resync, config-honoring GPS, bridged-bus routing, stats validity
Frame resync scans to the next magic instead of flushing the RX buffer,
and the pump handles all buffered frames per pass. The RX drain reads in
bulk and the protobuf encoder gets the correct buffer bound. GPS honors
the gps_mode setting on the Indicator instead of always running. RTC,
I2C keyboard and motion sensor drivers resolve WIRE1 through
ScanI2CTwoWire::fetchI2CBus so bridged buses reach the right transport.
FakeUART implements flush/availableForWrite/const-write from the Stream
contract and fences its cross-core ring buffer. SdCardInfo.stats_valid
is passed through to device-ui, and the remote FS backend gains the
remove operation used for cleanup of failed tile saves.
* indicator: retry lost link round trips, I2CResult UNSPECIFIED
Remote FS operations retry once on a transport timeout. Correlation ids
drop late responses of the first attempt; a retried append whose first
attempt landed is recognized by the offset conflict carrying the
resulting file size. Definitive failures are not retried, missing-tile
probes stay a single round trip. Regenerated bindings add the
I2CResult.Status UNSPECIFIED zero value so an empty result cannot
decode as success.
* indicator: nack responses, rename bridge classes to I2CProxy/UARTProxy
A request the co-processor cannot decode or handle is nacked, so the
requester fails fast instead of burning its timeout. All requests stage
the shared tx_message under link_lock. FakeI2C and FakeUART are renamed
to I2CProxy and UARTProxy after the pattern they implement, with their
instances following suit. Drops dead code (unused NO_NEWS_PAUSE,
unreachable not-running branches, doubled include guards) and the GPS
pin log line that is meaningless on the tunneled port.
* indicator: refuse a co-processor that speaks another protocol version
The ping/pong handshake now carries InterdeviceVersion. A pong reporting
a version other than ours means the RP2040 runs firmware that does not
match this build, so the bridge stays shut down for the session and the
mismatch is logged with both versions. Requests fail fast instead of
being misinterpreted by the other side.
* indicator: regen protos, interdevice protocol version 2
* indicator: per-task I2C contexts, gated handshake, retryable link failures
The bridged I2C bus is shared between the main loop and the UI task, and
TwoWire has no transaction bracket a lock can span: drivers drain the read
buffer with available()/read() long after requestFrom() returned. Each
calling task therefore gets its own staging and read buffers instead of a
lock that could be left held (or that could not protect the read buffer
anyway). The transaction is staged inside the link, under its lock.
No request is sent before the co-processor has completed the version
handshake, and runOnce keeps probing until it does, so a co-processor that
boots slowly or reboots on its watchdog no longer leaves the bridge dead
for the session. Requests in flight are counted, not flagged: two threads
can be in a request and the first one out must not clear the other's state.
File operations are retried on a lost frame and on a co-processor busy with
card maintenance, but not on a refusal (nack) or a definitive failure, and
they release the SPI lock while they wait so a slow link does not starve
the radio.
* indicator: fail safe on a peer mismatch, wait out card maintenance
FileStatus moved to a fresh tag: reusing the tag of the removed success flag
made every failure status decode as success on a peer that predates it.
A card being mounted (busy) is retried rather than reported as an empty
slot, and a co-processor busy with card maintenance is waited out: mounting
takes seconds and the free space scan of a large card walks its whole FAT,
which is not a reason to report a missing tile. The bridged I2C bus releases
the SPI lock as well, so the keyboard scan on the UI task cannot starve the
radio either. Slot claims in the I2C proxy are atomic, NMEA is not sent to a
peer we refuse to talk to, and the handshake is completed by the unsolicited
ping the co-processor sends when it has booted, which also reports a
reboot.
* indicator: regen protos, FileStatus back on the original tags
* indicator: regen protos, ping/pong carry the InterdeviceVersion enum
* indicator: point the protobufs submodule at the merged interdevice protos
* indicator: pin device-ui to the branch with the remote SD support
* indicator: honor the txOnly flag of flush, report dropped GPS writes
flush() through a Stream pointer discarded the receive buffer: the flag is
txOnly, and HardwareSerial::flush() keeps what has been received. write()
reported bytes as written even when the link refused to send them. The link
probe uses Throttle for its rate limit.
* indicator: decide the log tag on the formatted message, hex request ids
The thread tag was suppressed based on the printf template, which disagrees
with the rendered message it is compared against: a format starting with a
conversion could produce two tags, and one without a trailing bracket-space
lost the tag entirely. vprintf now receives the thread name and picks. Also
shifts only the bytes actually buffered after a frame, throttles with
Throttle and logs request ids as hex.
* indicator: SD mount, eject and format commands over the link
* indicator: bound how long a busy card state blocks the UI task
* indicator: a busy co-processor must not block the UI task for ever
The busy retry re-armed its own budget on every busy answer, so a
co-processor that stayed busy kept the caller in the loop with no way out.
Transport retries and the wait for a busy card are now separate budgets that
only count down.
* indicator: start each request from an aligned receive buffer
A byte run lost mid-response (a UART overflow during a 4KB tile chunk, when
the display starves the RX interrupt) misaligns the assembly buffer. The
buffer was never reset, so the poison outlived the request and cascaded into
the following chunks of the same tile: one glitch dropped a whole multi-chunk
tile, while single-chunk tiles resynced in the idle gap and survived. Each
request now flushes the buffer first, bounding a glitch to the one chunk it
hit. Adds resync/decode/timeout counters, logged rarely, to see the rate.
* indicator: enlarge the LVGL heap for low-zoom map tiles
The heap was 3MB and the image cache reserves 1.5MB of it, so a low-zoom map
tile could not find a large enough contiguous block to decode and rendered
white. 5MB of the 8MB PSRAM fixes it with room to spare.
* indicator: advance the device-ui and protobufs pins to the merged commits
Point the protobufs submodule at the merged SD command protos (protobufs
#986) so it matches the checked in interdevice sources, and bump the
device-ui archive to the current indicator branch tip that carries the SD
button and format UI.
* Update device-ui library dependency URL
* remove cutom sdkconfig
* remove duplicated synchronisation (after PR11278 is in place)
* set commit reference to updated RemoteSDService class
* Add board_level configuration for release
* fix cppcheck errors
---------
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
Co-authored-by: CodeRabbit <noreply@coderabbit.ai>
Co-authored-by: mverch67 <manuel.verch@gmx.de>
* Update ESP8266Audio dependency to Meshtastic fork for compatibility
* Update ESP8266Audio dependency to Meshtastic fork for compatibility across multiple platformio.ini files
* Migrate all of the Meshtastic API attributes into the ini as a source of truth
* Cleanup garbage coalescing
* Another spot
* We already account for inkhud and mui
* Consolidate
* Removed them
* Boogers
* Infer
* Copying manifest should always succeed
* Remove portduino guards
* Rename
* None
Manuel