* Remove proprietary Bosch BSEC blob; open in-tree IAQ estimator for BME680
BSEC2 cost ~37-39 KB flash and ~4-5 KB static RAM on ~190 of ~240 build
targets, linked whether or not a BME680 was attached, and was a no-source
proprietary archive inside GPLv3 release binaries. The firmware consumed
exactly one BSEC-exclusive output: the IAQ value.
- New BME680IaqEstimator: clean-room log-domain baseline tracker
(humidity-compensated gas resistance vs a rise-fast/decay-slow ceiling,
0-500 scale matching the existing UI bands), pure math, unit-tested on
native (test_bme680_iaq, 15 tests incl. a deep-sleep reboot simulation).
Warm-up/burn-in progress persists to /prefs/bme680.dat via SafeFile so
one-sample-per-wake SENSOR nodes converge across reboots; stale
/prefs/bsec.dat is removed once.
- BME680Sensor: single-path rewrite on Adafruit_BME680 with async
once-per-minute sampling (~20x lower heater duty than BSEC LP mode),
a hard 2-minute publish-freshness bound (a dead sensor stops reporting
instead of freezing its last reading on the wire), and suppression of
bogus gas_resistance=0 points from heater-unstable cycles.
- platformio.ini: environmental_extra_common/_extra/_no_bsec collapsed
into one section; Bosch BSEC2 + BME68x deps deleted; per-variant BSEC
link-path hacks and the TEMPORARY promicro lib_ignore removed.
nrf52_promicro_diy_tcxo regains BME680 support at 36 KB clear of the
warm-store cap; rak4631 lands at 75 KB clear.
- EnvironmentTelemetry: iaq rendering gates on has_iaq (a genuine IAQ of
0 now displays); stale BSEC comments rewritten.
- rak4631 size budgets tightened (113000->108000 RAM, 786000->746000
flash) to lock in the reclaimed headroom.
- bin/bme680_iaq_replay.cpp: host-side replay harness for tuning the
estimator against captured BSEC traces (mean abs error + band
agreement), no reflashing needed.
Measured (develop -> this branch): rak4631 -38.8 KB flash / -4.9 KB RAM;
heltec-v3 -36.4 KB / -4.0 KB; tlora-v2-1-1_6 +1.3 KB (its IAQ
approximation had been dead code since #9663 due to an inverted isfinite
check and now actually runs).
Note: gas_resistance stays kOhm on the wire for fleet compatibility; the
proto comment claiming MOhm gets a separate meshtastic/protobufs docs PR.
* Address CodeRabbit review feedback
- Use Throttle::isWithinTimespanMs for all elapsed-time predicates in
BME680Sensor per coding guidelines (deadline math for the async reading
completion stays raw, as it targets an absolute timestamp)
- Make the state file name members static constexpr
- Replay tool: cast uint16_t before %u (default argument promotion), report
malformed input lines instead of silently skipping, and fail non-zero on
stream read errors
* Address CodeRabbit nitpicks
- Replace the local clampf helper with std::clamp (meshUtils.h's clamp drags
in Arduino.h, which would break the estimator's standalone host build that
the replay harness depends on)
- Trim the replay tool's file header to a two-line summary; the full build,
capture, and tuning workflow moves to docs/bme680_iaq_replay.md
* Just set LED_BUILTIN universally to -1, as we don't use it.
* LUD_BUILTIN workarounds
* Squash the LED_BUILTINs that sneaked in
* Don't kill valid pin derfine
* Migrate all of the Meshtastic API attributes into the ini as a source of truth
* Cleanup garbage coalescing
* Another spot
* We already account for inkhud and mui
* Consolidate
* Removed them
* Boogers
* Infer
* Copying manifest should always succeed
* Remove portduino guards
* Rename
* None
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
Ben Meadors