* stm32wl: add hardware RTC support infrastructure
Wires the STM32WL chip's internal RTC (running off the LSE 32.768kHz
crystal) into meshtastic's existing time-of-day framework
(perhapsSetRTC()/readFromRTC()), following the same pattern already
used for I2C RTC chips (RV3028, PCF8563/85063, RX8130CE).
LSE is started and polled manually before ever calling into the
STM32RTC library, with our own bounded timeout - the library's own
internal LSE startup path has no bounded fallback and hangs forever
via Error_Handler() if the crystal never locks, so this is required
for a board with a missing/faulty crystal to boot normally rather
than hang.
Gated behind a new HAS_LSE variant flag (currently unset everywhere,
so this is inert until a variant opts in - see follow-up commit).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* gps: qualify RTC.h includes to avoid case-insensitive filesystem collision with STM32RTC
The stm32duino STM32RTC library (added to lib_deps in a follow-up
commit) ships its own src/rtc.h. On case-insensitive filesystems
(the macOS default), an unqualified #include "RTC.h"/<RTC.h> from
any file outside src/gps/ resolves to the library's rtc.h instead of
src/gps/RTC.h, since PlatformIO's LDF puts lib_deps include paths
ahead of the project's own -Isrc/gps.
Qualify every include as gps/RTC.h so it can't collide with any
same-named header a future dependency might ship, regardless of
filesystem case sensitivity. Purely mechanical, no behavior change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl(rak3172): enable hardware RTC support
Opts rak3172 into the HAS_LSE infrastructure added previously: sets
STM32WL_LSE_DRIVE to a conservative default and pulls in the
STM32RTC library. rak3172 has ~63KB flash headroom going in;
build-verified at 76.7% flash usage after this change (up from a
73.8% baseline), well within budget.
wio-e5 is not opted in here despite sharing the same STM32WLE5 chip
- it's already at 96.8% flash usage today (GPS + I2C sensor support
compiled in, unlike rak3172), leaving too little headroom to safely
add STM32RTC without first trimming something else.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: add docstrings for LSE/RTC setup functions
Addresses CodeRabbit's docstring coverage check on PR #10961.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: address CodeRabbit nitpicks on PR #10961
- Brace the single-statement HAS_LSE branch in perhapsSetRTC() to
match the sibling readFromRTC() branch's style.
- Quote the RTC.h include in PhoneAPI.cpp for consistency with every
other qualified include site.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* add noise floor
* Sliding window noise floor
* Add getCurrentRSSI() to SimRadio for noise floor support
* Remove sendLocalStatsToPhone call from runOnce
* Change noise floor to int32_t type
* Use int32_t for RSSI sample storage in noise floor
* Remove float cast from noise floor assignment
* Fix Copilot review issues: fix noise floor logic, types, and null pointer
- Use robust busyTx/busyRx checks instead of simple isReceiving check
- Initialize noiseFloorSamples to NOISE_FLOOR_MIN instead of 0
- Move noise_floor assignment inside null check to prevent potential crash
- Change getNoiseFloor() and getAverageNoiseFloor() to return int32_t
- Fix RSSI validation to check for positive values (rssi > 0)
- Fix format specifier from %.1f to %d for int32_t
- Update comments to accurately reflect the sampling logic
* Fix RSSI condition to include zero value
* Change noise floor initialization to zero
* Disable noise floor for LR11x0 chips: getRSSI(bool) unsupported
* Remove updateNoiseFloor call from onNotify to avoid radio queue overflow
Per PR review feedback, calling updateNoiseFloor() in onNotify() for every
ISR event (ISR_TX, ISR_RX, TRANSMIT_DELAY_COMPLETED) can cause the LoRa
radio queue to get full. The noise floor sampling still happens in
startReceive() and after transmitting.
* fix lr11x0 current rssi
* Address noise floor review comments
* Address Copilot SimRadio noise floor comments
* Fix RadioLibInterface formatting
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* fix(telemetry): stop emitting -0.001V sentinel when battery unavailable (#7958)
* address review: use int32_t for batteryMv to avoid uint16_t signed wrap
* Enable Lite and Narrow regions and introduce getEffectiveDutyCycle for Lite profiles
* Add TrafficType enum and extend getConfiguredOrDefaultMsScaled to manage based on regionProfile settings
* Refactor telemetry modules to include TrafficType in getConfiguredOrDefaultMsScaled calls
* Update submodule protobufs to latest commit
* Add support for new region presets and modem presets in menu options
* Add new LoRa region codes and modem presets for EU bands
* boof
* Add modem presets for LITE and NARROW configurations
* Update subproject commit reference in protobufs
* Update protobufs
* Refactor modem preset definitions to use macro for consistency and clarity
* Refactor modem preset cases to use PRESET macro for consistency
* fix: update LoRa region code for EU 868 narrowband configuration
Co-authored-by: Copilot <copilot@github.com>
* Fix test suite failure
Co-authored-by: Copilot <copilot@github.com>
* Add override slot override - for when one override isn't enough.
Co-authored-by: Copilot <copilot@github.com>
* address copilot comments
---------
Co-authored-by: Copilot <copilot@github.com>
* Add transmit history for throttling that persists between reboots
* Fix RAK long press detection to prevent phantom shutdowns from floating pins
* Update test/test_transmit_history/test_main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Test fixes and placeholder for content handler tests
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Align telemetry broadcast want_response behavior with traceroute
* Fixes
* Reduce side-effects by making the telemetry modules handle the ignorerequest
* Remove unnecessary ignoreRequest flag
* Try inheriting from MeshModule
* Add exclusion for sensor/router roles and add base telem module
* treewide: make 'ifdef DEBUG_PORT' guards also take into account DEBUG_MUTE
* stm32wl: Add a guard against having debug prints turned on without PIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF defined
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* First addition of __has_include for sensor support
* Add __has_include blocks for sensors
* Put BMP and BME back in the right sensors
* Make TelemetrySensor::setup() a pure virtual finction
* Split environmental_base to environmental_extra, to compile the working sensor libs for Native
* Remove hard-coded checks for ARCH_PORTDUINO
* Un-clobber bmx160
* Move BusIO to environmental_extra due to Armv7 compile error
* Move to forked BusIO for the moment
* Enable HAS_SENSOR for Portduino
* Move back to Adafruit BusIO after patch
* Clean up SimRadio and don't let it use PKC
* Add collision emulation for SimRadio
* Add stats from SimRadio to LocalStats
* Make emulating collisions optional
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Make SPI frequency configurable on Native
* Make the tophone queue size configurable for Portduino
* The modified SPISettings must be configured in setup(), after config.yaml is processed
* make MeshService a pointer, so we can configure MAX_RX_TOPHONE at run time
* Got a little over excited with refactoring
* Silence a warning
* Add congestion scaling coefficient
* Added active mesh sized based interval scaling
* Moved back to bottom
* Format
* Add observers and use correct number of online nodes
* Implement replies for all telemetry types based on variant tag
* Remove check for `ignoreRequest`: modules can set this, don't need to check
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add MaxNodes to Native
* It compiles...
* Convert nodedb to use new
* Closer but still broken.
* Finally working
* Remove unintended lines
* Don't include a pointer
* Capitalization matters.
* avoid rename in protocol regen
* When trimming the nodeDB, start with a cleanup
* Remove extra cleanupMeshDB() call for now
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* For Garth
* Push it real good
* Wut
* Double tap
* Move disable logic
* Actually return
* Reinitialize setClick in thread body
* Initialize later so that we actually have nodedb on init
* Fixes
