* stm32wl: add hardware RTC support infrastructure
Wires the STM32WL chip's internal RTC (running off the LSE 32.768kHz
crystal) into meshtastic's existing time-of-day framework
(perhapsSetRTC()/readFromRTC()), following the same pattern already
used for I2C RTC chips (RV3028, PCF8563/85063, RX8130CE).
LSE is started and polled manually before ever calling into the
STM32RTC library, with our own bounded timeout - the library's own
internal LSE startup path has no bounded fallback and hangs forever
via Error_Handler() if the crystal never locks, so this is required
for a board with a missing/faulty crystal to boot normally rather
than hang.
Gated behind a new HAS_LSE variant flag (currently unset everywhere,
so this is inert until a variant opts in - see follow-up commit).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* gps: qualify RTC.h includes to avoid case-insensitive filesystem collision with STM32RTC
The stm32duino STM32RTC library (added to lib_deps in a follow-up
commit) ships its own src/rtc.h. On case-insensitive filesystems
(the macOS default), an unqualified #include "RTC.h"/<RTC.h> from
any file outside src/gps/ resolves to the library's rtc.h instead of
src/gps/RTC.h, since PlatformIO's LDF puts lib_deps include paths
ahead of the project's own -Isrc/gps.
Qualify every include as gps/RTC.h so it can't collide with any
same-named header a future dependency might ship, regardless of
filesystem case sensitivity. Purely mechanical, no behavior change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl(rak3172): enable hardware RTC support
Opts rak3172 into the HAS_LSE infrastructure added previously: sets
STM32WL_LSE_DRIVE to a conservative default and pulls in the
STM32RTC library. rak3172 has ~63KB flash headroom going in;
build-verified at 76.7% flash usage after this change (up from a
73.8% baseline), well within budget.
wio-e5 is not opted in here despite sharing the same STM32WLE5 chip
- it's already at 96.8% flash usage today (GPS + I2C sensor support
compiled in, unlike rak3172), leaving too little headroom to safely
add STM32RTC without first trimming something else.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: add docstrings for LSE/RTC setup functions
Addresses CodeRabbit's docstring coverage check on PR #10961.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: address CodeRabbit nitpicks on PR #10961
- Brace the single-statement HAS_LSE branch in perhapsSetRTC() to
match the sibling readFromRTC() branch's style.
- Quote the RTC.h include in PhoneAPI.cpp for consistency with every
other qualified include site.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add define for screen I2C frequency
* Add functions to get I2C screen frequency and port
* Make reclock function aware of screen-set I2C speeds
* Refurbish ReClockI2C API
* Make ReClockI2C API class
* Use new API in AirQualityTelemetry module
* Minor changes on some logs
* Update esp8266-oled library
* Fix esp8266 library
* Minor logging changes
* Improve setClock and restoreClock cases
* Make getter functions const, fix capitalisaiton of new functions
* Minor typo, remove pragma once
* Low prio debug fixes
* Mark getter functions as const (properly)
* Fix LOG based on coderabbit feedback
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Fix trunk
* Fix on condition in reclock
* Add check on polling interval of sen5x
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
