* stm32wl: add hardware RTC support infrastructure
Wires the STM32WL chip's internal RTC (running off the LSE 32.768kHz
crystal) into meshtastic's existing time-of-day framework
(perhapsSetRTC()/readFromRTC()), following the same pattern already
used for I2C RTC chips (RV3028, PCF8563/85063, RX8130CE).
LSE is started and polled manually before ever calling into the
STM32RTC library, with our own bounded timeout - the library's own
internal LSE startup path has no bounded fallback and hangs forever
via Error_Handler() if the crystal never locks, so this is required
for a board with a missing/faulty crystal to boot normally rather
than hang.
Gated behind a new HAS_LSE variant flag (currently unset everywhere,
so this is inert until a variant opts in - see follow-up commit).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* gps: qualify RTC.h includes to avoid case-insensitive filesystem collision with STM32RTC
The stm32duino STM32RTC library (added to lib_deps in a follow-up
commit) ships its own src/rtc.h. On case-insensitive filesystems
(the macOS default), an unqualified #include "RTC.h"/<RTC.h> from
any file outside src/gps/ resolves to the library's rtc.h instead of
src/gps/RTC.h, since PlatformIO's LDF puts lib_deps include paths
ahead of the project's own -Isrc/gps.
Qualify every include as gps/RTC.h so it can't collide with any
same-named header a future dependency might ship, regardless of
filesystem case sensitivity. Purely mechanical, no behavior change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl(rak3172): enable hardware RTC support
Opts rak3172 into the HAS_LSE infrastructure added previously: sets
STM32WL_LSE_DRIVE to a conservative default and pulls in the
STM32RTC library. rak3172 has ~63KB flash headroom going in;
build-verified at 76.7% flash usage after this change (up from a
73.8% baseline), well within budget.
wio-e5 is not opted in here despite sharing the same STM32WLE5 chip
- it's already at 96.8% flash usage today (GPS + I2C sensor support
compiled in, unlike rak3172), leaving too little headroom to safely
add STM32RTC without first trimming something else.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: add docstrings for LSE/RTC setup functions
Addresses CodeRabbit's docstring coverage check on PR #10961.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: address CodeRabbit nitpicks on PR #10961
- Brace the single-statement HAS_LSE branch in perhapsSetRTC() to
match the sibling readFromRTC() branch's style.
- Quote the RTC.h include in PhoneAPI.cpp for consistency with every
other qualified include site.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Refactor and consolidate windowing logic
* Trunk
* Fixes
* More
* Fix braces and remove unused now variables.
There was a brace in src/mesh/RadioLibInterface.cpp that was breaking
compile on some architectures.
Additionally, there were some brace errors in
src/modules/Telemetry/AirQualityTelemetry.cpp
src/modules/Telemetry/EnvironmentTelemetry.cpp
src/mesh/wifi/WiFiAPClient.cpp
Move throttle include in WifiAPClient.cpp to top.
Add Default.h to sleep.cpp
rest of files just remove unused now variables.
* Remove a couple more meows
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* for #4154 and #4136 add concept of dependent gpios...
Which is currently only tested with the LED but eventually
will be used for shared GPIO/screen power rail enable
and LED forcing (which is a sanity check in the power stress
testing)
* fix linter warning
* Transformer is a better name for the LED input > operation > output classes
* PMW led changes to work on esp32-s3
* power stress improvements
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
* fix gpio transformer stuff to work correctly with LED_INVERTED
Thanks @todd-herbert for noticing this and the great stack trace.
The root cause was that I had accidentially shadowed outPin in a subclass
with an unneeded override. It would break on any board that had inverted
LED power.
fixes
https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
* Support driving multiple output gpios from one input.
While investigating https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
I noticed in variant.h that there are now apparently newer TBEAMs than mine
that have _both_ a GPIO based power LED and the PMU based LED. Add a splitter
so that we can drive two output GPIOs from one logical signal.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
