* logging: strip redundant punctuation, level prefixes, and 'successfully' from log strings
The logger already appends a newline and prints the level tag, so
trailing '.', '!', '...', literal \n, and 'Error:'/'Warning:' prefixes
inside format strings are wasted flash bytes. Same for 'successfully'
(the affirmative form already implies it).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: tighten verbose log strings in modules, radio, platform, and system code
Rewrite wordy log messages to terser equivalents - drop filler words
(articles, 'attempting', 'due to', 'please'), use 'Can't X'/'X failed'
phrasing, and abbreviate where the codebase already does (config, init,
msg, BT). Format specifiers and argument lists are unchanged; distinctive
greppable tokens are preserved.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: tighten verbose log strings in telemetry sensors and GPS
Same terseness pass: drop filler, 'Can't X'/'X failed' phrasing, common
abbreviations (temp, msg). Specifiers, arguments, and sensor-name
prefixes unchanged.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: tighten verbose log strings in mesh core
Same terseness pass over NodeDB, Router, MeshService, PhoneAPI,
RadioInterface, NextHopRouter, and PacketHistory: 'X failed'/'Can't X'
phrasing, imperative verbs, dropped filler. Specifiers and arguments
unchanged; duplicate literals kept identical to preserve linker string
dedup.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: 'Unable to/Could not/Cannot' -> "Can't" in log strings
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: clang-format rewrap after string shortening
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* logging: restore boot-logo trailing newline and progress-dot strings
The terseness pass over-trimmed: the Meshtastic ASCII boot logo kept its
blank line via a trailing \n, and three bare "." progress ticks were
reduced to empty strings.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LBiZc9sfPrH1MZ2L3Fxgt1
* Update src/mesh/wifi/WiFiAPClient.cpp
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
* logging: address review feedback on the terseness audit
- Node/packet IDs use the repo's 0x%08x convention in NextHopRouter,
NodeDB, AdminModule and CannedMessageModule. The sibling log in each
if/else pair is converted too, so a pair isn't split across two formats.
next_hop stays 0x%x - it's the last-byte relay hint, not a NodeNum.
- RTC: the read-path and set-path "not found" warnings were byte-identical,
so the linker deduped them and the log couldn't say which one fired.
Split into "RTC read:" / "RTC set:". (The four sites live in mutually
exclusive #ifdef branches, so the RTC family was never ambiguous.)
- SCD4X getAmbientPressure()/setAmbientPressure() logged "altitude", and
SCD30 getASC() logged "Can't send command" for a read. Both now name the
operation they actually perform.
- LOG_ERROR already carries the level: ". Error: %u" -> ", rc=%u" (matching
the existing rc=%d house style) and "Error executing X()" -> "X() failed".
- Typos and wording: "OTA partiton. (Reason" -> "OTA partition (reason",
"CST3530 not response ~" -> "CST3530 no response", "Packet received with
to: of 0" -> "to=0", HostMetrics "Error decoding" -> "Can't decode", and
the dangling ": " on the NextHopRouter retransmission line.
Printf specifier sequences are byte-identical on all 37 touched lines apart
from the 6 deliberate %x/%u -> %08x node-ID widenings, all on uint32_t args.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
---------
Co-authored-by: Claude <noreply@anthropic.com>
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* feat: populate MyNodeInfo.device_id on all platforms
RP2040/RP2350 use the 64-bit pico unique board id, STM32WL the 96-bit
silicon UID, ESP32-S2 joins the existing OPTIONAL_UNIQUE_ID efuse branch,
and everything else (classic ESP32 in particular) falls back to a
deterministic factory-MAC-derived id, resolving the long-standing FIXME.
Portduino keeps the config-supplied id preferred and now uses the MAC
fallback when the config omits one.
No proto or persistence changes; the id is re-read from silicon each
boot and PhoneAPI still zeroes it for unauthenticated clients.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* fix: declare zero_mac const to satisfy cppcheck
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* fix: address review feedback on device_id derivation
Clear any disk-loaded device_id before the silicon derivation so a failed
read leaves it unset rather than stale (Copilot), and size the portduino
config copy with sizeof instead of a literal 16 (CodeRabbit).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* refactor: extract device_id generation into per-arch getDeviceId()
Per review feedback on #10995: move the platform-specific
MyNodeInfo.device_id derivation out of the #if/#elif ladder in
NodeDB.cpp into a getDeviceId() interface (target_specific.h)
implemented per-architecture alongside each platform's getMacAddr():
- esp32: efuse OPTIONAL_UNIQUE_ID (C3/S2/S3/C6); classic ESP32 -> MAC
- nrf52: FICR DEVICEID + DEVICEADDR
- nrf54l15: FICR->INFO.DEVICEID + DEVICEADDR (NRF_FICR-guarded, MAC fallback)
- rp2xx0: pico_get_unique_board_id()
- stm32wl: HAL_GetUIDw0/1/2()
- portduino: config-supplied id preferred, else MAC
The shared MAC-derived fallback moves to meshUtils as
getMacAddrDeviceId(). NodeDB.cpp now zero-inits the field and makes a
single getDeviceId() call, dropping ~65 lines of platform boilerplate
plus the esp_efuse/pico/stm32 includes that came with it. No behavior
change: device_id is still re-read from silicon each boot and never
persisted.
Builds green: native-macos, tbeam, heltec-v3, rak4631, rak11310, rak3172.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
* fix: address review of device_id refactor
- getMacAddrDeviceId(): zero-init the mac[6] buffer. getMacAddr() can return
without writing (e.g. Portduino with no MAC source), so the old uninitialized
buffer let stack garbage pass the all-zeros guard and become device_id. The
pre-refactor code relied on the zero-initialized static ourMacAddr; restore
that guarantee.
- nrf54l15 getDeviceId(): drop the `#if defined(NRF_FICR)` guard and read FICR
unconditionally (as the pre-refactor NodeDB code did). The guarded #else fell
back to getMacAddr()'s hard-coded placeholder MAC, which would give every unit
an identical device_id; a missing NRF_FICR should be a loud compile error.
- NodeDB.cpp: `#include "target_specific.h"` instead of hand-copied externs for
getMacAddr/getDeviceId; retire the stale FIXME. Same for meshUtils.cpp (whose
extern comment wrongly claimed the TU was Arduino-free).
- Delete the orphaned commented-out device_id hex-dump block in NodeDB.cpp.
- Trim/de-duplicate the getDeviceId contract comments (single-sourced in
target_specific.h).
Builds green: native-macos, tbeam.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
* docs: trim device_id comments to the repo's 1-2 line guideline
Addresses CodeRabbit review nitpick on #10995: shorten the getDeviceId()
(target_specific.h), getMacAddrDeviceId() (meshUtils.h), device-id refresh
(NodeDB.cpp), and nrf54l15 getDeviceId comments to two lines each, per the
"one or two lines maximum" coding guideline. Comment-only; no behavior change.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
---------
Co-authored-by: Claude Fable 5 <noreply@anthropic.com>
* esp32: release BTDM heap when Bluetooth inactive
Release ESP-IDF BTDM memory after config load when Bluetooth is disabled or WiFi is enabled, recovering heap on ESP32 targets where BLE won’t be used for this boot.
* Address BT memory release review comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(esp32): skip RTC timer wake on user shutdown
Do not arm esp_sleep_enable_timer_wakeup when msecToWake is portMAX_DELAY (UI shutdown), matching nRF52 system_off semantics.
fix(rak_wismesh_tap_v2): Tag OCV curve and 16MB partition
Add OCV_ARRAY matching WisMesh Tag for accurate SOC. Use 16MB flash partition scheme for TAP V2 hardware.
Co-authored-by: Cursor <cursoragent@cursor.com>
* Trunkt
---------
Co-authored-by: Cursor <cursoragent@cursor.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Power off control pin on Thinknode m5 during deepsleep
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Finish HAS_RTC cleanup
* Add RTC for Thinknode M5
* Don't double-init Wire
* Specify the RTC chip directly rather than use SensorRtcHelper.
Saves a bit of flash, and avoid mis-detection
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
* Don't use assert for Lock
* Don't use assert for MQTT messages
* Split assert in getMacAddr to always run the function
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* [WIP] Base firmware pending support for 2nd button
* Update button behaviour. Still WIP
* [WIP] Base firmware pending support for 2nd button
* Update button behaviour. Still WIP
* change env to lowercase
Co-authored-by: rcarteraz <robert.l.carter2@gmail.com>
* yea - well - what else is new?
* fix secondary button behavior and update trunk
---------
Co-authored-by: rcarteraz <robert.l.carter2@gmail.com>
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update sensor drive and low power features.
* Update ST7789 TFT control logic.
* Update Heltec nRF board low power features.
* Update the GPS UART port pointer
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* for #4154 and #4136 add concept of dependent gpios...
Which is currently only tested with the LED but eventually
will be used for shared GPIO/screen power rail enable
and LED forcing (which is a sanity check in the power stress
testing)
* fix linter warning
* Transformer is a better name for the LED input > operation > output classes
* PMW led changes to work on esp32-s3
* power stress improvements
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
* fix gpio transformer stuff to work correctly with LED_INVERTED
Thanks @todd-herbert for noticing this and the great stack trace.
The root cause was that I had accidentially shadowed outPin in a subclass
with an unneeded override. It would break on any board that had inverted
LED power.
fixes
https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
* Support driving multiple output gpios from one input.
While investigating https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
I noticed in variant.h that there are now apparently newer TBEAMs than mine
that have _both_ a GPIO based power LED and the PMU based LED. Add a splitter
so that we can drive two output GPIOs from one logical signal.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix I2C pindefs
* Initial driver testing for HT-VME290
* E-Ink full refresh after canned message pop up
* Tidy variant folders
* Clean ESP32 cpuDeepSleep method
Merge sections, and remove the random assortment of gpio holds left behind.
* Enable 32kHz in variant.h
* Orient E290 with LoRa antenna facing up
* Revert "Clean ESP32 cpuDeepSleep method"
This reverts commit cb8ee508ec2d6bc27a8e228021fd1efbd034c4a0.
* Reduce deep-sleep current for VME213 (non-intrusive)
Originally I made an attempt at tidying up the cpuDeepSleep method, but have reverted that. New commit makes only the changes needed to support VME213. Don't really want the headache of breaking sleep for other variants, especially when this PR is just about implementing new boards.
* Update lib_deps; remove board_level extra
* Make sure to call randomSeed() on esp32
* Randomize the top 22 bits of the Message ID
* Make it clear that we are not calling randomSeed() on purpose
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Bump platfomio/espressif32 version to latest 6.7.0
* Fix deprecated constants
* Remove pin defs already defined by the framework
* ESP_EXT1_WAKEUP_ALL_LOW is deprecated for any target except esp32
* Enable LTO and use newlib nano flavor
* Make trunk happy
* Respect build_unflags of base env
* Recover float printfing
* Disable BLE_SM_PAIR_AUTHREQ_SC
* Distribute BLE_SM_PAIR_KEY_DIST_ID too
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add Chatter 2 default_envs
* Add Chatter 2 to varients
* Add Chatter 2 specific code to esp32 platform code
* Parameterize TFT_INVERT for Chatter 2 and specify setRotation to 1
* Fix formatting to make Trunk happy
* Remove commented out #define USE_LCC68
* Fix formatting again
* Add chatter2 to the CI matrix
---------
Co-authored-by: code8buster <20384924+code8buster@users.noreply.github.com>
* Pico W: Initial WiFi support: connects, but freezes after a while
* Update arduino-pico core to fix hang with Wi-Fi
* Add `picow` to workflow since it's different from `pico` now
This function causes the new arduino-esp32 core to revert to the pseudorandom behavior specified in Arduino.
Calls to random() automatically use esp_random() if randomSeed or useRealRandomGenerator(false) aren't called.
Tentative fix for #2357
