The send_bell append writes bytes[size] and bytes[size+1] while the guard only checked size < DATA_PAYLOAD_LEN, overrunning the 233-byte payload array by one when size == DATA_PAYLOAD_LEN - 1. Guard on size + 1.
* Null-check packet allocations in allocForSending and its callers
Sibling of 0ae44d701.
* Null-check allocDataProtobuf, allocAckNak and allocErrorResponse callers
Second tier of the same nullable contract.
* Keep telemetry sleep scheduling on allocation failure
Allocation failure now marks the telemetry invalid instead of returning
early, so power-saving SENSOR nodes still arm deep sleep.
Removed:
- MessageStore::addFromPacket and addFromString, superseded by
tryAddFromPacket
- GeoCoord rangeRadiansToMeters, distanceTo, bearingTo
- Router::rawSend, declared virtual with no override and no caller
- ContentHandler handleHotspot, handleFs, handleAdminSettings,
handleAdminSettingsApply, handleDeleteFsContent and their commented
route registrations, plus the now unreachable htmlDeleteDir and the
handleUpdateFs declaration that had no definition
- ContentHelper replaceAll
- OnScreenKeyboardModule popup chain: showPopup, clearPopup, drawPopup,
drawPopupOverlay and their state, unreachable since the frame based UI
was replaced by baseUI
- DebugRenderer drawDebugInfoTrampoline, drawDebugInfoSettingsTrampoline
and the orphaned drawFrameSettings
- NodeListRenderer calculateMaxScroll, drawColumns and a stale extern
haveGlyphs declaration with no definition
- UIRenderer::haveGlyphs, Screen::blink,
NotificationRenderer::showKeyboardMessagePopupWithTitle,
VirtualKeyboard::getInputText
- InkHUD touchNavLeft, touchNavRight, Applet::getActiveNodeCount,
ThreadedMessageApplet::saveMessagesToFlash
- TwoButton::setHandlerUp, TwoButtonExtended setHandlerUp,
setJoystickDownHandlers, setJoystickUpHandlers
- CannedMessageModule LaunchRepeatDestination, isCharInputAllowed,
hasMessages
- TrafficManagementModule resetStats, recordRouterHopPreserved,
saturatingIncrement
- UnitConversions::MetersPerSecondToMilesPerHour
- EncryptedStorage getSessionRemainingSeconds
- BMI270Sensor::writeRegisters, GPS::hasFlow, FSCommon copyFile,
SerialConsole consolePrintf, buzz playLongPressLeadUp,
memGet displayPercentHeapFree
* stm32wl: add hardware RTC support infrastructure
Wires the STM32WL chip's internal RTC (running off the LSE 32.768kHz
crystal) into meshtastic's existing time-of-day framework
(perhapsSetRTC()/readFromRTC()), following the same pattern already
used for I2C RTC chips (RV3028, PCF8563/85063, RX8130CE).
LSE is started and polled manually before ever calling into the
STM32RTC library, with our own bounded timeout - the library's own
internal LSE startup path has no bounded fallback and hangs forever
via Error_Handler() if the crystal never locks, so this is required
for a board with a missing/faulty crystal to boot normally rather
than hang.
Gated behind a new HAS_LSE variant flag (currently unset everywhere,
so this is inert until a variant opts in - see follow-up commit).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* gps: qualify RTC.h includes to avoid case-insensitive filesystem collision with STM32RTC
The stm32duino STM32RTC library (added to lib_deps in a follow-up
commit) ships its own src/rtc.h. On case-insensitive filesystems
(the macOS default), an unqualified #include "RTC.h"/<RTC.h> from
any file outside src/gps/ resolves to the library's rtc.h instead of
src/gps/RTC.h, since PlatformIO's LDF puts lib_deps include paths
ahead of the project's own -Isrc/gps.
Qualify every include as gps/RTC.h so it can't collide with any
same-named header a future dependency might ship, regardless of
filesystem case sensitivity. Purely mechanical, no behavior change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl(rak3172): enable hardware RTC support
Opts rak3172 into the HAS_LSE infrastructure added previously: sets
STM32WL_LSE_DRIVE to a conservative default and pulls in the
STM32RTC library. rak3172 has ~63KB flash headroom going in;
build-verified at 76.7% flash usage after this change (up from a
73.8% baseline), well within budget.
wio-e5 is not opted in here despite sharing the same STM32WLE5 chip
- it's already at 96.8% flash usage today (GPS + I2C sensor support
compiled in, unlike rak3172), leaving too little headroom to safely
add STM32RTC without first trimming something else.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: add docstrings for LSE/RTC setup functions
Addresses CodeRabbit's docstring coverage check on PR #10961.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: address CodeRabbit nitpicks on PR #10961
- Brace the single-statement HAS_LSE branch in perhapsSetRTC() to
match the sibling readFromRTC() branch's style.
- Quote the RTC.h include in PhoneAPI.cpp for consistency with every
other qualified include site.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Decree of the Cabinet of Ministers of Ukraine dated February 25, 2026,*
No. 262, on amendments to Section 2 of the Plan for the Allocation and
Use of the Radio Frequency Spectrum in Ukraine, has harmonised
Ukrainian regulations on the 868 MHz spectrum with the EU's, thereby
making UA_868 legally obsolete.
* https://zakon.rada.gov.ua/laws/show/262-2026-п
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Every other .cpp/.h pair in src/ (350 of 351) uses identical
capitalization between the two files. Power.cpp/power.h was the sole
outlier; this aligns it with the rest of the codebase. No functional
change — all includes already resolved this file the same way on
case-sensitive filesystems.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* clarify channel number formatting and fix the fixed-width padded nodeIDs
* use the explicit 0x%08x for packets and nodeIDs throughout
* LLM instructions
* InkHUD: map tile background, zoom controls, and GPS live tracking
- Map background tiles are now rendered on the display when available, compressed with LZ4 to keep flash usage low
- If no map tiles are loaded, the map applets behave exactly as before
- Zoom in, zoom out, and reset zoom (back to auto-fit) are accessible from the menu, and only appear when the menu is opened from a map screen
- The map updates automatically whenever GPS gets a new position or your phone shares a location
- The Positions and Favorites map applets now also refresh when mesh position packets arrive for your own node
- The Favorites map now shows your position on the map even if you have no favorites yet
* README Update
* Update MapApplet.cpp
* Zoom fixed
* Zoom with no tiles fix
* CI fix
* fix(t5s3-epaper): increase ED047TC1 margins to 16px on all sides
Tested on device — 16px uniform margins look noticeably cleaner than
the previous asymmetric 8–9px values. Canvas shrinks from 944×523 to
928×508 (H_OFFSET_BYTES=2, V_OFFSET_TOP/BOTTOM=16).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(t5s3-epaper): remove EINK_EDGE_LINES calibration diagnostic from ED047TC1
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(t5s3-epaper): align TOUCH_THRESHOLD_X with TOUCH_THRESHOLD_Y (40px)
X axis threshold was 60 while Y was 40, causing asymmetric swipe detection.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Enable Lite and Narrow regions and introduce getEffectiveDutyCycle for Lite profiles
* Add TrafficType enum and extend getConfiguredOrDefaultMsScaled to manage based on regionProfile settings
* Refactor telemetry modules to include TrafficType in getConfiguredOrDefaultMsScaled calls
* Update submodule protobufs to latest commit
* Add support for new region presets and modem presets in menu options
* Add new LoRa region codes and modem presets for EU bands
* boof
* Add modem presets for LITE and NARROW configurations
* Update subproject commit reference in protobufs
* Update protobufs
* Refactor modem preset definitions to use macro for consistency and clarity
* Refactor modem preset cases to use PRESET macro for consistency
* fix: update LoRa region code for EU 868 narrowband configuration
Co-authored-by: Copilot <copilot@github.com>
* Fix test suite failure
Co-authored-by: Copilot <copilot@github.com>
* Add override slot override - for when one override isn't enough.
Co-authored-by: Copilot <copilot@github.com>
* address copilot comments
---------
Co-authored-by: Copilot <copilot@github.com>
Marker boxes, the own-node bullseye, and the labeled-marker cross were
all hardcoded in pixels (11px box, r=8 circle, 12px cross). On the
T5S3 with a 12pt fontSmall (~17px line height) the hop-count digit
overflowed its box entirely. Sizes now derive from fontSmall.lineHeight()
so the applet renders correctly on both small (6pt) and large (12pt+)
display variants.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* niche: add InkHUD port for LilyGo T5-E-Paper-S3-Pro (ED047TC1)
Add a NicheGraphics EInk driver adapter for the 4.7" ED047TC1 parallel
e-paper display used on the T5-E-Paper-S3-Pro (H752-01). The driver
wraps FastEPD and handles the polarity difference between InkHUD's
buffer format (0xFF = white) and FastEPD's (0x00 = white).
Rewrite variants/esp32s3/t5s3_epaper/nicheGraphics.h which was an
incomplete copy of the Heltec VM-E290 setup referencing undefined SPI
pin macros and a non-existent BUTTON_PIN_SECONDARY. The board uses a
parallel display, not the small SPI DEPG0290BNS800 that was referenced.
* fix: guard inputBroker null dereference in TouchScreenImpl1::init()
When MESHTASTIC_EXCLUDE_INPUTBROKER is defined (e.g. InkHUD builds),
inputBroker is nullptr. Calling inputBroker->registerSource() in that
state caused a LoadProhibited panic on any board that has both
HAS_TOUCHSCREEN=1 and the InputBroker excluded.
Add a null check before registerSource() to prevent the crash.
* niche: fix display rotation for T5-E-Paper-S3-Pro InkHUD port
Set rotation=3 (270° CW) in nicheGraphics.h to correct for FastEPD
scanning the ED047TC1 panel in portrait orientation, resulting in
correct landscape display output.
* fix: update buffer format descriptions and remove polarity inversion for InkHUD and FastEPD
* fix: update ED047TC1 driver to handle inactive pixel borders and adjust safe-area dimensions
* fix: comment out ruler diagnostic for E-Ink driver
* feat: implement TouchInkHUDBridge for direct touch event handling in InkHUD
* niche: add FreeSans 18pt/24pt Win1253 (Greek) fonts for larger InkHUD displays
Add Win1253-encoded FreeSans 18pt and 24pt font headers to support Greek
script on larger InkHUD screens (e.g., the 4.7" ED047TC1 at ~234 DPI).
Register FREESANS_24PT_WIN1253 and FREESANS_18PT_WIN1253 macros in AppletFont.h.
Set fontLarge=24pt, fontMedium=18pt, fontSmall=12pt in nicheGraphics.h for the
T5-E-Paper-S3-Pro.
* feat(ed047tc1): use true partial update for FAST refresh
Replace fullUpdate(CLEAR_FAST) with partialUpdate() for FAST display
updates. FastEPD's partialUpdate() diffs pCurrent against pPrevious
and only applies the update waveform to rows that have changed, leaving
unchanged rows with a neutral signal.
This reduces visible flicker on routine updates (new messages, position
changes) — only the affected region of the screen refreshes. Full-screen
CLEAR_SLOW updates are preserved for periodic ghosting cleanup, driven
by InkHUD's setDisplayResilience() ratio.
* feat(t5s3-epaper): enable frontlight via LatchingBacklight
Wire up BOARD_BL_EN (GPIO11) to InkHUD's LatchingBacklight driver.
Enable the backlight menu item so users can toggle "Keep Backlight On"
via Settings. The backlight turns on automatically when the menu opens
and off when it closes.
* Fix RTC chip (PCF8563 not PCF85063) and GT911 I2C address collision
- variant.h used PCF85063_RTC but the board has a PCF8563. The difference
is the RAM register: PCF85063 has 1 byte of RAM; PCF8563 does not. The
PCF85063 driver was trying to write this register on init, failing every
time, and setDateTime writes were silently discarded — RTC time was
never persisted across reboots. Switch to PCF8563_RTC/PCF8563_INT.
Before:
[E][SensorPCF85063.hpp:375] initImpl(): Failed to write to RAM memory
register. Maybe this chip is pcf8563.
Read RTC time from PCF85063 getDateTime as 2026-04-05 00:00:23
PCF85063 setDateTime 2026-04-05 18:40:59
Read RTC time from PCF85063 getDateTime as 2026-04-05 00:00:19 ← lost
After:
PCF8563 found at address 0x51
Read RTC time from PCF8563 getDateTime as 2026-04-05 18:58:37 ← persisted
PCF8563 setDateTime 2026-04-05 18:58:44
Read RTC time from PCF8563 getDateTime as 2026-04-05 18:58:44 ← round-trips
- GT911 touch was initialized with GT911_SLAVE_ADDRESS_L (0x5D), which
collides with the SFA30 air quality sensor also at 0x5D on the same
I2C bus. Switch to GT911_SLAVE_ADDRESS_H (0x14): the library drives
INT high during reset to program the GT911 to address 0x14,
eliminating the address conflict.
Before:
SFA30 found at address 0x5d
[I][TouchDrvGT911.hpp:568] initImpl(): Try using 0x5D as the device address
After:
SFA30 found at address 0x5d
[I][TouchDrvGT911.hpp:544] initImpl(): Try using 0x14 as the device address
* t5s3_epaper: fix GT911 ghost-SFA30 via early I2C address latch
Investigation findings
----------------------
Boot logs showed "SFA30 found at address 0x5d" on every cold power-on,
and AirQualityTelemetry was registering an SFA30 sensor. However, every
readMeasuredValues() call returned error 268 (0x010C = Sensirion
WriteError | I2cAddressNack), meaning the I2C write to 0x5D was being
NACK'd — inconsistent with a real SFA30.
Root cause: the GT911 touch controller latches its I2C address from the
INT pin level at reset time (GT911 datasheet §4.3). GPIO3 (INT) defaults
LOW on ESP32-S3 cold boot → GT911 always powers up at 0x5D
(SLAVE_ADDRESS_L). The I2C scanner runs before lateInitVariant() had a
chance to reprogram the chip.
The scanner's SFA30 detection (ScanI2CTwoWire.cpp) sends the 2-byte
command 0xD060 to 0x5D and requests 48 bytes back. GT911 ACKs the
write (treating it as a register address) and returns 48 bytes of
register data, passing the length check — a false-positive SFA30
detection.
Confirmed via second cold-boot log: after the previous commit moved GT911
to 0x14 in lateInitVariant(), address 0x5D *still* appeared in the scan
because the scanner runs first. The board has no physical SFA30 fitted.
Fix
---
Add the GT911 address-latch reset sequence to earlyInitVariant(), before
Wire is initialised and before the I2C scan runs. Per the datasheet:
drive RST LOW, drive INT HIGH (selects address 0x14 / SLAVE_ADDRESS_H),
hold >100 µs, release RST, wait >5 ms startup. GPIO-only, no Wire
dependency. lateInitVariant() then repeats this sequence internally via
touch.begin(); the double-reset is harmless.
Verified in boot log:
Before: "SFA30 found at address 0x5d", 5 I2C devices, NACK errors
After: no SFA30 entry, 4 I2C devices (TCA9535/PCF8563/BQ27220/BQ25896),
GT911 found at 0x14 and touch initialised successfully,
AirQualityTelemetry registers no sensors (correct — no SFA30 present)
* t5s3_epaper: add variant_shutdown() for touch sleep and backlight off
Put GT911 into low-power standby (command 0x05) and drive BOARD_BL_EN
LOW before deep sleep to avoid unnecessary current draw.
* t5s3_epaper: fix touch gesture routing and coordinate mapping
readTouch() now transforms raw GT911 axes to visual-frame coordinates
based on the current display rotation (rotation=3 is the hardware
identity). This ensures TouchScreenBase detects swipe direction
correctly regardless of which rotation the user has selected.
TouchInkHUDBridge dynamically sets joystick.alignment = (4-rotation)%4
on each touch event so that (rotation+alignment)%4==0 always, keeping
nav calls pass-through without remapping.
nicheGraphics.h now calls loadSettings() first so that rotation is
persisted across reboots. rotation=3 and other first-boot defaults are
only applied when tips.firstBoot is set. alignment is recomputed from
the loaded rotation on every boot.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* t5s3_epaper: fix GT911 sleep timing via notifyDeepSleep observer
touch.sleep() was called from variant_shutdown(), which runs inside
cpuDeepSleep() — after Wire.end() had already torn down the I2C bus in
doDeepSleep(). This caused Wire NULL TX buffer errors and left the GT911
awake during deep sleep.
Register a CallbackObserver on notifyDeepSleep, which fires before
Wire.end(), so the I2C command reaches the chip while the bus is live.
Pattern matches LatchingBacklight and other NicheGraphics components.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* t5s3_epaper: fix touch nav and applet defaults in nicheGraphics
Enable joystick mode post-begin so menu scroll and swipe-up/down
gestures are not silently dropped by the joystick.enabled gate in
Events.cpp. Activate DMs and Channel 0/1 applets with correct
autoshow defaults matching the mini-epaper-s3 reference pattern.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* Update nicheGraphics.h
* t5s3_epaper: fix ED047TC1 driver docs and remove spurious beginPolling
Addressing PR review comments:
Remove beginPolling(1, 0) after the blocking FastEPD update — it
incorrectly set updateRunning=true for one loop cycle after the
hardware was already done, causing busy() to briefly return true.
Since isUpdateDone() always returns true, no polling is needed.
Also fix stale comments: safe-area buffer size was 944×532, now
944×523; V_OFFSET_ROWS didn't exist, replaced with the actual
V_OFFSET_TOP=9 / V_OFFSET_BOTTOM=8 constant names.
* t5s3_epaper: clean up applet addition formatting in setupNicheGraphics
* t5s3_epaper: guard ED047TC1.cpp against non-T5S3 InkHUD builds
The InkHUD base config pulls in all of src/graphics/niche/ so every
InkHUD device compiled ED047TC1.cpp, triggering the #error on line 48
for boards that define neither T5_S3_EPAPER_PRO_V1 nor V2.
Wrap the file body with #ifdef T5_S3_EPAPER_PRO so it is only compiled
for T5S3 targets. The #error is preserved inside the guard to catch
future hardware revisions that forget to update the driver.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Nodelist cleanup
* Trunk fix
* getTextWidth cleanup
Updated the lambda to cache width in textW and reuse it instead of repeatedly calling getTextWidth(text) for unchanged text.
* Putting back hopAway ==0 condition as mentioned relayed signal is missleading
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* onNavUp() sets the menu cursor to the last item if not shown
* skip headers when showing the menu cursor in onNavUp() and onNavDown()
* skip headers when showing the menu cursor in onButtonShortPress()
* brace cursor incrementing
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Allow inkhud user applets to consume inputs with opt-in system
Adds a way for applets to subscribe to input events while keeping it off
by default to preserve compatibility and expected behaviours. Adds
example for use as well.
* Add check for nullptr on getActiveApplet uses
* Remove redundant includes
* Move subscribedInputs to protected
* More consistent naming scheme
* simplify the observer pattern, since all the called functions are const getters.
* use arduino macro over std: for numerical values and refactor local variables in drawScrollbar()
* oh, so Cppcheck actually complained about const pointers not being const.
* slowly getting out of ifdef hell
* fix inkHUD warnings as well
* last 2 check warnings
* git checks should fail on low defects from now on
* Inkhud battery icon improvements.
Fixes the battery icon draining from the flat side towards the bump, which is backwards from general design language seen on most devices
By request of kr0n05_ on discord, adds the ability to mirror the battery icon which fixes that issue in another way, and is also a common design seen on other devices.
* Remove option for icon mirroring
* Add border + dither to battery to prevent font overlap
* Fix trunk format
* Code cleanup, courtesy of Xaositek.
* Added keyboard option to menu. Shows a keyboard layout but does not type.
* Keyboard types into text box and wraps.
* send FreeText messages from the send submenu
- renamed `KEYBOARD` action to `FREE_TEXT` and moved its menu location
to the send submenu
- opening the FreeText applet from the menu keeps the menu open and
disabled the timeout
- the FreeText applet writes to inkhud->freetext
- the sending a canned message checks inkhud->freetext and if it isn't
empty, sends and clears the inkhud->freetext
* Text scrolls along with input
* handle free text message completion as an event
implements `handleFreeText` and `OnFreeText()` for system applets to
interface with the FreeText Applet
The FreeText Applet generates an `OnFreeText` event when completing a
message which is handled by the first system applet with the
`handleFreeText` flag set to true.
The Menu Applet now handles this event.
* call `onFreeText` whenever the FreeText Applet exits
allows the menu to consistently restart its auto-close timeout
* Add text cursor
* Change UI to remove the header and make text box longer
Keyboard displays captial letters for legibility
Keyboard types captial letters with long press
* center FreeText keys and draw symbolic buttons
Move input field and keyboard drawing to their own functions:
- `drawInputField()`
- `drawKeyboard()`
Store the keys in a 1-dimensional array
Implement a matching array, `keyWidths`, to set key widths relative to
the font size
* Add character limit and counter
* Fix softlock when hitting character limit
* Move text box as its own menu page
* rework FreeTextApplet into KeyboardApplet
- The Keyboard Applet renders an on-screen keyboard at the lower portion
of the screen.
- Calling `inkhud->openKeyboard()` sends all the user applets to the
background and resizes the first system applet with `handleFreeText` set
to True to fit above the on-screen keyboard
- `inkhud->closeKeyboard()` reverses this layout change
* Fix input box rendering and add character limit to menu free text
* remove FREE_TEXT menu page and use the FREE_TEXT menu action solely
* force update when changing the free text message
* reorganize KeyboardApplet
- add comments after each row of `key[]` and `keyWidths[]` to preserve
formatting
- The selected key is now set using the key index directly
- rowWidths are pre-calculated in the KeyboardApplet constructor
- removed `drawKeyboard()` and implemented `drawKeyLabel()`
* implement `Renderer::clearTile()` to clear the region below a tile
* add parameter to forceUpdate() for re-rendering the full screen
setting the `all` parameter to true in `inkhud->forceUpdate()` now
causes the full screen buffer to clear an re-render. This is helpful for
when sending applets to the background and the UI needs a clean canvas.
System Applets can now set the `alwaysRender` flag true which causes it
to re-render on every screen update. This is set to true in the Battery
Icon Applet.
* clean up tile clearing loops
* implement dirty rendering to let applets draw over their previous render
- `Applet::requestUpdate()` now has an optional flag to keep the old
canvas
- If honored, the renderer calls `render(true)` which runs
`onDirtyRender()` instead of `onRender()` for said applet
- The renderer will not call a dirty render if the full screen is
getting re-rendered
* simplify arithmetic in clearTile for better understanding
* combine Applet::onRender() and Applet::onDirtyRender() into Applet::onRender(bool full)
- add new `full` parameter to onRender() in every applet. This parameter
can be ignored by most applets.
- `Applet::requestUpdate()` has an optional flag that requests a full
render by default
* implement tile and partial rendering in KeyboardApplet
* add comment for drawKeyLabel()
* improve clarity of byte operations in clearTile()
* remove typo and commented code
* fix inaccurate comments
* add null check to openKeyboard() and closeKeyboard()
---------
Co-authored-by: zeropt <ferr0fluidmann@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Change canned message recipient's previous page to send page
* Set previousPage for new menu pages
Set nextPage in back MenuPages to previousPage
Removed back MenuAction
---------
Co-authored-by: zeropt <ferr0fluidmann@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* InkHUD: Region Picker on initial setup
* Added Node Config menu with Lora Region Picker
* Role picker
* Preset Picker
* Timezone picker added
* Power save mode and bluetooth configs
* Config section Headers
* Channel Config
* Cleaning some behavior
* Add back to all Options
* Display config added
* Position Toggle added
* Network Config for ESP32
* Wifi details
* Reduce line spacing to fit more content
* Recent list with checkboxes
* Timezone labels easier to understand
* Trunk fix
* Added "Saving Changes" screen when reboot is needed
* Trunk fix
* Make Tips show after first boot if the region is Unset
* Added ResetDB and keep only favorite commands
* quick fix to joystick
* Trunk Fix
* Fix to tips to work with new joystick input
* Added ADC multiplier value display on power config
* added ADC calibration feature
* Fixed missing stray endiff
* GPS toggle now is aware if gps is present.
* add Greek special font
* add Greek fonts with with proper Greek glyphs
* lint fix ( run trunk fmt)
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
Thomas Göttgens