22 Commits

Include renames

Author	SHA1	Message	Date
Kevin Hester	91f4e17037	fix build for my hacked up nrf52 devboard (must use SD140)	2021-10-15 10:21:42 -07:00
Kevin Hester	c940d22a98	t-echo: enable nrfupload	2021-04-28 15:25:54 +08:00
Kevin Hester	2a9b2d3b29	official name for t-echo board	2021-04-27 10:21:54 +08:00
Kevin Hester	0a6d88a2d0	add not complete WIP for wizcore4600	2021-04-16 12:23:38 +08:00
Kevin Hester	328b24537f	rak4631: builds but WIP	2021-04-11 13:33:27 +08:00
Vadim Furman	c62863b1dc	Merge from origin	2021-03-14 19:42:57 -07:00
Vadim Furman	98d878cdfe	Port to lora_isp4520 board	2021-03-14 19:00:20 -07:00
Kevin Hester	51d0d0d6c5	begin new ttgo eink board	2021-01-16 09:57:55 +08:00
Kevin Hester	047df76373	move rev 0.1 of the ttgo eink board to eink0.1	2021-01-16 09:55:06 +08:00
Kevin Hester	bbc36f7b6f	switch to my new SD 7.2.0 S113 based bootloader	2020-10-31 12:22:20 +08:00
Kevin Hester	4ad562b9f4	The new 7.2.0 soft device works on nrf52833	2020-10-28 13:01:50 +08:00
Kevin Hester	5f2f3c94b9	PPR1 and allow boards to set lower or higher sx1262 power limits	2020-10-15 13:47:10 +08:00
Kevin Hester	965c2bda8d	corvus2 board builds	2020-10-13 13:59:06 +08:00
geeksville	5fbeaee0b0	eink kinda builds	2020-09-24 14:36:43 -07:00
geeksville	22946b5e51	@BigCorvus board now kinda boots ... ###RTT Client: ----------------------------------------------- ###RTT Client: Connecting to J-Link RTT Server via localhost:19021 ... ###RTT Client: Connected. SEGGER J-Link V6.70c - Real time terminal output SEGGER J-Link ARM V9.6, SN=69663845 Process: JLinkGDBServerCLExe Emitting reboot packet for serial shell I2C device found at address 0x55 done Meshtastic swver=unset, hwver=unset Reset reason: 0x0 FIXME, call randomSeed ERROR: No UBLOX GPS found Hoping that NEMA might work RadioConfig reset! Initial packet id 1481765933, numPacketId 4294967295 No saved preferences found NODENUM=0xB18C3A4E, dbsize=1 Starting meshradio init... Set radio: name=Default, config=3, ch=6, power=17 SX1262 init result 0 sending owner !df5db18c3a4e/Unknown 3a4e/?4E Update DB node 0xB18C3A4E, rx_time=0 old user !df5db18c3a4e/Unknown 3a4e/?4E updating changed=0 user !df5db18c3a4e/Unknown 3a4e/?4E Adding packet record (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 Payload:User) enqueuing for send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted) txGood=0,rxGood=0,rxBad=0 Starting low level send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted) assert failed src/mesh/SX1262Interface.cpp: 102, virtual void SX1262Interface::setStandby(), test=err == ERR_NONE	2020-08-17 11:29:00 -07:00
geeksville	b00a936f41	WIP RAK815 support	2020-07-10 11:02:29 -07:00
geeksville	311d1a56b4	make a bare nrf52840dk build which will work for everyone	2020-07-09 20:05:39 -07:00
geeksville	ed589727d6	Update NRF52 build to work again	2020-07-09 19:57:55 -07:00
geeksville	8b911aba7f	Cleanup build for NRF52 targets	2020-05-10 12:33:17 -07:00
geeksville	814c126e67	ugly WIP on switching to RadioLib, still need to set freq etc...	2020-04-29 14:54:03 -07:00
geeksville	b8b503cb0a	Add starting point of PPR variants definition	2020-04-24 12:40:22 -07:00
geeksville	bb885a5110	add a variant based on the nrf52840-dk but with a RC clock. ... Because I was dumb and accidentally ran some code that configured gpio 0 as an output and that was enough to smoke the xtal that was preinstalled between P0.0 and P0.1.	2020-04-24 12:30:06 -07:00