Upgrade trunk (#10481)

Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>

.devcontainer/devcontainer.json

@@ -8,17 +8,21 @@
   "features": {
     "ghcr.io/devcontainers/features/python:1": {
       "installTools": true,
-      "version": "3.14"
+      "version": "3.13"
     }
   },
   "customizations": {
     "vscode": {
       "extensions": [
         "ms-vscode.cpptools",
-        "platformio.platformio-ide",
+        "Jason2866.esp-decoder",
+        "pioarduino.pioarduino-ide",
         "Trunk.io"
       ],
-      "unwantedRecommendations": ["ms-azuretools.vscode-docker"],
+      "unwantedRecommendations": [
+        "ms-azuretools.vscode-docker",
+        "platformio.platformio-ide"
+      ],
       "settings": {
         "extensions.ignoreRecommendations": true
       }

.trunk/trunk.yaml

@@ -4,11 +4,11 @@ cli:
 plugins:
   sources:
     - id: trunk
-      ref: v1.9.0
+      ref: v1.10.0
       uri: https://github.com/trunk-io/plugins
 lint:
   enabled:
-    - checkov@3.2.528
+    - checkov@3.2.529
     - renovate@43.150.0
     - prettier@3.8.3
     - trufflehog@3.95.3
@@ -16,7 +16,7 @@ lint:
     - bandit@1.9.4
     - trivy@0.70.0
     - taplo@0.10.0
-    - ruff@0.15.12
+    - ruff@0.15.13
     - isort@8.0.1
     - markdownlint@0.48.0
     - oxipng@10.1.1

.vscode/extensions.json

@@ -1,10 +1,10 @@
 {
-    // See http://go.microsoft.com/fwlink/?LinkId=827846
-    // for the documentation about the extensions.json format
     "recommendations": [
-        "platformio.platformio-ide"
+        "Jason2866.esp-decoder",
+        "pioarduino.pioarduino-ide"
     ],
     "unwantedRecommendations": [
-        "ms-vscode.cpptools-extension-pack"
+        "ms-vscode.cpptools-extension-pack",
+        "platformio.platformio-ide"
     ]
 }

bin/config.d/lora-station-g3.yaml

@@ -0,0 +1,18 @@
+# Station G3 motherboard with a Raspberry Pi Zero 2W as the MCU daughterboard.
+# Verify spidev / I2C device paths for your OS — they may differ.
+Meta:
+  name: Station G3
+  support: community
+  compatible:
+    - raspberry-pi
+
+Lora:
+  Module: sx1262
+  IRQ: 22                       # BCM pin — wiki spec
+  Reset: 16                     # BCM pin — wiki spec
+  Busy: 24                      # BCM pin — wiki spec
+  # CS: 8                       # BCM 8 = SPI0 CE0 (default); uncomment only to override
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  spidev: spidev0.0
+  # SX126X_MAX_POWER: 19        # matches Station G2 firmware cap; raise carefully per PA jumper mode

boards/station-g3.json

@@ -0,0 +1,41 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "esp32s3_out.ld",
+      "memory_type": "qio_opi"
+    },
+    "core": "esp32",
+    "extra_flags": [
+      "-DBOARD_HAS_PSRAM",
+      "-DARDUINO_USB_CDC_ON_BOOT=1",
+      "-DARDUINO_USB_MODE=1",
+      "-DARDUINO_RUNNING_CORE=1",
+      "-DARDUINO_EVENT_RUNNING_CORE=0"
+    ],
+    "f_cpu": "240000000L",
+    "f_flash": "80000000L",
+    "flash_mode": "qio",
+    "hwids": [["0x303A", "0x1001"]],
+    "mcu": "esp32s3",
+    "variant": "station-g3"
+  },
+  "connectivity": ["wifi", "bluetooth", "lora"],
+  "debug": {
+    "default_tool": "esp-builtin",
+    "onboard_tools": ["esp-builtin"],
+    "openocd_target": "esp32s3.cfg"
+  },
+  "frameworks": ["arduino", "espidf"],
+  "name": "BQ Station G3",
+  "upload": {
+    "flash_size": "16MB",
+    "maximum_ram_size": 327680,
+    "maximum_size": 16777216,
+    "use_1200bps_touch": true,
+    "wait_for_upload_port": true,
+    "require_upload_port": true,
+    "speed": 921600
+  },
+  "url": "",
+  "vendor": "BQ Consulting"
+}

src/graphics/SharedUIDisplay.cpp

@@ -27,6 +27,12 @@ ScreenResolution determineScreenResolution(int16_t screenheight, int16_t screenw
         return ScreenResolution::UltraLow;
     }
 
+#ifdef DISPLAY_FORCE_SMALL_FONTS
+    if (screenwidth <= 160 && screenheight <= 80) {
+        return ScreenResolution::Low;
+    }
+#endif
+
     // Standard OLED screens
     if (screenwidth > 128 && screenheight <= 64) {
         return ScreenResolution::Low;

src/mesh/wifi/WiFiAPClient.cpp

@@ -291,10 +291,8 @@ static int32_t reconnectWiFi()
 #endif
         return 1000; // check once per second
     } else {
-#ifdef ARCH_RP2040
+        onNetworkConnected(); // will only do anything once (guarded by APStartupComplete)
-        onNetworkConnected(); // will only do anything once
+        return 300000;        // every 5 minutes
-#endif
-        return 300000; // every 5 minutes
     }
 }
 
@@ -343,9 +341,6 @@ bool initWifi()
         const char *wifiPsw = config.network.wifi_psk;
 
 #ifndef ARCH_RP2040
-#if !MESHTASTIC_EXCLUDE_WEBSERVER
-        createSSLCert(); // For WebServer
-#endif
         WiFi.persistent(false); // Disable flash storage for WiFi credentials
 #endif
         if (!*wifiPsw) // Treat empty password as no password
@@ -370,6 +365,9 @@ bool initWifi()
 #endif
             }
 #ifdef ARCH_ESP32
+            // Register WiFi event handler BEFORE createSSLCert() to prevent race condition:
+            // Without this, WiFi can auto-reconnect during cert generation and fire GOT_IP
+            // before the handler is registered, causing onNetworkConnected() to never run.
             WiFi.onEvent(WiFiEvent);
             WiFi.setAutoReconnect(true);
             WiFi.setSleep(false);
@@ -391,6 +389,12 @@ bool initWifi()
                     wifiDisconnectReason = info.wifi_sta_disconnected.reason;
                 },
                 WiFiEvent_t::ARDUINO_EVENT_WIFI_STA_DISCONNECTED);
+#endif
+
+#ifndef ARCH_RP2040
+#if !MESHTASTIC_EXCLUDE_WEBSERVER
+            createSSLCert(); // For WebServer - called after WiFi.onEvent() to avoid race condition
+#endif
 #endif
             LOG_DEBUG("JOINING WIFI soon: ssid=%s", wifiName);
             wifiReconnect = new Periodic("WifiConnect", reconnectWiFi);

src/platform/esp32/architecture.h

@@ -158,6 +158,8 @@
 #define HW_VENDOR meshtastic_HardwareModel_CHATTER_2
 #elif defined(STATION_G2)
 #define HW_VENDOR meshtastic_HardwareModel_STATION_G2
+#elif defined(STATION_G3)
+#define HW_VENDOR meshtastic_HardwareModel_STATION_G3
 #elif defined(UNPHONE)
 #define HW_VENDOR meshtastic_HardwareModel_UNPHONE
 #elif defined(WIPHONE)

variants/esp32s3/station-common/station_common.h

@@ -0,0 +1,38 @@
+// Shared pin/feature defines for BQ Station G2 and G3.
+// Boards differ only in PA output power (SX126X_MAX_POWER) and the wiki URL.
+#pragma once
+
+// Station G2/G3 may not have GPS installed, but have a GROVE GPS Socket for an optional GPS module
+#define GPS_RX_PIN 7
+#define GPS_TX_PIN 15
+
+// 1.3 inch OLED Screen
+#define USE_SH1107_128_64
+
+#define I2C_SDA 5
+#define I2C_SCL 6
+
+#define BUTTON_PIN 38 // Program button
+#define BUTTON_NEED_PULLUP
+
+#define USE_SX1262
+
+#define LORA_MISO 14
+#define LORA_SCK 12
+#define LORA_MOSI 13
+#define LORA_CS 11
+
+#define LORA_RESET 21
+#define LORA_DIO1 48
+
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS // Compatibility alias; prefer LORA_CS in board definitions.
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY 47
+#define SX126X_RESET LORA_RESET
+
+// DIO2 controls an antenna switch and the TCXO voltage is controlled by DIO3
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+// NOTE: SX126X_MAX_POWER is intentionally NOT defined here — each board sets it.
+#endif

variants/esp32s3/station-g2/platformio.ini

@@ -26,6 +26,7 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D STATION_G2
   -I variants/esp32s3/station-g2
+  -I variants/esp32s3/station-common
   -DBOARD_HAS_PSRAM
   -DSTATION_G2
   -DARDUINO_USB_MODE=1

variants/esp32s3/station-g2/variant.h

@@ -2,39 +2,9 @@
 Board Information: https://wiki.uniteng.com/en/meshtastic/station-g2
 */
 
-// Station G2 may not have GPS installed, but it has a GROVE GPS Socket for Optional GPS Module
+#include "station_common.h"
-#define GPS_RX_PIN 7
-#define GPS_TX_PIN 15
-
-// Station G2 has 1.3 inch OLED Screen
-#define USE_SH1107_128_64
-
-#define I2C_SDA 5 // I2C pins for this board
-#define I2C_SCL 6
-
-#define BUTTON_PIN 38 // This is the Program Button
-#define BUTTON_NEED_PULLUP
-
-#define USE_SX1262
-
-#define LORA_MISO 14
-#define LORA_SCK 12
-#define LORA_MOSI 13
-#define LORA_CS 11
-
-#define LORA_RESET 21
-#define LORA_DIO1 48
 
 #ifdef USE_SX1262
-#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
-#define SX126X_DIO1 LORA_DIO1
-#define SX126X_BUSY 47
-#define SX126X_RESET LORA_RESET
-
-//  DIO2 controlls an antenna switch and the TCXO voltage is controlled by DIO3
-#define SX126X_DIO2_AS_RF_SWITCH
-#define SX126X_DIO3_TCXO_VOLTAGE 1.8
-
 // Ensure the PA does not exceed the saturation output power. More
 // Info:https://wiki.uniteng.com/en/meshtastic/station-g2#summary-for-lora-power-amplifier-conduction-test
 #define SX126X_MAX_POWER 19

variants/esp32s3/station-g3/pins_arduino.h

@@ -0,0 +1,21 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// GPIO48 Reference: https://github.com/espressif/arduino-esp32/pull/8600
+
+// The default Wire will be mapped to Screen and Sensors
+static const uint8_t SDA = 5;
+static const uint8_t SCL = 6;
+
+// Default SPI will be mapped to Radio
+static const uint8_t MISO = 14;
+static const uint8_t SCK = 12;
+static const uint8_t MOSI = 13;
+static const uint8_t SS = 11;
+
+#endif /* Pins_Arduino_h */

variants/esp32s3/station-g3/platformio.ini

@@ -0,0 +1,32 @@
+[env:station-g3]
+custom_meshtastic_hw_model = 134
+custom_meshtastic_hw_model_slug = STATION_G3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = Station G3
+custom_meshtastic_images = station-g3.svg
+custom_meshtastic_tags = B&Q
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
+extends = esp32s3_base
+board = station-g3
+board_level = pr
+board_check = true
+board_build.partitions = default_16MB.csv
+board_build.mcu = esp32s3
+upload_protocol = esptool
+;upload_port = /dev/ttyACM0
+upload_speed = 921600
+build_unflags =
+  ${esp32s3_base.build_unflags}
+  -DARDUINO_USB_MODE=0
+build_flags =
+  ${esp32s3_base.build_flags}
+  -D STATION_G3
+  -I variants/esp32s3/station-g3
+  -I variants/esp32s3/station-common
+  -DBOARD_HAS_PSRAM
+  -DSTATION_G3
+  -DARDUINO_USB_MODE=1

variants/esp32s3/station-g3/variant.h

@@ -0,0 +1,22 @@
+#include "station_common.h"
+
+#ifdef USE_SX1262
+// Station G3 reuses the same Fast-Transient DC-DC PA design as G2 (BQ35LORA900V1M).
+// PA Operating Mode is set in hardware via the PA-PL1 / PA-PL2 jumpers.
+// 19 matches the G2 cap (SX1262 19 dBm in → ~31 dBm PA out at Power Level 1, ISM compliant).
+// Raise (max 22) only if running a higher PA Power Level and you can stay within local band limits.
+#define SX126X_MAX_POWER 19
+#endif
+
+/*
+#define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
+#define ADC_MULTIPLIER 4
+#define BATTERY_SENSE_SAMPLES 15 // Set the number of samples, It has an effect of increasing sensitivity.
+#define BAT_FULLVOLT 8400
+#define BAT_EMPTYVOLT 5000
+#define BAT_CHARGINGVOLT 8400
+#define BAT_NOBATVOLT 4460
+#define CELL_TYPE_LION // same curve for liion/lipo
+#define NUM_CELLS 2
+*/

variants/native/portduino.ini

@@ -29,7 +29,7 @@ lib_deps =
   # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
   lovyan03/LovyanGFX@1.2.21
   ; # renovate: datasource=git-refs depName=libch341-spi-userspace packageName=https://github.com/pine64/libch341-spi-userspace gitBranch=main
-  https://github.com/pine64/libch341-spi-userspace/archive/23c42319a69cffcb65868e3c72e6bed83974a393.zip
+  https://github.com/pine64/libch341-spi-userspace/archive/2e5ff751d0c39667993df672cb683740ed5c9394.zip
   # renovate: datasource=custom.pio depName=adafruit/Adafruit seesaw Library packageName=adafruit/library/Adafruit seesaw Library
 	adafruit/Adafruit seesaw Library@1.7.9
   # renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main