Park unused LNA_CTRL_MCU net with pulldown on makerfabs_pucky

Added TX Power curve.

.github/copilot-instructions.md

@@ -4,11 +4,11 @@ This document provides context and guidelines for AI assistants working with the
 
 ## Project Overview
 
-Meshtastic is an open-source LoRa mesh networking project for long-range, low-power communication without relying on internet or cellular infrastructure. The firmware enables text messaging, location sharing, and telemetry over a decentralized mesh network.
+Meshtastic is an open-source LoRa mesh networking project for long-range, low-power communication without relying on internet or cellular infrastructure. The firmware enables text messaging, location sharing, and telemetry over a decentralized mesh network. The project uses **C++17** as its language standard across all platforms.
 
 ### Supported Hardware Platforms
 
-- **ESP32** (ESP32, ESP32-S3, ESP32-C3) - Most common platform
+- **ESP32** (ESP32, ESP32-S3, ESP32-C3, ESP32-C6) - Most common platform
 - **nRF52** (nRF52840, nRF52833) - Low power Nordic chips
 - **RP2040/RP2350** - Raspberry Pi Pico variants
 - **STM32WL** - STM32 with integrated LoRa
@@ -80,21 +80,46 @@ firmware/
 │   │   ├── NodeDB.*       # Node database management
 │   │   ├── Router.*       # Packet routing
 │   │   ├── Channels.*     # Channel management
+│   │   ├── CryptoEngine.* # AES-CCM encryption
 │   │   ├── *Interface.*   # Radio interface implementations
+│   │   ├── api/           # WiFi/Ethernet server APIs (ServerAPI, PacketAPI)
+│   │   ├── http/          # HTTP server (WebServer, ContentHandler)
+│   │   ├── wifi/          # WiFi support (WiFiAPClient)
+│   │   ├── eth/           # Ethernet support (ethClient)
+│   │   ├── udp/           # UDP multicast
+│   │   ├── compression/   # Message compression (unishox2)
 │   │   └── generated/     # Protobuf generated code
 │   ├── modules/           # Feature modules (Position, Telemetry, etc.)
+│   │   └── Telemetry/     # Telemetry subsystem
+│   │       └── Sensor/    # 50+ I2C sensor drivers
 │   ├── gps/               # GPS handling
 │   ├── graphics/          # Display drivers and UI
-│   ├── platform/          # Platform-specific code
+│   │   └── niche/         # Specialized UIs (InkHUD e-ink framework)
-│   ├── input/             # Input device handling
+│   ├── platform/          # Platform-specific code (esp32, nrf52, rp2xx0, stm32wl, portduino)
-│   └── concurrency/       # Threading utilities
+│   ├── input/             # Input device handling (InputBroker, keyboards, buttons)
+│   ├── detect/            # I2C hardware auto-detection (80+ device types)
+│   ├── motion/            # Accelerometer drivers (BMA423, BMI270, MPU6050, etc.)
+│   ├── mqtt/              # MQTT bridge client
+│   ├── power/             # Power HAL
+│   ├── nimble/            # BLE via NimBLE
+│   ├── buzz/              # Audio/notification (buzzer, RTTTL)
+│   ├── serialization/     # JSON serialization, COBS encoding
+│   ├── watchdog/          # Hardware watchdog thread
+│   ├── concurrency/       # Threading utilities (OSThread, Lock)
+│   ├── PowerFSM.*         # Power finite state machine
+│   └── Observer.h         # Observer/Observable event pattern
 ├── variants/              # Hardware variant definitions
 │   ├── esp32/            # ESP32 variants
 │   ├── esp32s3/          # ESP32-S3 variants
-│   ├── nrf52/            # nRF52 variants
+│   ├── esp32c3/          # ESP32-C3 variants
-│   └── rp2xxx/           # RP2040/RP2350 variants
+│   ├── esp32c6/          # ESP32-C6 variants
+│   ├── nrf52840/         # nRF52 variants
+│   ├── rp2040/           # RP2040/RP2350 variants
+│   ├── stm32/            # STM32WL variants
+│   └── native/           # Linux/Portduino variants
 ├── protobufs/            # Protocol buffer definitions
 ├── boards/               # Custom PlatformIO board definitions
+├── test/                 # Unit tests (12 test suites)
 └── bin/                  # Build and utility scripts
 ```
 
@@ -105,6 +130,7 @@ firmware/
 - Follow existing code style - run `trunk fmt` before commits
 - Prefer `LOG_DEBUG`, `LOG_INFO`, `LOG_WARN`, `LOG_ERROR` for logging
 - Use `assert()` for invariants that should never fail
+- C++17 features are available (`std::optional`, structured bindings, `if constexpr`, etc.)
 
 ### Naming Conventions
 
@@ -118,70 +144,151 @@ firmware/
 
 #### Module System
 
-Modules inherit from `MeshModule` or `ProtobufModule<T>` and implement:
+Modules use a three-tier class hierarchy:
 
-- `handleReceivedProtobuf()` - Process incoming packets
+1. **`MeshModule`** - Base class. Implement `wantPacket()` and `handleReceived()`. Returns `ProcessMessage::STOP` or `ProcessMessage::CONTINUE`.
-- `allocReply()` - Generate response packets
+2. **`SinglePortModule`** - Handles a single portnum. Simplified `wantPacket()` that checks `decoded.portnum`.
-- `runOnce()` - Periodic task execution (returns next run interval in ms)
+3. **`ProtobufModule<T>`** - Template for protobuf-based modules. Handles encoding/decoding automatically.
+
+Most modules also inherit from **`OSThread`** for periodic tasks (the "mixin" pattern):
 
 ```cpp
-class MyModule : public ProtobufModule<meshtastic_MyMessage>
+class MyModule : public ProtobufModule<meshtastic_MyMessage>, private concurrency::OSThread
 {
+  public:
+    MyModule();
+
   protected:
     virtual bool handleReceivedProtobuf(const meshtastic_MeshPacket &mp, meshtastic_MyMessage *msg) override;
-    virtual int32_t runOnce() override;
+    virtual meshtastic_MeshPacket *allocReply() override;       // Generate response packets
+    virtual int32_t runOnce() override;                         // Periodic task (returns next interval in ms)
+    virtual bool alterReceivedProtobuf(meshtastic_MeshPacket &mp, meshtastic_MyMessage *msg); // Modify in-flight
+    virtual bool wantUIFrame();                                 // Request a UI display frame
 };
 ```
 
+Modules are registered in `src/modules/Modules.cpp` guarded by `MESHTASTIC_EXCLUDE_*` flags.
+
+#### Observer/Observable Pattern
+
+Event-driven communication between subsystems uses `src/Observer.h`:
+
+```cpp
+// Observable emits events
+Observable<const meshtastic::Status *> newStatus;
+newStatus.notifyObservers(&status);
+
+// Observer receives events via callback
+CallbackObserver<MyClass, const meshtastic::Status *> statusObserver =
+    CallbackObserver<MyClass, const meshtastic::Status *>(this, &MyClass::handleStatusUpdate);
+```
+
 #### Configuration Access
 
 - `config.*` - Device configuration (LoRa, position, power, etc.)
 - `moduleConfig.*` - Module-specific configuration
 - `channels.*` - Channel configuration and management
+- `owner` - Device owner info
+- `myNodeInfo` - Local node info
 
 #### Default Values
 
 Use the `Default` class helpers in `src/mesh/Default.h`:
 
 - `Default::getConfiguredOrDefaultMs(configured, default)` - Returns ms, using default if configured is 0
+- `Default::getConfiguredOrDefault(configured, default)` - Generic configured/default getter
 - `Default::getConfiguredOrMinimumValue(configured, min)` - Enforces minimum values
 - `Default::getConfiguredOrDefaultMsScaled(configured, default, numNodes)` - Scales based on network size
 
 #### Thread Safety
 
-- Use `concurrency::Lock` for mutex protection
+- Use `concurrency::Lock` and `concurrency::LockGuard` for mutex protection
 - Radio SPI access uses `SPILock`
 - Prefer `OSThread` for background tasks
 
+### Hardware Detection
+
+`src/detect/ScanI2C` automatically enumerates 80+ I2C device types at boot including displays, sensors, RTCs, keyboards, PMUs, and touch controllers. This drives automatic initialization of the correct drivers.
+
+### Graphics/UI System
+
+Multiple display driver families in `src/graphics/`:
+
+- **OLED**: SSD1306, SH1106, ST7567
+- **TFT**: TFTDisplay (LovyanGFX-based)
+- **E-Ink**: EInkDisplay2, EInkDynamicDisplay, EInkParallelDisplay
+
+**InkHUD** (`src/graphics/niche/InkHUD/`) is an event-driven e-ink UI framework:
+
+- Applet-based architecture — modular display tiles
+- Read-only, static display optimized for minimal refreshes and low power
+- Configured per-variant via `nicheGraphics.h`
+- Separate PlatformIO config: `src/graphics/niche/InkHUD/PlatformioConfig.ini`
+
+### Input System
+
+`src/input/InputBroker` is the centralized input event dispatcher. Supports multiple input sources: buttons, keyboards (BBQ10, Cardputer, TCA8418), touch screens, rotary encoders, and matrix keyboards.
+
+### Power Management
+
+`src/PowerFSM.*` implements a finite state machine with states: `stateON`, `statePOWER`, `stateSERIAL`, `stateDARK`. Key events: `EVENT_PRESS`, `EVENT_WAKE_TIMER`, `EVENT_LOW_BATTERY`, `EVENT_RECEIVED_MSG`, `EVENT_SHUTDOWN`. Conditionally excluded with `MESHTASTIC_EXCLUDE_POWER_FSM` (falls back to `FakeFsm`).
+
+### Motion Sensors
+
+`src/motion/AccelerometerThread` provides background motion monitoring with automatic screen wake and double-tap button press detection. Supports 10+ accelerometer/gyroscope chips (BMA423, BMI270, MPU6050, LIS3DH, LSM6DS3, STK8XXX, QMA6100P, ICM20948, BMX160).
+
+### Telemetry Sensor Library
+
+`src/modules/Telemetry/Sensor/` contains 50+ I2C sensor drivers organized by category:
+
+- **Power monitoring**: INA219/226/260/3221, MAX17048
+- **Environmental**: BME280/680, SCD4X (CO₂), SEN5X (particulate)
+- **Humidity/Temperature**: SHT3X/4X, AHT10, MCP9808, MLX90614
+- **Light**: BH1750, TSL2561/2591, VEML7700, LTR390UV, OPT3001
+- **Air quality**: PMSA003I, SFA30
+- **Specialized**: CGRadSens (radiation), NAU7802 (weight scale)
+
+### API/Networking
+
+`src/mesh/api/` provides a template-based `ServerAPI` for client communication over WiFi (`WiFiServerAPI`) and Ethernet (`ethServerAPI`). Default port: **4403**. HTTP server in `src/mesh/http/`. JSON serialization in `src/serialization/MeshPacketSerializer`.
+
 ### Hardware Variants
 
 Each hardware variant has:
 
 - `variant.h` - Pin definitions and hardware capabilities
 - `platformio.ini` - Build configuration
-- Optional: `pins_arduino.h`, `rfswitch.h`
+- Optional: `pins_arduino.h`, `rfswitch.h`, `nicheGraphics.h` (for InkHUD variants)
 
 Key defines in variant.h:
 
 ```cpp
 #define USE_SX1262          // Radio chip selection
 #define HAS_GPS 1           // Hardware capabilities
+#define HAS_SCREEN 1        // Display present
 #define LORA_CS 36          // Pin assignments
 #define SX126X_DIO1 14      // Radio-specific pins
 ```
 
 ### Protobuf Messages
 
-- Defined in `protobufs/meshtastic/*.proto`
+- Defined in `protobufs/meshtastic/*.proto` (~32 proto files)
-- Generated code in `src/mesh/generated/`
+- Generated code in `src/mesh/generated/meshtastic/`
 - Regenerate with `bin/regen-protos.sh`
 - Message types prefixed with `meshtastic_`
+- Nanopb `.options` files control field sizes and encoding
 
 ### Conditional Compilation
 
 ```cpp
 #if !MESHTASTIC_EXCLUDE_GPS        // Feature exclusion
+#if !MESHTASTIC_EXCLUDE_WIFI       // Network feature exclusion
+#if !MESHTASTIC_EXCLUDE_BLUETOOTH  // BLE exclusion
+#if !MESHTASTIC_EXCLUDE_POWER_FSM  // Power FSM exclusion
 #ifdef ARCH_ESP32                   // Architecture-specific
+#ifdef ARCH_NRF52                   // Nordic platform
+#ifdef ARCH_RP2040                  // Raspberry Pi Pico
+#ifdef ARCH_PORTDUINO               // Linux native
 #if defined(USE_SX1262)            // Radio-specific
 #ifdef HAS_SCREEN                   // Hardware capability
 #if USERPREFS_EVENT_MODE           // User preferences
@@ -192,7 +299,7 @@ Key defines in variant.h:
 Uses **PlatformIO** with custom scripts:
 
 - `bin/platformio-pre.py` - Pre-build script
-- `bin/platformio-custom.py` - Custom build logic
+- `bin/platformio-custom.py` - Custom build logic, manifest generation
 
 Build commands:
 
@@ -202,21 +309,38 @@ pio run -e tbeam -t upload    # Build and upload
 pio run -e native             # Build native/Linux version
 ```
 
+### Build Manifest
+
+`bin/platformio-custom.py` emits a build manifest with metadata:
+
+- `hasMui`, `hasInkHud` - UI capability flags (overridable via `custom_meshtastic_has_mui`, `custom_meshtastic_has_ink_hud`)
+- Architecture normalization (e.g., `esp32s3` → `esp32-s3` for API compatibility)
+
 ## Common Tasks
 
 ### Adding a New Module
 
 1. Create `src/modules/MyModule.cpp` and `.h`
-2. Inherit from appropriate base class
+2. Inherit from appropriate base class (`MeshModule`, `SinglePortModule`, or `ProtobufModule<T>`)
-3. Register in `src/modules/Modules.cpp`
+3. Mix in `concurrency::OSThread` if periodic work is needed
-4. Add protobuf messages if needed in `protobufs/`
+4. Register in `src/modules/Modules.cpp` guarded by `#if !MESHTASTIC_EXCLUDE_MYMODULE`
+5. Add protobuf messages if needed in `protobufs/meshtastic/`
+6. Add test suite in `test/test_mymodule/` if applicable
 
 ### Adding a New Hardware Variant
 
 1. Create directory under `variants/<arch>/<name>/`
-2. Add `variant.h` with pin definitions
+2. Add `variant.h` with pin definitions and hardware capability defines
-3. Add `platformio.ini` with build config
+3. Add `platformio.ini` with build config — use `extends` to reference common base (e.g., `esp32s3_base`)
-4. Reference common configs with `extends`
+4. Set `custom_meshtastic_support_level = 1` (PR builds) or `2` (merge builds)
+5. For e-ink displays, add `nicheGraphics.h` for InkHUD configuration
+
+### Adding a New Telemetry Sensor
+
+1. Create driver in `src/modules/Telemetry/Sensor/` following existing sensor pattern
+2. Register I2C address in `src/detect/ScanI2C` for auto-detection
+3. Integrate with the appropriate telemetry module (Environment, Health, Power, AirQuality)
+4. Add proto fields in `protobufs/meshtastic/telemetry.proto` if new data types are needed
 
 ### Modifying Configuration Defaults
 
@@ -305,9 +429,22 @@ Most workflows can be triggered manually via `workflow_dispatch` for testing.
 
 ## Testing
 
-- Unit tests in `test/` directory
+Unit tests in `test/` directory with 12 test suites:
-- Run with `pio test -e native`
+
-- Use `bin/test-simulator.sh` for simulation testing
+- `test_crypto/` - Cryptography
+- `test_mqtt/` - MQTT integration
+- `test_radio/` - Radio interface
+- `test_mesh_module/` - Module framework
+- `test_meshpacket_serializer/` - Packet serialization
+- `test_transmit_history/` - Retransmission tracking
+- `test_atak/` - ATAK integration
+- `test_default/` - Default configuration
+- `test_http_content_handler/` - HTTP handling
+- `test_serial/` - Serial communication
+
+Run with: `pio test -e native`
+
+Simulation testing: `bin/test-simulator.sh`
 
 ## Resources
 

.github/prompts/new-module.prompt.md

@@ -0,0 +1,138 @@
+# New Meshtastic Module
+
+Guide for developing a new Meshtastic firmware module.
+
+## Module Hierarchy
+
+Choose the appropriate base class:
+
+1. **`MeshModule`** — Raw base class. Override `wantPacket()` and `handleReceived()`. Returns `ProcessMessage::STOP` or `ProcessMessage::CONTINUE`.
+2. **`SinglePortModule`** — Handles a single `meshtastic_PortNum`. Constructor takes `(name, portNum)`. Simplified `wantPacket()` checking `decoded.portnum`. Use `allocDataPacket()` to create outgoing packets.
+3. **`ProtobufModule<T>`** — Template for protobuf-encoded modules. Constructor takes `(name, portNum, fields)`. Override `handleReceivedProtobuf()`. Use `allocDataProtobuf(payload)` to create outgoing packets.
+
+Most modules also mix in `concurrency::OSThread` for periodic background tasks.
+
+## Implementation Pattern
+
+```cpp
+// src/modules/MyModule.h
+#pragma once
+#include "ProtobufModule.h"
+#include "concurrency/OSThread.h"
+
+class MyModule : public ProtobufModule<meshtastic_MyMessage>, private concurrency::OSThread
+{
+  public:
+    MyModule();
+
+  protected:
+    // Process incoming protobuf packet. Return true to stop further processing.
+    virtual bool handleReceivedProtobuf(const meshtastic_MeshPacket &mp, meshtastic_MyMessage *msg) override;
+
+    // Generate response packet (optional)
+    virtual meshtastic_MeshPacket *allocReply() override;
+
+    // Periodic task — return next run interval in ms, or disable()
+    virtual int32_t runOnce() override;
+
+    // Modify packet in-flight before delivery (optional)
+    virtual bool alterReceivedProtobuf(meshtastic_MeshPacket &mp, meshtastic_MyMessage *msg);
+
+    // Request a UI display frame (optional)
+    virtual bool wantUIFrame();
+};
+```
+
+## Registration
+
+Register in `src/modules/Modules.cpp` inside `setupModules()`:
+
+```cpp
+#if !MESHTASTIC_EXCLUDE_MYMODULE
+    new MyModule();
+#endif
+```
+
+If other code needs to reference the module instance:
+
+```cpp
+#if !MESHTASTIC_EXCLUDE_MYMODULE
+    myModule = new MyModule();
+#endif
+```
+
+And declare the global in the header:
+
+```cpp
+extern MyModule *myModule;
+```
+
+Some modules also conditionally instantiate based on `moduleConfig`:
+
+```cpp
+#if !MESHTASTIC_EXCLUDE_MYMODULE
+    if (moduleConfig.has_my_module && moduleConfig.my_module.enabled) {
+        new MyModule();
+    }
+#endif
+```
+
+## Conditional Compilation
+
+Add a `MESHTASTIC_EXCLUDE_MYMODULE` guard. This allows the module to be excluded from constrained builds. The flag name must follow the pattern: `MESHTASTIC_EXCLUDE_` + uppercase module name.
+
+## Protobuf Messages (if needed)
+
+1. Define messages in `protobufs/meshtastic/` (e.g., `mymodule.proto`)
+2. Add a `.options` file for nanopb field size constraints
+3. Regenerate with `bin/regen-protos.sh`
+4. Generated code appears in `src/mesh/generated/meshtastic/`
+5. Assign a `meshtastic_PortNum` if the module uses a new port number
+
+## Timing and Defaults
+
+Use `Default` class helpers for configurable intervals:
+
+```cpp
+int32_t MyModule::runOnce()
+{
+    uint32_t interval = Default::getConfiguredOrDefaultMs(moduleConfig.my_module.update_interval,
+                                                          default_my_module_interval);
+    // ... do work ...
+    return interval;
+}
+```
+
+On public/default channels, enforce minimums with `Default::getConfiguredOrMinimumValue()`.
+
+## Observer Pattern
+
+Subscribe to system events:
+
+```cpp
+CallbackObserver<MyModule, const meshtastic::Status *> statusObserver =
+    CallbackObserver<MyModule, const meshtastic::Status *>(this, &MyModule::handleStatusUpdate);
+```
+
+## Testing
+
+Add test suite in `test/test_mymodule/`:
+
+```
+test/
+└── test_mymodule/
+    └── test_main.cpp
+```
+
+Run with: `pio test -e native`
+
+## Checklist
+
+- [ ] Header and implementation files in `src/modules/`
+- [ ] Inherit from appropriate base class (MeshModule / SinglePortModule / ProtobufModule)
+- [ ] Mix in OSThread if periodic work is needed
+- [ ] Register in `src/modules/Modules.cpp` with `MESHTASTIC_EXCLUDE_` guard
+- [ ] Add protobuf definitions if needed (`protobufs/meshtastic/`)
+- [ ] Use `Default::getConfiguredOrDefaultMs()` for timing
+- [ ] Respect bandwidth limits on public channels
+- [ ] Add test suite in `test/`

.github/prompts/new-sensor.prompt.md

@@ -0,0 +1,149 @@
+# New Telemetry Sensor
+
+Guide for adding a new I2C telemetry sensor driver to Meshtastic firmware.
+
+## Overview
+
+Telemetry sensors live in `src/modules/Telemetry/Sensor/`. There are 50+ existing drivers organized by measurement type. Each sensor integrates with one of the telemetry modules:
+
+- **EnvironmentTelemetryModule** — Temperature, humidity, pressure, gas, light
+- **AirQualityTelemetryModule** — Particulate matter, VOCs
+- **PowerTelemetryModule** — Voltage, current, power monitoring
+- **HealthTelemetryModule** — Heart rate, SpO2, body temperature
+
+## Sensor Driver Pattern
+
+Each sensor has a `.h` and `.cpp` file pair following this pattern:
+
+```cpp
+// src/modules/Telemetry/Sensor/MySensor.h
+#pragma once
+#include "TelemetrySensor.h"
+#include <MySensorLibrary.h>  // Arduino/PlatformIO library
+
+class MySensor : virtual public TelemetrySensor
+{
+  private:
+    MySensorLibrary sensor;
+
+  public:
+    MySensor() : TelemetrySensor(meshtastic_TelemetrySensorType_MY_SENSOR, "MySensor") {}
+
+    // Initialize sensor hardware. Return true on success.
+    virtual void setup() override;
+
+    // Read sensor data into the telemetry protobuf. Return true on success.
+    virtual bool getMetrics(meshtastic_Telemetry *measurement) override;
+};
+```
+
+```cpp
+// src/modules/Telemetry/Sensor/MySensor.cpp
+#include "MySensor.h"
+#include "TelemetrySensor.h"
+
+void MySensor::setup()
+{
+    sensor.begin();
+    // Configure sensor parameters...
+}
+
+bool MySensor::getMetrics(meshtastic_Telemetry *measurement)
+{
+    // Read from hardware
+    float value = sensor.readValue();
+
+    // Populate the appropriate protobuf variant
+    measurement->variant.environment_metrics.temperature = value;
+    // ... other fields ...
+
+    return true;
+}
+```
+
+## I2C Address Registration
+
+Register the sensor's I2C address(es) in `src/detect/ScanI2C` so it's auto-detected at boot:
+
+1. Add a `DeviceType` enum entry in `src/detect/ScanI2C.h`
+2. Add the I2C address mapping in `src/detect/ScanI2CTwoWire.cpp`
+
+The scan runs at boot and populates a device map that telemetry modules use to decide which sensors to initialize.
+
+## Protobuf Fields
+
+If the sensor provides data not covered by existing telemetry fields:
+
+1. Add fields to the appropriate message in `protobufs/meshtastic/telemetry.proto`:
+   - `EnvironmentMetrics` — Environmental measurements
+   - `AirQualityMetrics` — Air quality data
+   - `PowerMetrics` — Power/energy data
+   - `HealthMetrics` — Health/biometric data
+2. Add a `.options` constraint if needed (field sizes for nanopb)
+3. Regenerate: `bin/regen-protos.sh`
+
+## Sensor Type Enum
+
+Add the sensor to `meshtastic_TelemetrySensorType` enum in `protobufs/meshtastic/telemetry.proto`:
+
+```protobuf
+enum TelemetrySensorType {
+    // ... existing entries ...
+    MY_SENSOR = XX;
+}
+```
+
+## Integration with Telemetry Module
+
+Wire the sensor into the appropriate telemetry module. For environment sensors, this is typically in `src/modules/Telemetry/EnvironmentTelemetry.cpp`:
+
+1. Include the sensor header
+2. Add initialization in `setupSensor()` guarded by detection results
+3. Call `getMetrics()` in the measurement collection path
+
+Example pattern from existing sensors:
+
+```cpp
+#include "Sensor/MySensor.h"
+
+MySensor mySensor;
+
+// In setup:
+if (nodeTelemetrySensorsMap[meshtastic_TelemetrySensorType_MY_SENSOR].first > 0) {
+    mySensor.setup();
+}
+
+// In measurement collection:
+if (nodeTelemetrySensorsMap[meshtastic_TelemetrySensorType_MY_SENSOR].first > 0) {
+    mySensor.getMetrics(&measurement);
+}
+```
+
+## Library Dependencies
+
+If the sensor needs an external library, add it to the `lib_deps` in the relevant base platformio.ini configs:
+
+```ini
+lib_deps =
+    ${env.lib_deps}
+    mysensorlibrary@^1.0.0
+```
+
+Or use a conditional dependency if it's platform-specific.
+
+## Unit Conversions
+
+If the sensor reports values in non-standard units, use `src/modules/Telemetry/UnitConversions.h` for conversion helpers (e.g., Celsius ↔ Fahrenheit, hPa ↔ inHg).
+
+## Checklist
+
+- [ ] Create `src/modules/Telemetry/Sensor/MySensor.h` and `.cpp`
+- [ ] Inherit from `TelemetrySensor` base class
+- [ ] Implement `setup()` and `getMetrics()` methods
+- [ ] Add `meshtastic_TelemetrySensorType` enum entry in `telemetry.proto`
+- [ ] Add I2C address to `src/detect/ScanI2C` for auto-detection
+- [ ] Add protobuf fields in `telemetry.proto` if new data types needed
+- [ ] Regenerate protos: `bin/regen-protos.sh`
+- [ ] Wire into the appropriate telemetry module (Environment/AirQuality/Power/Health)
+- [ ] Add library dependency if external library required
+- [ ] Test on hardware or native build

.github/prompts/new-variant.prompt.md

@@ -0,0 +1,178 @@
+# New Hardware Variant
+
+Guide for adding a new Meshtastic hardware variant to the firmware.
+
+## Directory Structure
+
+Create under `variants/<arch>/<name>/`:
+
+```
+variants/
+├── esp32/          # ESP32
+├── esp32s3/        # ESP32-S3
+├── esp32c3/        # ESP32-C3
+├── esp32c6/        # ESP32-C6
+├── nrf52840/       # nRF52840
+├── rp2040/         # RP2040/RP2350
+├── stm32/          # STM32WL
+└── native/         # Linux/Portduino
+```
+
+Each variant needs at minimum:
+
+- `variant.h` — Pin definitions and hardware capabilities
+- `platformio.ini` — Build configuration
+
+Optional files:
+
+- `pins_arduino.h` — Arduino pin mapping overrides
+- `rfswitch.h` — RF switch control for multi-band radios
+- `nicheGraphics.h` — InkHUD e-ink configuration
+
+## variant.h Template
+
+```cpp
+// Pin definitions
+#define I2C_SDA 21
+#define I2C_SCL 22
+
+// LoRa radio
+#define USE_SX1262              // Radio chip: USE_SX1262, USE_SX1268, USE_SX1280, USE_RF95, USE_LLCC68, USE_LR1110, USE_LR1120, USE_LR1121
+#define LORA_CS   18
+#define LORA_SCK  5
+#define LORA_MOSI 27
+#define LORA_MISO 19
+#define LORA_DIO1 33            // SX126x: DIO1, SX128x: DIO1, RF95: IRQ
+#define LORA_RESET 23
+#define LORA_BUSY 32            // SX126x/SX128x only
+#define SX126X_DIO2_AS_RF_SWITCH // Common for SX1262 boards
+
+// GPS
+#define HAS_GPS 1
+#define GPS_RX_PIN 34
+#define GPS_TX_PIN 12
+// #define PIN_GPS_EN 47         // Optional GPS enable pin
+// #define GPS_BAUDRATE 9600     // Override default 9600
+
+// Display
+#define HAS_SCREEN 1
+// #define USE_SSD1306            // OLED type
+// #define USE_SH1106             // Alternative OLED
+// #define USE_ST7789             // TFT type
+// #define SCREEN_WIDTH 128
+// #define SCREEN_HEIGHT 64
+
+// LEDs
+#define LED_PIN 2               // Status LED (optional)
+// #define HAS_NEOPIXEL 1        // WS2812 support
+
+// Buttons
+#define BUTTON_PIN 38
+// #define BUTTON_PIN_ALT 0      // Secondary button
+
+// Power management
+// #define HAS_AXP192 1          // AXP192 PMU (T-Beam v1.0)
+// #define HAS_AXP2101 1         // AXP2101 PMU (T-Beam v1.2+)
+// #define BATTERY_PIN 35        // ADC battery voltage pin
+// #define ADC_MULTIPLIER 2.0    // Voltage divider ratio
+
+// Optional I2C devices
+// #define HAS_RTC 1             // Real-time clock
+// #define HAS_TELEMETRY 1       // Enable telemetry sensor support
+// #define HAS_SENSOR 1          // I2C sensors present
+```
+
+## platformio.ini Template
+
+```ini
+[env:my_variant]
+extends = esp32s3_base            ; Use architecture-specific base
+board = esp32-s3-devkitc-1        ; PlatformIO board definition (or custom in boards/)
+board_level = extra               ; Build level: extra, or omit for default
+custom_meshtastic_support_level = 1  ; 1 = PR builds, 2 = merge builds only
+
+build_flags =
+    ${esp32s3_base.build_flags}
+    -D MY_VARIANT_SPECIFIC_FLAG=1
+    -I variants/esp32s3/my_variant  ; Include path for variant.h
+
+upload_speed = 921600
+```
+
+### Common Base Configs
+
+- `esp32_base` / `esp32-common.ini` — ESP32
+- `esp32s3_base` — ESP32-S3
+- `esp32c3_base` — ESP32-C3
+- `esp32c6_base` — ESP32-C6
+- `nrf52840_base` / `nrf52.ini` — nRF52840
+- `rp2040_base` — RP2040/RP2350
+
+### Support Levels
+
+- `custom_meshtastic_support_level = 1` — Built on every PR (actively supported)
+- `custom_meshtastic_support_level = 2` — Built only on merge to main branches
+- `board_level = extra` — Only built on full releases
+
+## Build Manifest Metadata
+
+`bin/platformio-custom.py` emits UI capability flags in the build manifest:
+
+- `custom_meshtastic_has_mui = true/false` — Override MUI detection
+- `custom_meshtastic_has_ink_hud = true/false` — Override InkHUD detection
+- Architecture names are normalized (e.g., `esp32s3` → `esp32-s3`)
+
+## InkHUD E-Ink Variants
+
+For e-ink display variants using the InkHUD framework, add `nicheGraphics.h`:
+
+```cpp
+// nicheGraphics.h — InkHUD configuration for this variant
+#define INKHUD                     // Enable InkHUD
+// Configure display, applets, and refresh behavior per device
+```
+
+InkHUD has its own PlatformIO config: `src/graphics/niche/InkHUD/PlatformioConfig.ini`
+
+## I2C Device Detection
+
+If the variant has I2C devices, ensure `src/detect/ScanI2C` will detect them. The auto-detection system handles 80+ device types including displays, sensors, RTCs, keyboards, PMUs, and touch controllers at boot.
+
+## Custom Board Definitions
+
+If the PlatformIO board doesn't exist, create a custom board JSON in `boards/`:
+
+```json
+{
+  "build": {
+    "arduino": { "ldscript": "esp32s3_out.ld" },
+    "core": "esp32",
+    "f_cpu": "240000000L",
+    "f_flash": "80000000L",
+    "flash_mode": "qio",
+    "mcu": "esp32s3",
+    "variant": "esp32s3"
+  },
+  "connectivity": ["wifi", "bluetooth"],
+  "frameworks": ["arduino", "espidf"],
+  "name": "My Custom Board",
+  "upload": {
+    "flash_size": "8MB",
+    "maximum_ram_size": 327680,
+    "maximum_size": 8388608
+  },
+  "url": "https://example.com",
+  "vendor": "MyVendor"
+}
+```
+
+## Checklist
+
+- [ ] Create `variants/<arch>/<name>/variant.h` with pin definitions
+- [ ] Create `variants/<arch>/<name>/platformio.ini` extending correct base
+- [ ] Set `custom_meshtastic_support_level` (1 or 2)
+- [ ] Verify radio chip define matches hardware (`USE_SX1262`, etc.)
+- [ ] Set hardware capability flags (`HAS_GPS`, `HAS_SCREEN`, etc.)
+- [ ] Add custom board JSON in `boards/` if needed
+- [ ] Test build: `pio run -e my_variant`
+- [ ] For e-ink: add `nicheGraphics.h` with InkHUD config

.github/workflows/docker_build.yml

@@ -56,6 +56,25 @@ jobs:
           echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
         id: version
 
+      - name: Set up QEMU
+        uses: docker/setup-qemu-action@v4
+        with:
+          cache-image: true
+
+      - name: Docker setup
+        uses: docker/setup-buildx-action@v4
+        with:
+          # Add Google/Amazon DockerHub mirrors to buildkit config
+          # https://docs.docker.com/build/ci/github-actions/configure-builder/#registry-mirror
+          buildkitd-config-inline: |
+            [registry."docker.io"]
+              mirrors = ["mirror.gcr.io", "public.ecr.aws"]
+
+      - name: Sanitize platform string
+        id: sanitize_platform
+        # Replace slashes with underscores
+        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
+
       - name: Docker login
         if: ${{ inputs.push }}
         uses: docker/login-action@v4
@@ -63,17 +82,6 @@ jobs:
           username: meshtastic
           password: ${{ secrets.DOCKER_FIRMWARE_TOKEN }}
 
-      - name: Set up QEMU
-        uses: docker/setup-qemu-action@v4
-
-      - name: Docker setup
-        uses: docker/setup-buildx-action@v4
-
-      - name: Sanitize platform string
-        id: sanitize_platform
-        # Replace slashes with underscores
-        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
-
       - name: Docker tag
         id: meta
         uses: docker/metadata-action@v6
@@ -95,3 +103,6 @@ jobs:
           platforms: ${{ inputs.platform }}
           build-args: |
             PIO_ENV=${{ inputs.pio_env }}
+          # Cache image layers in GitHub Actions cache to speed up subsequent builds.
+          cache-from: type=gha
+          cache-to: type=gha,mode=max

.github/workflows/main_matrix.yml

@@ -301,15 +301,17 @@ jobs:
         id: release_notes
         run: |
           chmod +x ./bin/generate_release_notes.py
-          NOTES=$(./bin/generate_release_notes.py ${{ needs.version.outputs.long }})
+          NOTES=$(./bin/generate_release_notes.py ${{ needs.version.outputs.long }} --compare-ref HEAD 2>release_notes.log)
           echo "notes<<EOF" >> $GITHUB_OUTPUT
           echo "$NOTES" >> $GITHUB_OUTPUT
           echo "EOF" >> $GITHUB_OUTPUT
+          echo "### Release note range" >> $GITHUB_STEP_SUMMARY
+          cat release_notes.log >> $GITHUB_STEP_SUMMARY
         env:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
       - name: Create release
-        uses: softprops/action-gh-release@v2
+        uses: softprops/action-gh-release@v3
         id: create_release
         with:
           draft: true
@@ -466,7 +468,7 @@ jobs:
       - name: Generate release notes
         run: |
           chmod +x ./bin/generate_release_notes.py
-          ./bin/generate_release_notes.py ${{ needs.version.outputs.long }} > ./publish/release_notes.md
+          ./bin/generate_release_notes.py ${{ needs.version.outputs.long }} --compare-ref HEAD > ./publish/release_notes.md
         env:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 

.github/workflows/models_issue_triage.yml

@@ -38,7 +38,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
         with:
@@ -80,7 +80,7 @@ jobs:
       # ─────────────────────────────────────────────────────────────────────────
       - name: Determine if completeness check should be skipped
         if: steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == ''
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         id: check-skip
         with:
           script: |
@@ -134,7 +134,7 @@ jobs:
 
       - name: Process analysis result
         if: (steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == '') && steps.check-skip.outputs.should_skip != 'true' && steps.analysis.outputs.response != ''
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         id: process
         env:
           AI_RESPONSE: ${{ steps.analysis.outputs.response }}
@@ -174,7 +174,7 @@ jobs:
 
       - name: Apply triage label
         if: steps.process.outputs.label != '' && steps.process.outputs.label != 'none'
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         env:
           LABEL_NAME: ${{ steps.process.outputs.label }}
         with:
@@ -200,7 +200,7 @@ jobs:
 
       - name: Comment on issue
         if: steps.process.outputs.should_comment == 'true'
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         env:
           COMMENT_BODY: ${{ steps.process.outputs.comment_body }}
         with:

.github/workflows/models_pr_triage.yml

@@ -22,7 +22,7 @@ jobs:
       # Step 1: Check if PR already has automation/type labels (skip if so)
       # ─────────────────────────────────────────────────────────────────────────
       - name: Check existing labels
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         id: check-labels
         with:
           script: |
@@ -58,7 +58,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.check-labels.outputs.skip_all != 'true' && steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         id: quality-label
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
@@ -113,7 +113,7 @@ jobs:
 
       - name: Apply type label
         if: steps.check-labels.outputs.skip_all != 'true' && steps.check-labels.outputs.has_type_label != 'true' && steps.classify.outputs.response != ''
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         env:
           TYPE_LABEL: ${{ steps.classify.outputs.response }}
         with:

.github/workflows/package_ppa.yml

@@ -5,6 +5,8 @@ on:
     secrets:
       PPA_GPG_PRIVATE_KEY:
         required: true
+      PPA_SFTP_PRIVATE_KEY:
+        required: true
     inputs:
       ppa_repo:
         description: Meshtastic PPA to target
@@ -27,6 +29,7 @@ jobs:
       build_location: ppa
 
   package-ppa:
+    if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
     runs-on: ubuntu-24.04
     needs: build-debian-src
     steps:
@@ -40,7 +43,7 @@ jobs:
         shell: bash
         run: |
           sudo apt-get update -y --fix-missing
-          sudo apt-get install -y dput
+          sudo apt-get install -y dput openssh-client
 
       - name: Import GPG key
         uses: crazy-max/ghaction-import-gpg@v7
@@ -65,8 +68,42 @@ jobs:
       - name: Display structure of downloaded files
         run: ls -lah
 
-      - name: Publish with dput
+      - name: Trust Launchpad's SSH key
-        if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
-        timeout-minutes: 15 # dput is terrible, sometimes runs 'forever'
         run: |
-          dput ${{ inputs.ppa_repo }} meshtasticd_${{ steps.version.outputs.deb }}~${{ inputs.series }}_source.changes
+          mkdir -p ~/.ssh
+          ssh-keyscan -H ppa.launchpad.net >> ~/.ssh/known_hosts
+
+      - name: Setup dput config
+        env:
+          ppa_login: meshtasticorg
+        run: |
+          sudo tee /etc/meshtastic-dput.cf >/dev/null <<EOF
+          [ppa]
+          fqdn                    = ppa.launchpad.net
+          method                  = ftp
+          incoming                = ~%(ppa)s
+          login                   = anonymous
+
+          [ssh-ppa]
+          fqdn                    = ppa.launchpad.net
+          method                  = sftp
+          incoming                = ~%(ssh-ppa)s
+          login                   = ${ppa_login}
+          EOF
+
+      - name: Import SSH key
+        uses: webfactory/ssh-agent@v0.10.0
+        with:
+          ssh-private-key: ${{ secrets.PPA_SFTP_PRIVATE_KEY }}
+        id: ssh
+
+      - name: Publish with dput (sftp)
+        timeout-minutes: 30 # dput is terrible, sometimes runs 'forever'
+        env:
+          up_ppa_repo: ${{ inputs.ppa_repo }}
+          up_series: ${{ inputs.series }}
+          up_version: ${{ steps.version.outputs.deb }}
+        run: >
+          dput -c /etc/meshtastic-dput.cf
+          ssh-${up_ppa_repo}
+          meshtasticd_${up_version}~${up_series}_source.changes

.github/workflows/pr_enforce_labels.yml

@@ -13,7 +13,7 @@ jobs:
     runs-on: ubuntu-latest
     steps:
       - name: Check for PR labels
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         with:
           script: |
             const labels = context.payload.pull_request.labels.map(label => label.name);

.github/workflows/pr_tests.yml

@@ -177,7 +177,7 @@ jobs:
 
       - name: Comment test results on PR
         if: github.event_name == 'pull_request' && needs.native-tests.result != 'skipped'
-        uses: actions/github-script@v8
+        uses: actions/github-script@v9
         with:
           script: |
             const fs = require('fs');

.github/workflows/tests.yml

@@ -52,7 +52,7 @@ jobs:
           node-version: 24
 
       - name: Setup pnpm
-        uses: pnpm/action-setup@v5
+        uses: pnpm/action-setup@v6
         with:
           version: latest
 

.trunk/trunk.yaml

@@ -8,10 +8,10 @@ plugins:
       uri: https://github.com/trunk-io/plugins
 lint:
   enabled:
-    - checkov@3.2.513
+    - checkov@3.2.517
-    - renovate@43.104.6
+    - renovate@43.110.9
     - prettier@3.8.1
-    - trufflehog@3.94.2
+    - trufflehog@3.94.3
     - yamllint@1.38.0
     - bandit@1.9.4
     - trivy@0.69.3

bin/config.d/lora-ecb41-pge-MeshAdv-900M30S.yaml

@@ -0,0 +1,39 @@
+# MeshAdv-Pi E22-900M30S
+# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
+Meta:
+  name: MeshAdv-Pi E22-900M30S
+  support: community
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262
+  CS: # GPIO0_A1 (physical 40)
+    pin: 1
+    gpiochip: 0
+    line: 1
+  IRQ: # GPIO0_A3 (physical 36)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  Busy: # GPIO0_A0 (physical 38)
+    pin: 0
+    gpiochip: 0
+    line: 0
+  Reset: # GPIO0_B4 (physical 12)
+    pin: 12
+    gpiochip: 0
+    line: 12
+  TXen: # GPIO1_D1 (physical 33)
+    pin: 57
+    gpiochip: 1
+    line: 25
+  RXen: # GPIO1_B3 (physical 32)
+    pin: 43
+    gpiochip: 1
+    line: 11
+  DIO3_TCXO_VOLTAGE: true
+  # Only for E22-900M33S:
+  # Limit the output power to 8 dBm
+  # SX126X_MAX_POWER: 8
+  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-MeshAdv-Mini-900M22S.yaml

@@ -0,0 +1,33 @@
+# MeshAdv Mini E22-900M22S
+# https://github.com/chrismyers2000/MeshAdv-Mini
+Meta:
+  name: MeshAdv Mini E22-900M22S
+  support: community
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262 # Ebyte E22-900M22S
+  CS: # GPIO0_B6 (physical 24, SPI1_CSN0)
+    pin: 14
+    gpiochip: 0
+    line: 14
+  IRQ: # GPIO0_A3 (physical 36)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  Busy: # GPIO0_A0 (physical 38)
+    pin: 0
+    gpiochip: 0
+    line: 0
+  Reset: # GPIO1_C3 (physical 18)
+    pin: 51
+    gpiochip: 1
+    line: 19
+  RXen: # GPIO1_B3 (physical 32)
+    pin: 43
+    gpiochip: 1
+    line: 11
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot1.yaml

@@ -0,0 +1,38 @@
+Meta:
+  name: RAK6421 + RAK13300 Slot 1
+  support: community # Promote when tested
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_A5 (IO6, physical 15)
+    pin: 5
+    gpiochip: 0
+    line: 5
+  Reset: # GPIO0_A3 (IO4, physical 36)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  Busy: # GPIO1_C3 (IO5, physical 18)
+    pin: 51
+    gpiochip: 1
+    line: 19
+  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
+  #   pin: 50
+  #   gpiochip: 1
+  #   line: 18
+  Enable_Pins:
+    - pin: 43 # GPIO1_B3 (physical 32)
+      gpiochip: 1
+      line: 11
+    - pin: 57 # GPIO1_D1 (physical 33)
+      gpiochip: 1
+      line: 25
+  DIO3_TCXO_VOLTAGE: true
+  DIO2_AS_RF_SWITCH: true
+  spidev: spidev0.0
+  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
+  #   pin: 14
+  #   gpiochip: 0
+  #   line: 14

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot2.yaml

@@ -0,0 +1,36 @@
+Meta:
+  name: RAK6421 + RAK13300 Slot 2
+  support: community # Promote when tested
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_B4 (IO6, physical 12)
+    pin: 12
+    gpiochip: 0
+    line: 12
+  Reset: # GPIO1_C3 (IO4, physical 18)
+    pin: 51
+    gpiochip: 1
+    line: 19
+  Busy: # GPIO0_B3 (IO5, physical 35)
+    pin: 11
+    gpiochip: 0
+    line: 11
+  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
+  #   pin: 50
+  #   gpiochip: 1
+  #   line: 18
+  Enable_Pins:
+    - pin: 2 # GPIO0_A2 (physical 37)
+      gpiochip: 0
+      line: 2
+    - pin: 50 # GPIO1_C2 (physical 16)
+      gpiochip: 1
+      line: 18
+  spidev: spidev0.1
+  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
+  #   pin: 7
+  #   gpiochip: 0
+  #   line: 7

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot1.yaml

@@ -0,0 +1,39 @@
+Meta:
+  name: RAK6421 + RAK13302 Slot 1
+  support: community # Promote when tested
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_A5 (IO6, physical 15)
+    pin: 5
+    gpiochip: 0
+    line: 5
+  Reset: # GPIO0_A3 (IO4, physical 36)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  Busy: # GPIO1_C3 (IO5, physical 18)
+    pin: 51
+    gpiochip: 1
+    line: 19
+  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
+  #   pin: 50
+  #   gpiochip: 1
+  #   line: 18
+  Enable_Pins:
+    - pin: 43 # GPIO1_B3 (physical 32)
+      gpiochip: 1
+      line: 11
+    - pin: 57 # GPIO1_D1 (physical 33)
+      gpiochip: 1
+      line: 25
+  DIO3_TCXO_VOLTAGE: true
+  DIO2_AS_RF_SWITCH: true
+  spidev: spidev0.0
+  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
+  #   pin: 14
+  #   gpiochip: 0
+  #   line: 14
+  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot2.yaml

@@ -0,0 +1,37 @@
+Meta:
+  name: RAK6421 + RAK13302 Slot 2
+  support: community # Promote when tested
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_B4 (IO6, physical 12)
+    pin: 12
+    gpiochip: 0
+    line: 12
+  Reset: # GPIO1_C3 (IO4, physical 18)
+    pin: 51
+    gpiochip: 1
+    line: 19
+  Busy: # GPIO0_B3 (IO5, physical 35)
+    pin: 11
+    gpiochip: 0
+    line: 11
+  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
+  #   pin: 50
+  #   gpiochip: 1
+  #   line: 18
+  Enable_Pins:
+    - pin: 2 # GPIO0_A2 (physical 37)
+      gpiochip: 0
+      line: 2
+    - pin: 50 # GPIO1_C2 (physical 16)
+      gpiochip: 1
+      line: 18
+  spidev: spidev0.1
+  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
+  #   pin: 7
+  #   gpiochip: 0
+  #   line: 7
+  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-waveshare-sxxx.yaml

@@ -0,0 +1,30 @@
+Meta:
+  name: Waveshare SX1262
+  support: deprecated
+  compatible:
+    - ebyte-ecb41-pge # Armbian
+
+Lora:
+  Module: sx1262  # Waveshare SX126X XXXM
+  DIO2_AS_RF_SWITCH: true
+  CS: # GPIO0_A1 (physical 40)
+    pin: 1
+    gpiochip: 0
+    line: 1
+  IRQ: # GPIO0_A3 (physical 36)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  Busy: # GPIO0_A0 (physical 38)
+    pin: 0
+    gpiochip: 0
+    line: 0
+  Reset: # GPIO0_B4 (physical 12)
+    pin: 12
+    gpiochip: 0
+    line: 12
+  SX126X_ANT_SW: # GPIO1_B2 (physical 31)
+    pin: 42
+    gpiochip: 1
+    line: 10
+  spidev: spidev0.0

bin/config.d/lora-ok3506-MeshAdv-900M30S.yaml

@@ -0,0 +1,41 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+# MeshAdv-Pi E22-900M30S
+# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
+Meta:
+  name: MeshAdv-Pi E22-900M30S
+  support: community
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262
+  CS: # GPIO0_B0 (physical 40)
+    pin: 8
+    gpiochip: 0
+    line: 8
+  IRQ: # GPIO3_B0 (physical 36)
+    pin: 104
+    gpiochip: 3
+    line: 8
+  Busy: # GPIO0_B1 (physical 38)
+    pin: 9
+    gpiochip: 0
+    line: 9
+  Reset: # GPIO0_B6 (physical 12)
+    pin: 14
+    gpiochip: 0
+    line: 14
+  TXen: # GPIO0_A3 (physical 33)
+    pin: 3
+    gpiochip: 0
+    line: 3
+  RXen: # GPIO0_A2 (physical 32)
+    pin: 2
+    gpiochip: 0
+    line: 2
+  DIO3_TCXO_VOLTAGE: true
+  # Only for E22-900M33S:
+  # Limit the output power to 8 dBm
+  # SX126X_MAX_POWER: 8
+  spidev: spidev0.0

bin/config.d/lora-ok3506-MeshAdv-Mini-900M22S.yaml

@@ -0,0 +1,35 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+# MeshAdv Mini E22-900M22S
+# https://github.com/chrismyers2000/MeshAdv-Mini
+Meta:
+  name: MeshAdv Mini E22-900M22S
+  support: community
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262 # Ebyte E22-900M22S
+  CS: # GPIO0_C3 (physical 24, SPI0_CSN0)
+    pin: 19
+    gpiochip: 0
+    line: 19
+  IRQ: # GPIO3_B0 (physical 36)
+    pin: 104
+    gpiochip: 3
+    line: 8
+  Busy: # GPIO0_B1 (physical 38)
+    pin: 9
+    gpiochip: 0
+    line: 9
+  Reset: # GPIO3_A6 (physical 18)
+    pin: 102
+    gpiochip: 3
+    line: 6
+  RXen: # GPIO0_A2 (physical 32)
+    pin: 2
+    gpiochip: 0
+    line: 2
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  spidev: spidev0.0

bin/config.d/lora-ok3506-RAK6421-13300-slot1.yaml

@@ -0,0 +1,40 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+Meta:
+  name: RAK6421 + RAK13300 Slot 1
+  support: community # Promote when tested
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO3_B5 (IO6, physical 15)
+    pin: 109
+    gpiochip: 3
+    line: 13
+  Reset: # GPIO3_B0 (IO4, physical 36)
+    pin: 104
+    gpiochip: 3
+    line: 8
+  Busy: # GPIO3_A6 (IO5, physical 18)
+    pin: 102
+    gpiochip: 3
+    line: 6
+  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
+  #   pin: 3
+  #   gpiochip: 0
+  #   line: 3
+  Enable_Pins:
+    - pin: 2 # GPIO0_A2 (physical 32)
+      gpiochip: 0
+      line: 2
+    - pin: 3 # GPIO0_A3 (physical 33)
+      gpiochip: 0
+      line: 3
+  DIO3_TCXO_VOLTAGE: true
+  DIO2_AS_RF_SWITCH: true
+  spidev: spidev0.0
+  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
+  #   pin: 19
+  #   gpiochip: 0
+  #   line: 19

bin/config.d/lora-ok3506-RAK6421-13300-slot2.yaml

@@ -0,0 +1,38 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+Meta:
+  name: RAK6421 + RAK13300 Slot 2
+  support: community # Promote when tested
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_B6 (IO6, physical 12)
+    pin: 14
+    gpiochip: 0
+    line: 14
+  Reset: # GPIO3_A6 (IO4, physical 18)
+    pin: 102
+    gpiochip: 3
+    line: 6
+  Busy: # GPIO0_B2 (IO5, physical 35)
+    pin: 10
+    gpiochip: 0
+    line: 10
+  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
+  #   pin: 103
+  #   gpiochip: 3
+  #   line: 7
+  Enable_Pins:
+    - pin: 106 # GPIO3_B2 (physical 37)
+      gpiochip: 3
+      line: 10
+    - pin: 103 # GPIO3_A7 (physical 16)
+      gpiochip: 3
+      line: 7
+  spidev: spidev0.1
+  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
+  #   pin: 15
+  #   gpiochip: 0
+  #   line: 15

bin/config.d/lora-ok3506-RAK6421-13302-slot1.yaml

@@ -0,0 +1,41 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+Meta:
+  name: RAK6421 + RAK13302 Slot 1
+  support: community # Promote when tested
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO3_B5 (IO6, physical 15)
+    pin: 109
+    gpiochip: 3
+    line: 13
+  Reset: # GPIO3_B0 (IO4, physical 36)
+    pin: 104
+    gpiochip: 3
+    line: 8
+  Busy: # GPIO3_A6 (IO5, physical 18)
+    pin: 102
+    gpiochip: 3
+    line: 6
+  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
+  #   pin: 3
+  #   gpiochip: 0
+  #   line: 3
+  Enable_Pins:
+    - pin: 2 # GPIO0_A2 (physical 32)
+      gpiochip: 0
+      line: 2
+    - pin: 3 # GPIO0_A3 (physical 33)
+      gpiochip: 0
+      line: 3
+  DIO3_TCXO_VOLTAGE: true
+  DIO2_AS_RF_SWITCH: true
+  spidev: spidev0.0
+  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
+  #   pin: 19
+  #   gpiochip: 0
+  #   line: 19
+  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-RAK6421-13302-slot2.yaml

@@ -0,0 +1,39 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+Meta:
+  name: RAK6421 + RAK13302 Slot 2
+  support: community # Promote when tested
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262
+  IRQ: # GPIO0_B6 (IO6, physical 12)
+    pin: 14
+    gpiochip: 0
+    line: 14
+  Reset: # GPIO3_A6 (IO4, physical 18)
+    pin: 102
+    gpiochip: 3
+    line: 6
+  Busy: # GPIO0_B2 (IO5, physical 35)
+    pin: 10
+    gpiochip: 0
+    line: 10
+  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
+  #   pin: 103
+  #   gpiochip: 3
+  #   line: 7
+  Enable_Pins:
+    - pin: 106 # GPIO3_B2 (physical 37)
+      gpiochip: 3
+      line: 10
+    - pin: 103 # GPIO3_A7 (physical 16)
+      gpiochip: 3
+      line: 7
+  spidev: spidev0.1
+  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
+  #   pin: 15
+  #   gpiochip: 0
+  #   line: 15
+  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-waveshare-sxxx.yaml

@@ -0,0 +1,32 @@
+# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
+
+Meta:
+  name: Waveshare SX1262
+  support: deprecated
+  compatible:
+    - forlinx-ok3506-s12 # Armbian
+
+Lora:
+  Module: sx1262  # Waveshare SX126X XXXM
+  DIO2_AS_RF_SWITCH: true
+  CS: # GPIO0_B0 (physical 40)
+    pin: 8
+    gpiochip: 0
+    line: 8
+  IRQ: # GPIO3_B0 (physical 36)
+    pin: 104
+    gpiochip: 3
+    line: 8
+  Busy: # GPIO0_B1 (physical 38)
+    pin: 9
+    gpiochip: 0
+    line: 9
+  Reset: # GPIO0_B6 (physical 12)
+    pin: 14
+    gpiochip: 0
+    line: 14
+  SX126X_ANT_SW: # GPIO3_B3 (physical 31)
+    pin: 107
+    gpiochip: 3
+    line: 11
+  spidev: spidev0.0

bin/generate_release_notes.py

@@ -1,25 +1,31 @@
 #!/usr/bin/env python3
-"""
+"""Generate release notes from the actual release commit range."""
-Generate release notes from merged PRs on develop and master branches.
-Categorizes PRs into Enhancements and Bug Fixes/Maintenance sections.
-"""
 
-import subprocess
+import argparse
-import re
 import json
+import re
+import subprocess
 import sys
-from datetime import datetime
 
 
-def get_last_release_tag():
+def get_last_release_tag(compare_ref, exclude_tag=None):
-    """Get the most recent release tag."""
+    """Get the most recent version tag merged into compare_ref."""
     result = subprocess.run(
-        ["git", "describe", "--tags", "--abbrev=0"],
+        ["git", "tag", "--merged", compare_ref, "--sort=-version:refname", "v*"],
         capture_output=True,
         text=True,
         check=True,
     )
-    return result.stdout.strip()
+
+    for line in result.stdout.splitlines():
+        candidate = line.strip()
+        if not candidate:
+            continue
+        if exclude_tag and candidate == exclude_tag:
+            continue
+        return candidate
+
+    raise subprocess.CalledProcessError(result.returncode, result.args, output=result.stdout, stderr=result.stderr)
 
 
 def get_tag_date(tag):
@@ -33,18 +39,18 @@ def get_tag_date(tag):
     return result.stdout.strip()
 
 
-def get_merged_prs_since_tag(tag, branch):
+def get_merged_prs_in_range(tag, compare_ref):
-    """Get all merged PRs since the given tag on the specified branch."""
+    """Get all merged PRs in the git range between tag and compare_ref."""
-    # Get commits since tag on the branch - look for PR numbers in parentheses
     result = subprocess.run(
         [
             "git",
             "log",
-            f"{tag}..origin/{branch}",
+            f"{tag}..{compare_ref}",
             "--oneline",
         ],
         capture_output=True,
         text=True,
+        check=True,
     )
 
     prs = []
@@ -65,6 +71,25 @@ def get_merged_prs_since_tag(tag, branch):
     return prs
 
 
+def parse_args():
+    """Parse CLI arguments."""
+    parser = argparse.ArgumentParser(
+        description="Generate release notes from the actual release commit range."
+    )
+    parser.add_argument("new_version", help="Version that will be tagged for this release")
+    parser.add_argument(
+        "--base-tag",
+        dest="base_tag",
+        help="Existing version tag to diff from. Defaults to the latest version tag merged into the compare ref.",
+    )
+    parser.add_argument(
+        "--compare-ref",
+        default="HEAD",
+        help="Git ref to diff to. Defaults to HEAD.",
+    )
+    return parser.parse_args()
+
+
 def get_pr_details(pr_number):
     """Get PR details from GitHub API via gh CLI."""
     try:
@@ -268,28 +293,28 @@ def get_new_contributors(pr_details_list, tag, repo="meshtastic/firmware"):
 
 
 def main():
-    if len(sys.argv) < 2:
+    args = parse_args()
-        print("Usage: generate_release_notes.py <new_version>", file=sys.stderr)
+    new_version = args.new_version
-        sys.exit(1)
+    compare_ref = args.compare_ref
-
+    current_tag = f"v{new_version}"
-    new_version = sys.argv[1]
 
     # Get last release tag
     try:
-        last_tag = get_last_release_tag()
+        last_tag = args.base_tag or get_last_release_tag(compare_ref, exclude_tag=current_tag)
     except subprocess.CalledProcessError:
         print("Error: Could not find last release tag", file=sys.stderr)
         sys.exit(1)
 
-    # Collect PRs from both branches
+    print(
-    all_pr_numbers = set()
+        f"Resolved release note range: {last_tag}..{compare_ref}",
+        file=sys.stderr,
+    )
 
-    for branch in ["develop", "master"]:
+    try:
-        try:
+        all_pr_numbers = set(get_merged_prs_in_range(last_tag, compare_ref))
-            prs = get_merged_prs_since_tag(last_tag, branch)
+    except subprocess.CalledProcessError as e:
-            all_pr_numbers.update(prs)
+        print(f"Error: Could not get PRs for range {last_tag}..{compare_ref}: {e}", file=sys.stderr)
-        except Exception as e:
+        sys.exit(1)
-            print(f"Warning: Could not get PRs from {branch}: {e}", file=sys.stderr)
 
     # Get details for all PRs
     enhancements = []

bin/org.meshtastic.meshtasticd.metainfo.xml

@@ -87,6 +87,9 @@
   </screenshots>
 
   <releases>
+    <release version="2.7.23" date="2026-04-14">
+      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.23</url>
+    </release>
     <release version="2.7.22" date="2026-04-06">
       <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.22</url>
     </release>

boards/makerfabs_pucky.json

@@ -0,0 +1,52 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "nrf52840_s140_v6.ld"
+    },
+    "core": "nRF5",
+    "cpu": "cortex-m4",
+    "extra_flags": "-DARDUINO_NRF52840_FEATHER -DNRF52840_XXAA",
+    "f_cpu": "64000000L",
+    "hwids": [
+      ["0x239A", "0x8029"],
+      ["0x239A", "0x0029"],
+      ["0x239A", "0x002A"],
+      ["0x239A", "0x802A"]
+    ],
+    "usb_product": "makerfabs_pucky",
+    "mcu": "nrf52840",
+    "variant": "makerfabs_pucky",
+    "bsp": {
+      "name": "adafruit"
+    },
+    "softdevice": {
+      "sd_flags": "-DS140",
+      "sd_name": "s140",
+      "sd_version": "6.1.1",
+      "sd_fwid": "0x00B6"
+    },
+    "bootloader": {
+      "settings_addr": "0xFF000"
+    }
+  },
+  "connectivity": ["bluetooth"],
+  "debug": {
+    "jlink_device": "nRF52840_xxAA",
+    "svd_path": "nrf52840.svd",
+    "openocd_target": "nrf52840-mdk-rs"
+  },
+  "frameworks": ["arduino", "freertos"],
+  "name": "makerfabs_pucky",
+  "upload": {
+    "maximum_ram_size": 248832,
+    "maximum_size": 815104,
+    "speed": 115200,
+    "protocol": "nrfutil",
+    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
+    "use_1200bps_touch": true,
+    "require_upload_port": true,
+    "wait_for_upload_port": true
+  },
+  "url": "https://www.makerfabs.com",
+  "vendor": "Makerfabs"
+}

debian/changelog

@@ -1,3 +1,9 @@
+meshtasticd (2.7.23.0) unstable; urgency=medium
+
+  * Version 2.7.23
+
+ -- GitHub Actions <github-actions[bot]@users.noreply.github.com>  Tue, 14 Apr 2026 12:29:48 +0000
+
 meshtasticd (2.7.22.0) unstable; urgency=medium
 
   * Version 2.7.22

platformio.ini

@@ -131,107 +131,115 @@ lib_deps =
 ; Common libs for environmental measurements in telemetry module
 [environmental_base]
 lib_deps =
-	# renovate: datasource=custom.pio depName=Adafruit BusIO packageName=adafruit/library/Adafruit BusIO
+	# renovate: datasource=github-tags depName=Adafruit BusIO packageName=adafruit/Adafruit_BusIO
-	adafruit/Adafruit BusIO@1.17.4
+	https://github.com/adafruit/Adafruit_BusIO/archive/refs/tags/1.17.4.zip
-	# renovate: datasource=custom.pio depName=Adafruit Unified Sensor packageName=adafruit/library/Adafruit Unified Sensor
+	# renovate: datasource=github-tags depName=Adafruit Unified Sensor packageName=adafruit/Adafruit_Sensor
-	adafruit/Adafruit Unified Sensor@1.1.15
+	https://github.com/adafruit/Adafruit_Sensor/archive/refs/tags/1.1.15.zip
-	# renovate: datasource=custom.pio depName=Adafruit BMP280 packageName=adafruit/library/Adafruit BMP280 Library
+	# renovate: datasource=github-tags depName=Adafruit GFX packageName=adafruit/Adafruit-GFX-Library
-	adafruit/Adafruit BMP280 Library@3.0.0
+	https://github.com/adafruit/Adafruit-GFX-Library/archive/refs/tags/1.12.6.zip
-	# renovate: datasource=custom.pio depName=Adafruit BMP085 packageName=adafruit/library/Adafruit BMP085 Library
+	# renovate: datasource=github-tags depName=NeoPixel packageName=adafruit/Adafruit_NeoPixel
-	adafruit/Adafruit BMP085 Library@1.2.4
+	https://github.com/adafruit/Adafruit_NeoPixel/archive/refs/tags/1.15.4.zip
-	# renovate: datasource=custom.pio depName=Adafruit BME280 packageName=adafruit/library/Adafruit BME280 Library
+	# renovate: datasource=github-tags depName=Adafruit SSD1306 packageName=adafruit/Adafruit_SSD1306
-	adafruit/Adafruit BME280 Library@2.3.0
+	https://github.com/adafruit/Adafruit_SSD1306/archive/refs/tags/2.5.16.zip
-	# renovate: datasource=custom.pio depName=Adafruit DPS310 packageName=adafruit/library/Adafruit DPS310
+	# renovate: datasource=github-tags depName=Adafruit BMP280 packageName=adafruit/Adafruit_BMP280_Library
-	adafruit/Adafruit DPS310@1.1.6
+	https://github.com/adafruit/Adafruit_BMP280_Library/archive/refs/tags/3.0.0.zip
-	# renovate: datasource=custom.pio depName=Adafruit MCP9808 packageName=adafruit/library/Adafruit MCP9808 Library
+	# renovate: datasource=github-tags depName=Adafruit BMP085 packageName=adafruit/Adafruit-BMP085-Library
-	adafruit/Adafruit MCP9808 Library@2.0.2
+	https://github.com/adafruit/Adafruit-BMP085-Library/archive/refs/tags/1.2.4.zip
-	# renovate: datasource=custom.pio depName=Adafruit INA260 packageName=adafruit/library/Adafruit INA260 Library
+	# renovate: datasource=github-tags depName=Adafruit BME280 packageName=adafruit/Adafruit_BME280_Library
-	adafruit/Adafruit INA260 Library@1.5.3
+	https://github.com/adafruit/Adafruit_BME280_Library/archive/refs/tags/2.3.0.zip
-	# renovate: datasource=custom.pio depName=Adafruit INA219 packageName=adafruit/library/Adafruit INA219
+	# renovate: datasource=github-tags depName=Adafruit DPS310 packageName=adafruit/Adafruit_DPS310
-	adafruit/Adafruit INA219@1.2.3
+	https://github.com/adafruit/Adafruit_DPS310/archive/refs/tags/1.1.6.zip
-	# renovate: datasource=custom.pio depName=Adafruit MPU6050 packageName=adafruit/library/Adafruit MPU6050
+	# renovate: datasource=github-tags depName=Adafruit SH110x packageName=adafruit/Adafruit_SH110x
-	adafruit/Adafruit MPU6050@2.2.9
+	https://github.com/adafruit/Adafruit_SH110x/archive/refs/tags/2.1.14.zip
-	# renovate: datasource=custom.pio depName=Adafruit LIS3DH packageName=adafruit/library/Adafruit LIS3DH
+	# renovate: datasource=github-tags depName=Adafruit MCP9808 packageName=adafruit/Adafruit_MCP9808_Library
-	adafruit/Adafruit LIS3DH@1.3.0
+	https://github.com/adafruit/Adafruit_MCP9808_Library/archive/refs/tags/2.0.2.zip
-	# renovate: datasource=custom.pio depName=Adafruit AHTX0 packageName=adafruit/library/Adafruit AHTX0
+	# renovate: datasource=github-tags depName=Adafruit INA260 packageName=adafruit/Adafruit_INA260
-	adafruit/Adafruit AHTX0@2.0.6
+	https://github.com/adafruit/Adafruit_INA260/archive/refs/tags/1.5.3.zip
-	# renovate: datasource=custom.pio depName=Adafruit LSM6DS packageName=adafruit/library/Adafruit LSM6DS
+	# renovate: datasource=github-tags depName=Adafruit INA219 packageName=adafruit/Adafruit_INA219
-	adafruit/Adafruit LSM6DS@4.7.4
+	https://github.com/adafruit/Adafruit_INA219/archive/refs/tags/1.2.3.zip
-	# renovate: datasource=custom.pio depName=Adafruit TSL2591 packageName=adafruit/library/Adafruit TSL2591 Library
+	# renovate: datasource=github-tags depName=Adafruit MPU6050 packageName=adafruit/Adafruit_MPU6050
-	adafruit/Adafruit TSL2591 Library@1.4.5
+	https://github.com/adafruit/Adafruit_MPU6050/archive/refs/tags/2.2.9.zip
-	# renovate: datasource=custom.pio depName=EmotiBit MLX90632 packageName=emotibit/library/EmotiBit MLX90632
+	# renovate: datasource=github-tags depName=Adafruit LIS3DH packageName=adafruit/Adafruit_LIS3DH
-	emotibit/EmotiBit MLX90632@1.0.8
+	https://github.com/adafruit/Adafruit_LIS3DH/archive/refs/tags/1.3.0.zip
-	# renovate: datasource=custom.pio depName=Adafruit MLX90614 packageName=adafruit/library/Adafruit MLX90614 Library
+	# renovate: datasource=github-tags depName=Adafruit AHTX0 packageName=adafruit/Adafruit_AHTX0
-	adafruit/Adafruit MLX90614 Library@2.1.6
+	https://github.com/adafruit/Adafruit_AHTX0/archive/refs/tags/2.0.6.zip
+	# renovate: datasource=github-tags depName=Adafruit LSM6DS packageName=adafruit/Adafruit_LSM6DS
+	https://github.com/adafruit/Adafruit_LSM6DS/archive/refs/tags/4.7.4.zip
+	# renovate: datasource=github-tags depName=Adafruit TSL2591 packageName=adafruit/Adafruit_TSL2591_Library
+	https://github.com/adafruit/Adafruit_TSL2591_Library/archive/refs/tags/1.4.5.zip
+	# renovate: datasource=github-tags depName=EmotiBit MLX90632 packageName=emotibit/EmotiBit_MLX90632
+	https://github.com/EmotiBit/EmotiBit_MLX90632/archive/refs/tags/v1.0.8.zip
+	# renovate: datasource=github-tags depName=Adafruit MLX90614 packageName=adafruit/Adafruit_MLX90614
+	https://github.com/adafruit/Adafruit-MLX90614-Library/archive/refs/tags/2.1.6.zip
 	# renovate: datasource=git-refs depName=INA3221 packageName=https://github.com/sgtwilko/INA3221 gitBranch=FixOverflow
 	https://github.com/sgtwilko/INA3221/archive/bb03d7e9bfcc74fc798838a54f4f99738f29fc6a.zip
-	# renovate: datasource=custom.pio depName=QMC5883L Compass packageName=mprograms/library/QMC5883LCompass
+	# renovate: datasource=github-tags depName=QMC5883L Compass packageName=mprograms/QMC5883LCompass
-	mprograms/QMC5883LCompass@1.2.3
+	https://github.com/mprograms/QMC5883LCompass/archive/refs/tags/v1.2.3.zip
-	# renovate: datasource=custom.pio depName=DFRobot_RTU packageName=dfrobot/library/DFRobot_RTU
+	# renovate: datasource=github-tags depName=DFRobot_RTU packageName=dfrobot/DFRobot_RTU
-	dfrobot/DFRobot_RTU@1.0.6
+	https://github.com/DFRobot/DFRobot_RTU/archive/refs/tags/V1.0.6.zip
 	# renovate: datasource=git-refs depName=DFRobot_RainfallSensor packageName=https://github.com/DFRobot/DFRobot_RainfallSensor gitBranch=master
 	https://github.com/DFRobot/DFRobot_RainfallSensor/archive/38fea5e02b40a5430be6dab39a99a6f6347d667e.zip
-	# renovate: datasource=custom.pio depName=INA226 packageName=robtillaart/library/INA226
+	# renovate: datasource=github-tags depName=INA226 packageName=robtillaart/INA226
-	robtillaart/INA226@0.6.6
+	https://github.com/RobTillaart/INA226/archive/refs/tags/0.6.6.zip
-	# renovate: datasource=custom.pio depName=SparkFun MAX3010x packageName=sparkfun/library/SparkFun MAX3010x Pulse and Proximity Sensor Library
+	# renovate: datasource=github-tags depName=SparkFun MAX3010x packageName=sparkfun/SparkFun_MAX3010x_Sensor_Library
-	sparkfun/SparkFun MAX3010x Pulse and Proximity Sensor Library@1.1.2
+	https://github.com/sparkfun/SparkFun_MAX3010x_Sensor_Library/archive/refs/tags/v1.1.2.zip
-	# renovate: datasource=custom.pio depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/library/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library
+	# renovate: datasource=github-tags depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/SparkFun_ICM-20948_ArduinoLibrary
-	sparkfun/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library@1.3.2
+	https://github.com/sparkfun/SparkFun_ICM-20948_ArduinoLibrary/archive/refs/tags/v1.3.2.zip
-	# renovate: datasource=custom.pio depName=Adafruit LTR390 Library packageName=adafruit/library/Adafruit LTR390 Library
+	# renovate: datasource=github-tags depName=Adafruit LTR390 Library packageName=adafruit/Adafruit_LTR390
-	adafruit/Adafruit LTR390 Library@1.1.2
+	https://github.com/adafruit/Adafruit_LTR390/archive/refs/tags/1.1.2.zip
-	# renovate: datasource=custom.pio depName=Adafruit PCT2075 packageName=adafruit/library/Adafruit PCT2075
+	# renovate: datasource=github-tags depName=Adafruit PCT2075 packageName=adafruit/Adafruit_PCT2075
-	adafruit/Adafruit PCT2075@1.0.6
+	https://github.com/adafruit/Adafruit_PCT2075/archive/refs/tags/1.0.6.zip
-	# renovate: datasource=custom.pio depName=DFRobot_BMM150 packageName=dfrobot/library/DFRobot_BMM150
+	# renovate: datasource=github-tags depName=DFRobot_BMM150 packageName=dfrobot/DFRobot_BMM150
-	dfrobot/DFRobot_BMM150@1.0.0
+	https://github.com/DFRobot/DFRobot_BMM150/archive/refs/tags/V1.0.0.zip
-	# renovate: datasource=custom.pio depName=Adafruit_TSL2561 packageName=adafruit/library/Adafruit TSL2561
+	# renovate: datasource=github-tags depName=Adafruit_TSL2561 packageName=adafruit/Adafruit_TSL2561
-	adafruit/Adafruit TSL2561@1.1.3
+	https://github.com/adafruit/Adafruit_TSL2561/archive/refs/tags/1.1.3.zip
-	# renovate: datasource=custom.pio depName=BH1750_WE packageName=wollewald/library/BH1750_WE
+	# renovate: datasource=github-tags depName=BH1750_WE packageName=wollewald/BH1750_WE
-	wollewald/BH1750_WE@1.1.10
+	https://github.com/wollewald/BH1750_WE/archive/refs/tags/1.1.10.zip
 
 ; Common environmental sensor libraries (not included in native / portduino)
 [environmental_extra_common]
 lib_deps =
-	# renovate: datasource=custom.pio depName=Adafruit BMP3XX packageName=adafruit/library/Adafruit BMP3XX Library
+	# renovate: datasource=github-tags depName=Adafruit BMP3XX packageName=adafruit/Adafruit_BMP3XX
-	adafruit/Adafruit BMP3XX Library@2.1.6
+	https://github.com/adafruit/Adafruit_BMP3XX/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=custom.pio depName=Adafruit MAX1704X packageName=adafruit/library/Adafruit MAX1704X
+	# renovate: datasource=github-tags depName=Adafruit MAX1704X packageName=adafruit/Adafruit_MAX1704X
-	adafruit/Adafruit MAX1704X@1.0.3
+	https://github.com/adafruit/Adafruit_MAX1704X/archive/refs/tags/1.0.3.zip
-	# renovate: datasource=custom.pio depName=Adafruit SHTC3 packageName=adafruit/library/Adafruit SHTC3 Library
+	# renovate: datasource=github-tags depName=Adafruit SHTC3 packageName=adafruit/Adafruit_SHTC3
-	adafruit/Adafruit SHTC3 Library@1.0.2
+	https://github.com/adafruit/Adafruit_SHTC3/archive/refs/tags/1.0.2.zip
-	# renovate: datasource=custom.pio depName=Adafruit LPS2X packageName=adafruit/library/Adafruit LPS2X
+	# renovate: datasource=github-tags depName=Adafruit LPS2X packageName=adafruit/Adafruit_LPS2X
-	adafruit/Adafruit LPS2X@2.0.6
+	https://github.com/adafruit/Adafruit_LPS2X/archive/refs/tags/2.0.6.zip
-	# renovate: datasource=custom.pio depName=Adafruit SHT31 packageName=adafruit/library/Adafruit SHT31 Library
+	# renovate: datasource=github-tags depName=Adafruit SHT31 packageName=adafruit/Adafruit_SHT31
-	adafruit/Adafruit SHT31 Library@2.2.2
+	https://github.com/adafruit/Adafruit_SHT31/archive/refs/tags/2.2.2.zip
-	# renovate: datasource=custom.pio depName=Adafruit VEML7700 packageName=adafruit/library/Adafruit VEML7700 Library
+	# renovate: datasource=github-tags depName=Adafruit VEML7700 packageName=adafruit/Adafruit_VEML7700
-	adafruit/Adafruit VEML7700 Library@2.1.6
+	https://github.com/adafruit/Adafruit_VEML7700/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=custom.pio depName=Adafruit SHT4x packageName=adafruit/library/Adafruit SHT4x Library
+	# renovate: datasource=github-tags depName=Adafruit SHT4x packageName=adafruit/Adafruit_SHT4X
-	adafruit/Adafruit SHT4x Library@1.0.5
+	https://github.com/adafruit/Adafruit_SHT4X/archive/refs/tags/1.0.5.zip
-	# renovate: datasource=custom.pio depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/library/SparkFun Qwiic Scale NAU7802 Arduino Library
+	# renovate: datasource=github-tags depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library
-	sparkfun/SparkFun Qwiic Scale NAU7802 Arduino Library@1.0.6
+	https://github.com/sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library/archive/refs/tags/v1.0.6.zip
 	# renovate: datasource=custom.pio depName=ClosedCube OPT3001 packageName=closedcube/library/ClosedCube OPT3001
 	closedcube/ClosedCube OPT3001@1.1.2
 	# renovate: datasource=git-refs depName=meshtastic-DFRobot_LarkWeatherStation packageName=https://github.com/meshtastic/DFRobot_LarkWeatherStation gitBranch=master
 	https://github.com/meshtastic/DFRobot_LarkWeatherStation/archive/4de3a9cadef0f6a5220a8a906cf9775b02b0040d.zip
-	# renovate: datasource=custom.pio depName=Sensirion Core packageName=sensirion/library/Sensirion Core
+	# renovate: datasource=github-tags depName=Sensirion Core packageName=sensirion/arduino-core
-	sensirion/Sensirion Core@0.7.3
+	https://github.com/Sensirion/arduino-core/archive/refs/tags/0.7.3.zip
-	# renovate: datasource=custom.pio depName=Sensirion I2C SCD4x packageName=sensirion/library/Sensirion I2C SCD4x
+	# renovate: datasource=github-tags depName=Sensirion I2C SCD4x packageName=sensirion/arduino-i2c-scd4x
-	sensirion/Sensirion I2C SCD4x@1.1.0
+	https://github.com/Sensirion/arduino-i2c-scd4x/archive/refs/tags/1.1.0.zip
-	# renovate: datasource=custom.pio depName=Sensirion I2C SFA3x packageName=sensirion/library/Sensirion I2C SFA3x
+	# renovate: datasource=github-tags depName=Sensirion I2C SFA3x packageName=sensirion/arduino-i2c-sfa3x
-	sensirion/Sensirion I2C SFA3x@1.0.0
+	https://github.com/Sensirion/arduino-i2c-sfa3x/archive/refs/tags/1.0.0.zip
-	# renovate: datasource=custom.pio depName=Sensirion I2C SCD30 packageName=sensirion/library/Sensirion I2C SCD30
+	# renovate: datasource=github-tags depName=Sensirion I2C SCD30 packageName=sensirion/arduino-i2c-scd30
-	sensirion/Sensirion I2C SCD30@1.0.0
+	https://github.com/Sensirion/arduino-i2c-scd30/archive/refs/tags/1.0.0.zip
 
 ; Environmental sensors with BSEC2 (Bosch proprietary IAQ)
 [environmental_extra]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=custom.pio depName=Bosch BSEC2 packageName=boschsensortec/library/bsec2
+	# renovate: datasource=github-tags depName=Bosch BSEC2 packageName=boschsensortec/Bosch-BSEC2-Library
-	boschsensortec/bsec2@1.10.2610
+	https://github.com/boschsensortec/Bosch-BSEC2-Library/archive/refs/tags/1.10.2610.zip
-	# renovate: datasource=custom.pio depName=Bosch BME68x packageName=boschsensortec/library/BME68x Sensor Library
+	# renovate: datasource=github-tags depName=Bosch BME68x packageName=boschsensortec/Bosch-BME68x-Library
-	boschsensortec/BME68x Sensor Library@1.3.40408
+	https://github.com/boschsensortec/Bosch-BME68x-Library/archive/refs/tags/v1.3.40408.zip
 
 ; Environmental sensors without BSEC (saves ~3.5KB DRAM for original ESP32 targets)
 [environmental_extra_no_bsec]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=custom.pio depName=Adafruit_BME680 packageName=adafruit/library/Adafruit BME680 Library
+	# renovate: datasource=github-tags depName=Adafruit_BME680 packageName=adafruit/Adafruit_BME680
-	adafruit/Adafruit BME680 Library@2.0.6
+	https://github.com/adafruit/Adafruit_BME680/archive/refs/tags/2.0.6.zip

src/MessageStore.h

@@ -21,8 +21,15 @@
 // How many messages are stored (RAM + flash).
 // Define -DMESSAGE_HISTORY_LIMIT=N in build_flags to control memory usage.
 #ifndef MESSAGE_HISTORY_LIMIT
+#if defined(ARCH_ESP32) &&                                                                                                       \
+    !(defined(CONFIG_IDF_TARGET_ESP32C3) || defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32S2))
+// Baseline ESP32 (non-PSRAM variants) has limited heap; reduce message history on resource-constrained builds.
+// Override with -DMESSAGE_HISTORY_LIMIT=N if needed.
+#define MESSAGE_HISTORY_LIMIT 10
+#else
 #define MESSAGE_HISTORY_LIMIT 20
 #endif
+#endif
 
 // Internal alias used everywhere in code – do NOT redefine elsewhere.
 #define MAX_MESSAGES_SAVED MESSAGE_HISTORY_LIMIT

src/Power.cpp

@@ -473,7 +473,7 @@ class AnalogBatteryLevel : public HasBatteryLevel
 // technically speaking this should work for all(?) NRF52 boards
 // but needs testing across multiple devices. NRF52 USB would not even work if
 // VBUS was not properly connected and detected by the CPU
-#elif defined(MUZI_BASE) || defined(PROMICRO_DIY_TCXO)
+#elif defined(MUZI_BASE) || defined(PROMICRO_DIY_TCXO) || defined(HOCKEY_PUCK)
         return powerHAL_isVBUSConnected();
 #endif
         return getBattVoltage() > chargingVolt;

src/concurrency/BinarySemaphorePosix.cpp

@@ -1,10 +1,85 @@
 #include "concurrency/BinarySemaphorePosix.h"
 #include "configuration.h"
 
+#include <errno.h>
+#include <sys/time.h>
+
 #ifndef HAS_FREE_RTOS
 
 namespace concurrency
 {
+#ifdef ARCH_PORTDUINO
+
+BinarySemaphorePosix::BinarySemaphorePosix()
+{
+    if (pthread_mutex_init(&mutex, NULL) != 0) {
+        throw std::runtime_error("pthread_mutex_init failed");
+    }
+    if (pthread_cond_init(&cond, NULL) != 0) {
+        pthread_mutex_destroy(&mutex);
+        throw std::runtime_error("pthread_cond_init failed");
+    }
+    signaled = false;
+}
+
+BinarySemaphorePosix::~BinarySemaphorePosix()
+{
+    pthread_cond_destroy(&cond);
+    pthread_mutex_destroy(&mutex);
+}
+
+/**
+ * Returns false if we timed out
+ */
+bool BinarySemaphorePosix::take(uint32_t msec)
+{
+    pthread_mutex_lock(&mutex);
+
+    if (!signaled) {
+        struct timespec ts;
+        clock_gettime(CLOCK_REALTIME, &ts);
+
+        ts.tv_sec += msec / 1000;
+        ts.tv_nsec += (msec % 1000) * 1000000L;
+        if (ts.tv_nsec >= 1000000000L) {
+            ts.tv_sec += 1;
+            ts.tv_nsec -= 1000000000L;
+        }
+
+        while (!signaled) {
+            int rc = pthread_cond_timedwait(&cond, &mutex, &ts);
+            if (rc == ETIMEDOUT)
+                break;
+            if (rc != 0) {
+                // Some other error occurred
+                pthread_mutex_unlock(&mutex);
+                throw std::runtime_error("pthread_cond_timedwait failed: " + std::to_string(rc));
+            }
+        }
+    }
+
+    bool wasSignaled = signaled;
+    signaled = false; // consume the signal (binary semaphore)
+
+    pthread_mutex_unlock(&mutex);
+    return wasSignaled;
+}
+
+void BinarySemaphorePosix::give()
+{
+    pthread_mutex_lock(&mutex);
+    signaled = true;
+    pthread_cond_signal(&cond);
+    pthread_mutex_unlock(&mutex);
+}
+
+IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken)
+{
+    give();
+    if (pxHigherPriorityTaskWoken)
+        *pxHigherPriorityTaskWoken = true;
+}
+#else
 
 BinarySemaphorePosix::BinarySemaphorePosix() {}
 
@@ -22,7 +97,8 @@ bool BinarySemaphorePosix::take(uint32_t msec)
 void BinarySemaphorePosix::give() {}
 
 IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken) {}
+#endif
 
 } // namespace concurrency
 
-#endif
+#endif

src/concurrency/BinarySemaphorePosix.h

@@ -2,6 +2,10 @@
 
 #include "../freertosinc.h"
 
+#ifdef ARCH_PORTDUINO
+#include <pthread.h>
+#endif
+
 namespace concurrency
 {
 
@@ -9,7 +13,12 @@ namespace concurrency
 
 class BinarySemaphorePosix
 {
-    // SemaphoreHandle_t semaphore;
+
+#ifdef ARCH_PORTDUINO
+    pthread_mutex_t mutex;
+    pthread_cond_t cond;
+    bool signaled;
+#endif
 
   public:
     BinarySemaphorePosix();
@@ -27,4 +36,4 @@ class BinarySemaphorePosix
 
 #endif
 
-} // namespace concurrency
+} // namespace concurrency

src/graphics/EInkParallelDisplay.cpp

@@ -202,7 +202,7 @@ void EInkParallelDisplay::display(void)
 
     // Get pointers to internal buffers
     uint8_t *cur = epaper->currentBuffer();
-    uint8_t *prev = epaper->previousBuffer(); // may be NULL on first init
+    const uint8_t *prev = epaper->previousBuffer(); // may be NULL on first init
 
     // Track changed row range while converting
     int newTop = h;     // min changed row (initialized to out-of-range)

src/graphics/draw/MessageRenderer.cpp

@@ -422,6 +422,17 @@ void drawTextMessageFrame(OLEDDisplay *display, OLEDDisplayUiState *state, int16
     std::vector<bool> isMine;   // track alignment
     std::vector<bool> isHeader; // track header lines
     std::vector<AckStatus> ackForLine;
+    // Hard limit on total cached lines to prevent unbounded growth from a single long message.
+    // Reserve to the actual cache cap up front, because a single message can expand to many more
+    // wrapped display lines than a small per-message estimate would predict. For a display
+    // rendering only ~5-30 lines at a time, caching more than this limit wastes heap. Stop
+    // appending once we reach MAX_CACHED_LINES to prevent a single message from blowing out the
+    // heap.
+    constexpr size_t MAX_CACHED_LINES = 100U; // ~5-6KB for std::string overhead on 32-bit (if each ~50-60 bytes avg)
+    allLines.reserve(MAX_CACHED_LINES);
+    isMine.reserve(MAX_CACHED_LINES);
+    isHeader.reserve(MAX_CACHED_LINES);
+    ackForLine.reserve(MAX_CACHED_LINES);
 
     for (auto it = filtered.rbegin(); it != filtered.rend(); ++it) {
         const auto &m = *it;
@@ -565,16 +576,23 @@ void drawTextMessageFrame(OLEDDisplay *display, OLEDDisplayUiState *state, int16
 
         int wrapWidth = mine ? rightTextWidth : leftTextWidth;
         std::vector<std::string> wrapped = generateLines(display, "", msgText, wrapWidth);
+        // Per-message wrap-line limit: even if wrapping produces many lines, cap them to prevent
+        // a single long message from consuming most or all of the cache.
+        constexpr size_t MAX_WRAPPED_LINES_PER_MSG = 20U;
+        size_t wrappedCount = 0;
         for (auto &ln : wrapped) {
-            allLines.push_back(ln);
+            if (allLines.size() >= MAX_CACHED_LINES || wrappedCount >= MAX_WRAPPED_LINES_PER_MSG)
+                break; // Cache limit or per-message limit reached; stop adding lines from this message
+            allLines.emplace_back(std::move(ln));
             isMine.push_back(mine);
             isHeader.push_back(false);
             ackForLine.push_back(AckStatus::NONE);
+            ++wrappedCount;
         }
     }
 
     // Cache lines and heights
-    cachedLines = allLines;
+    cachedLines.swap(allLines);
     cachedHeights = calculateLineHeights(cachedLines, emotes, isHeader);
 
     std::vector<MessageBlock> blocks = buildMessageBlocks(isHeader, isMine);

src/input/CardputerKeyboard.cpp

@@ -121,7 +121,6 @@ void CardputerKeyboard::pressed(uint8_t key)
         modifierFlag = 0;
     }
 
-    uint8_t next_key = 0;
     int row = (key - 1) / 10;
     int col = (key - 1) % 10;
 

src/platform/nrf52/main-nrf52.cpp

@@ -497,6 +497,9 @@ void cpuDeepSleep(uint32_t msecToWake)
             ;
 #endif
 
+#ifdef POWER_ON_OFF
+        digitalWrite(POWER_ON_OFF, HIGH);
+#endif
         auto ok = sd_power_system_off();
         if (ok != NRF_SUCCESS) {
             LOG_ERROR("FIXME: Ignoring soft device (EasyDMA pending?) and forcing system-off!");

variants/esp32/betafpv_2400_tx_micro/platformio.ini

@@ -13,7 +13,3 @@ board_build.f_cpu = 240000000L
 upload_protocol = esptool
 ;upload_port = /dev/ttyUSB0
 upload_speed = 460800
-lib_deps =
-  ${esp32_base.lib_deps}
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4

variants/esp32c3/heltec_hru_3601/platformio.ini

@@ -5,6 +5,3 @@ build_flags =
   ${esp32c3_base.build_flags}
   -D HELTEC_HRU_3601
   -I variants/esp32c3/heltec_hru_3601
-lib_deps = ${esp32c3_base.lib_deps}
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4

variants/esp32c6/m5stack_unitc6l/platformio.ini

@@ -23,8 +23,6 @@ build_unflags =
   -D HAS_WIFI
 lib_deps =
   ${esp32c6_base.lib_deps}
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4
   # renovate: datasource=custom.pio depName=NimBLE-Arduino packageName=h2zero/library/NimBLE-Arduino
   h2zero/NimBLE-Arduino@2.3.7
 build_flags = 

variants/esp32s3/diy/my_esp32s3_diy_eink/platformio.ini

@@ -12,8 +12,6 @@ lib_deps =
   ${esp32s3_base.lib_deps}
   # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
   zinggjm/GxEPD2@1.6.8
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1

variants/esp32s3/diy/my_esp32s3_diy_oled/platformio.ini

@@ -8,10 +8,6 @@ board_build.f_cpu = 240000000L
 upload_protocol = esptool
 ;upload_port = /dev/ttyACM0
 upload_speed = 921600
-lib_deps =
-  ${esp32s3_base.lib_deps}
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1

variants/esp32s3/esp32-s3-pico/platformio.ini

@@ -24,5 +24,3 @@ build_flags = ${esp32s3_base.build_flags}
 lib_deps = ${esp32s3_base.lib_deps}
   # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
   zinggjm/GxEPD2@1.6.8
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4

variants/esp32s3/heltec_sensor_hub/platformio.ini

@@ -8,7 +8,3 @@ build_flags =
   -I variants/esp32s3/heltec_sensor_hub
   -D HELTEC_SENSOR_HUB
   -ULED_BUILTIN
-
-lib_deps = ${esp32s3_base.lib_deps}
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4

variants/esp32s3/heltec_vision_master_t190/platformio.ini

@@ -20,5 +20,5 @@ build_flags =
 lib_deps =
   ${esp32s3_base.lib_deps}
   # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
-  https://github.com/meshtastic/st7789/archive/9ee76d6b18b9a8f45a2c5cae06b1134a587691eb.zip
+  https://github.com/meshtastic/st7789/archive/a787beea5c6c8f864ba6787eb432bbefc575e6ad.zip
 upload_speed = 921600

variants/esp32s3/m5stack_cardputer_adv/platformio.ini

@@ -16,12 +16,10 @@ build_src_filter =
 lib_deps =
   ${esp32s3_base.lib_deps}
   # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
-  https://github.com/meshtastic/st7789/archive/9ee76d6b18b9a8f45a2c5cae06b1134a587691eb.zip
+  https://github.com/meshtastic/st7789/archive/a787beea5c6c8f864ba6787eb432bbefc575e6ad.zip
   # renovate: datasource=github-tags depName=pschatzmann_arduino-audio-driver packageName=pschatzmann/arduino-audio-driver
   https://github.com/pschatzmann/arduino-audio-driver/archive/v0.2.1.zip
   # renovate: datasource=git-refs depName=ESP8266Audio packageName=https://github.com/meshtastic/ESP8266Audio gitBranch=meshtastic-2.0.0-dacfix
   https://github.com/meshtastic/ESP8266Audio/archive/343024632ee78d6216907b2353fc943a62422d80.zip
   # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
   earlephilhower/ESP8266SAM@1.1.0
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4

variants/esp32s3/mini-epaper-s3/nicheGraphics.h

@@ -98,7 +98,7 @@ void setupNicheGraphics()
     buttons->setTwoWayRockerPressHandlers(
         [inkhud]() {
             bool systemHandlingInput = false;
-            for (InkHUD::SystemApplet *sa : inkhud->systemApplets) {
+            for (const InkHUD::SystemApplet *sa : inkhud->systemApplets) {
                 if (sa->handleInput) {
                     systemHandlingInput = true;
                     break;
@@ -112,7 +112,7 @@ void setupNicheGraphics()
         },
         [inkhud]() {
             bool systemHandlingInput = false;
-            for (InkHUD::SystemApplet *sa : inkhud->systemApplets) {
+            for (const InkHUD::SystemApplet *sa : inkhud->systemApplets) {
                 if (sa->handleInput) {
                     systemHandlingInput = true;
                     break;

variants/esp32s3/unphone/platformio.ini

@@ -40,8 +40,6 @@ lib_deps = ${esp32s3_base.lib_deps}
   lovyan03/LovyanGFX@1.2.19
   # TODO renovate https://gitlab.com/hamishcunningham/unphonelibrary#meshtastic@9.0.0
   https://gitlab.com/hamishcunningham/unphonelibrary/-/archive/meshtastic/unphonelibrary-meshtastic.zip
-  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
-  adafruit/Adafruit NeoPixel@1.15.4
 
 [env:unphone-tft]
 board_level = extra

variants/native/portduino.ini

@@ -2,7 +2,7 @@
 [portduino_base]
 platform =
   # renovate: datasource=git-refs depName=platform-native packageName=https://github.com/meshtastic/platform-native gitBranch=develop
-  https://github.com/meshtastic/platform-native/archive/f566d364204416cdbf298e349213f7d551f793d9.zip
+  https://github.com/meshtastic/platform-native/archive/71ed55bb95feb3c43ebde1ec1e2e17643a424c04.zip
 framework = arduino
 
 build_src_filter = 
@@ -34,8 +34,8 @@ lib_deps =
 	adafruit/Adafruit seesaw Library@1.7.9
   # renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main
   https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip
-  # renovate: datasource=custom.pio depName=Adafruit_BME680 packageName=adafruit/library/Adafruit BME680 Library
+  # renovate: datasource=github-tags depName=Adafruit_BME680 packageName=adafruit/Adafruit_BME680
-  adafruit/Adafruit BME680 Library@2.0.6
+  https://github.com/adafruit/Adafruit_BME680/archive/refs/tags/2.0.6.zip
 
 build_flags =
   ${arduino_base.build_flags}
@@ -59,4 +59,5 @@ build_flags =
 lib_ignore =
   Adafruit NeoPixel
   Adafruit ST7735 and ST7789 Library
+  Adafruit SSD1306
   SD

variants/nrf52840/heltec_mesh_node_t114/platformio.ini

@@ -23,4 +23,4 @@ build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_
 lib_deps = 
   ${nrf52840_base.lib_deps}
   # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
-  https://github.com/meshtastic/st7789/archive/9ee76d6b18b9a8f45a2c5cae06b1134a587691eb.zip
+  https://github.com/meshtastic/st7789/archive/a787beea5c6c8f864ba6787eb432bbefc575e6ad.zip

variants/nrf52840/heltec_mesh_solar/platformio.ini

@@ -132,4 +132,4 @@ build_flags = ${heltec_mesh_solar_base.build_flags}
 lib_deps =
   ${heltec_mesh_solar_base.lib_deps}
   # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
-  https://github.com/meshtastic/st7789/archive/9ee76d6b18b9a8f45a2c5cae06b1134a587691eb.zip
+  https://github.com/meshtastic/st7789/archive/a787beea5c6c8f864ba6787eb432bbefc575e6ad.zip

variants/nrf52840/makerfabs_pucky/platformio.ini

@@ -0,0 +1,68 @@
+[env:makerfabs_pucky]
+custom_meshtastic_hw_model = 124
+custom_meshtastic_hw_model_slug = Hockey_Puck
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Makerfabs Hockey Puck
+custom_meshtastic_images = rak4631.svg, rak4631_case.svg
+custom_meshtastic_tags = Makerfabs
+
+extends = nrf52840_base
+board = makerfabs_pucky
+board_level = pr
+board_check = true
+build_type = release
+build_flags = ${nrf52840_base.build_flags}
+  -I variants/nrf52840/makerfabs_pucky
+  -D Hockey_Puck
+  -DMESHTASTIC_USE_EINK_UI=0
+  -DMESHTASTIC_HAS_SCREEN=0
+  -DMESHTASTIC_HAS_GPS=1
+  -DRADIOLIB_EXCLUDE_SX128X=1
+  -DRADIOLIB_EXCLUDE_SX127X=1
+  -DRADIOLIB_EXCLUDE_SX126X=1
+  -DRADIOLIB_EXCLUDE_LR11X0=0
+build_src_filter = ${nrf52_base.build_src_filter} \
+  +<../variants/nrf52840/makerfabs_pucky> \
+  +<mesh/api/> \
+  +<mqtt/> \
+lib_deps = 
+  ${nrf52840_base.lib_deps}
+  ${networking_base.lib_deps}
+  # TODO renovate
+  https://github.com/meshtastic/QMA6100P_Arduino_Library/archive/14c900b8b2e4feaac5007a7e41e0c1b7f0841136.zip
+
+; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
+; Note: as of 6/2013 the serial/bootloader based programming takes approximately 30 seconds
+;upload_protocol = jlink
+
+; Allows programming and debug via the RAK NanoDAP as the default debugger tool for the RAK4631 (it is only $10!)
+; programming time is about the same as the bootloader version.
+; For information on this see the meshtastic developers documentation for "Development on the NRF52"
+[env:makerfabs_pucky_dbg]
+extends = env:makerfabs_pucky
+board_level = extra
+
+; if the builtin version of openocd has a buggy version of semihosting, so use the external version
+; platform_packages = platformio/tool-openocd@3.1200.0
+
+build_flags =
+  ${env:makerfabs_pucky.build_flags}
+  -D USE_SEMIHOSTING
+
+lib_deps =
+  ${env:makerfabs_pucky.lib_deps}
+  # TODO renovate
+  https://github.com/geeksville/Armduino-Semihosting/archive/35b538fdf208c3530c1434cd099a08e486672ee4.zip
+
+; NOTE: the pyocd support for semihosting is buggy.  So I switched to using the builtin platformio support for the stlink adapter which worked much better.
+; However the built in openocd version in platformio has buggy support for TCP to semihosting. 
+;
+; So I'm now trying the external openocd - but the openocd scripts for nrf52.cfg assume you are using a DAP adapter not an STLINK adapter.
+; In theory I could change those scripts.  But for now I'm trying going back to a DAP adapter but with the external openocd.
+
+upload_protocol = stlink
+; eventually use platformio/tool-pyocd@2.3600.0 instad
+;upload_protocol = custom
+;upload_command = pyocd flash -t nrf52840 $UPLOADERFLAGS $SOURCE

variants/nrf52840/makerfabs_pucky/rfswitch.h

@@ -0,0 +1,18 @@
+#include "RadioLib.h"
+#include "nrf.h"
+
+static const uint32_t rfswitch_dio_pins[] = {
+    RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC // RADIOLIB_LR11X0_DIO7
+};
+
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+    // mode                DIO5 DIO6 // DIO7
+    {LR11x0::MODE_STBY, {LOW, LOW}},   // { LR11x0::MODE_STBY, { LOW, LOW, LOW } },
+    {LR11x0::MODE_RX, {HIGH, LOW}},    //   { LR11x0::MODE_RX, { HIGH, LOW, LOW } },
+    {LR11x0::MODE_TX, {HIGH, HIGH}},   // { LR11x0::MODE_TX, { HIGH, HIGH, LOW } },
+    {LR11x0::MODE_TX_HP, {LOW, HIGH}}, // { LR11x0::MODE_TX_HP, { LOW, HIGH, HIGH } },
+    {LR11x0::MODE_TX_HF, {LOW, LOW}},  // { LR11x0::MODE_TX_HF, { LOW, LOW, HIGH } },
+    {LR11x0::MODE_GNSS, {LOW, LOW}},   // { LR11x0::MODE_GNSS, { LOW, LOW, LOW } },
+    {LR11x0::MODE_WIFI, {LOW, LOW}},   // { LR11x0::MODE_WIFI, { LOW, LOW, LOW } },
+    END_OF_MODE_TABLE,
+};

variants/nrf52840/makerfabs_pucky/variant.cpp

@@ -0,0 +1,46 @@
+/*
+  Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
+  Copyright (c) 2016 Sandeep Mistry All right reserved.
+  Copyright (c) 2018, Adafruit Industries (adafruit.com)
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include "variant.h"
+#include "nrf.h"
+#include "wiring_constants.h"
+#include "wiring_digital.h"
+
+const uint32_t g_ADigitalPinMap[] = {
+    // P0
+    0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+
+    // P1
+    32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
+
+void initVariant()
+{
+
+    // 3V3 Power Rail
+    pinMode(PIN_3V3_EN, OUTPUT);
+    digitalWrite(PIN_3V3_EN, HIGH);
+
+    // Power latch
+    pinMode(POWER_ON_OFF, OUTPUT);
+    digitalWrite(POWER_ON_OFF, HIGH);
+
+    // Park the unconnected LNA_CTRL_MCU net so it does not float
+    pinMode(LNA_CTRL_PIN, INPUT_PULLDOWN);
+}

variants/nrf52840/makerfabs_pucky/variant.h

@@ -0,0 +1,177 @@
+
+/*
+  Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
+  Copyright (c) 2016 Sandeep Mistry All right reserved.
+  Copyright (c) 2018, Adafruit Industries (adafruit.com)
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#ifndef _VARIANT_RAK4630_
+#define _VARIANT_RAK4630_
+
+// #define RAK4630
+
+/** Master clock frequency */
+#define VARIANT_MCK (64000000ul)
+
+#define USE_LFXO // Board uses 32khz crystal for LF
+
+/*----------------------------------------------------------------------------
+ *        Headers
+ *----------------------------------------------------------------------------*/
+
+#include "WVariant.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif // __cplusplus
+
+// Number of pins defined in PinDescription array
+#define PINS_COUNT (48)
+#define NUM_DIGITAL_PINS (48)
+#define NUM_ANALOG_INPUTS (6)
+#define NUM_ANALOG_OUTPUTS (0)
+
+// #define LED_PIN 16 // This is a LED_WS2812 not a standard LED
+#define HAS_NEOPIXEL                         // Enable the use of neopixels
+#define NEOPIXEL_COUNT 1                     // How many neopixels are connected
+#define NEOPIXEL_DATA 25                     // gpio pin used to send data to the neopixels
+#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
+
+#define RGB_LED_POWER
+
+#define LED_STATE_ON 1
+
+/*
+ * Buttons
+ */
+
+#define BUTTON_PIN 5
+#define PIN_BUZZER 22
+/*
+ * Analog pins
+ */
+#define PIN_A0 (2)
+#define PIN_A1 (3)
+#define PIN_A2 (4)
+#define PIN_A3 (5)
+#define PIN_A4 (28)
+#define PIN_A5 (29)
+#define PIN_A6 (30)
+#define PIN_A7 (31)
+
+static const uint8_t A0 = PIN_A0;
+static const uint8_t A1 = PIN_A1;
+static const uint8_t A2 = PIN_A2;
+static const uint8_t A3 = PIN_A3;
+static const uint8_t A4 = PIN_A4;
+static const uint8_t A5 = PIN_A5;
+static const uint8_t A6 = PIN_A6;
+static const uint8_t A7 = PIN_A7;
+#define ADC_RESOLUTION 14
+
+// Other pins
+#define PIN_AREF (2)
+
+static const uint8_t AREF = PIN_AREF;
+
+/*
+ * Serial interfaces
+ */
+// GPS on Base Board
+#define PIN_SERIAL1_RX (8)
+#define PIN_SERIAL1_TX (6)
+
+// DEBUG on Base Board
+#define PIN_SERIAL2_RX (38)
+#define PIN_SERIAL2_TX (37)
+
+/*
+ * SPI Interfaces
+ */
+#define SPI_INTERFACES_COUNT 1
+#define PIN_SPI_MISO (47)
+#define PIN_SPI_MOSI (46)
+#define PIN_SPI_SCK (45)
+
+static const uint8_t SS = 44;
+static const uint8_t MOSI = PIN_SPI_MOSI;
+static const uint8_t MISO = PIN_SPI_MISO;
+static const uint8_t SCK = PIN_SPI_SCK;
+
+#define USE_LR1121
+#define LR11X0_POWER_EN (13)
+#define LR1121_IRQ_PIN 14
+#define LR1121_NRESET_PIN (42)
+#define LR1121_BUSY_PIN (43)
+#define LR1121_SPI_NSS_PIN SS
+#define LR1121_SPI_SCK_PIN PIN_SPI_SCK
+#define LR1121_SPI_MOSI_PIN PIN_SPI_MOSI
+#define LR1121_SPI_MISO_PIN PIN_SPI_MISO
+#define LR11X0_DIO3_TCXO_VOLTAGE 3.3
+#define LR11X0_DIO_AS_RF_SWITCH
+
+/*
+ * Wire Interfaces
+ */
+#define WIRE_INTERFACES_COUNT 1
+#define PIN_WIRE_SDA (26)
+#define PIN_WIRE_SCL (27)
+
+#define HAS_QMA6100P
+
+/*
+ * Power Switches
+ */
+#define POWER_ON_OFF (30) // P0.30 Power latch control, set high to keep power on, set low to turn off
+#define PIN_3V3_EN (16)
+
+#define HAS_GPS 1
+#define PIN_GPS_PPS (11) // Pulse per second input from the GPS
+#define GPS_RX_PIN PIN_SERIAL1_RX
+#define GPS_TX_PIN PIN_SERIAL1_TX
+
+// Battery
+#define EXT_CHRG_DETECT (32 + 7) // P1.07
+#define HAS_CW2015 1
+
+// RAK4630 AIN0 = nrf52840 AIN3 = Pin 5
+// #define BATTERY_LPCOMP_INPUT NRF_LPCOMP_INPUT_3
+
+// We have AIN3 with a VBAT divider so AIN3 = VBAT * (1.5/2.5)
+// We have the device going deep sleep under 3.1V, which is AIN3 = 1.86V
+// So we can wake up when VBAT>=VDD is restored to 3.3V, where AIN3 = 1.98V
+// 1.98/3.3 = 6/10, but that's close to the VBAT divider, so we
+// pick 6/8VDD, which means VBAT=4.1V.
+// Reference:
+// VDD=3.3V AIN3=5/8*VDD=2.06V VBAT=1.66*AIN3=3.41V
+// VDD=3.3V AIN3=11/16*VDD=2.26V VBAT=1.66*AIN3=3.76V
+// VDD=3.3V AIN3=6/8*VDD=2.47V VBAT=1.66*AIN3=4.1V
+// #define BATTERY_LPCOMP_THRESHOLD NRF_LPCOMP_REF_SUPPLY_11_16
+
+#define LNA_CTRL_PIN 4 // P0.04
+
+#define HOCKEY_PUCK 1
+#define NUM_PA_POINTS 22
+#define TX_GAIN_LORA 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 13, 13, 13, 12, 12, 11, 10, 9, 8, 7
+
+#ifdef __cplusplus
+}
+#endif
+
+/*----------------------------------------------------------------------------
+ *        Arduino objects - C++ only
+ *----------------------------------------------------------------------------*/
+
+#endif

version.properties

@@ -1,4 +1,4 @@
 [VERSION]  
 major = 2
 minor = 7
-build = 22
+build = 23