firmware/variants/esp32p4/crowpanel-advanced-p4/platformio.ini

[env:crowpanel-advanced-p4-50]
extends = esp32p4_base
board = crowpanel-p4
board_check = true
board_build.partitions = default_16MB.csv

build_src_filter =
  ${esp32p4_base.build_src_filter}
  +<../variants/esp32p4/crowpanel-advanced-p4>

build_flags = 
  ${esp32p4_base.build_flags}
  -D CROWPANEL_ADV_P4
  -D CROWPANEL_ADV_P4_50
  -I variants/esp32p4/crowpanel-advanced-p4
  -D ARDUINO_USB_CDC_ON_BOOT=0
  -D ARDUINO_USB_MODE=1
  -D MESHTASTIC_EXCLUDE_WEBSERVER=1
  -D MESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
  -D MESHTASTIC_EXCLUDE_INPUTBROKER=1
  -D MAX_NUM_NODES=500
  -D MAX_NUM_NODES_VIEW=500
;  -DSOC_USB_OTG_SUPPORTED=1
  -D CONFIG_DISABLE_HAL_LOCKS=1 ; "feels" to be a bit more stable without locks
;  -D INPUTDRIVER_BUTTON_TYPE=0
  -D HAS_SDCARD
  -D HAS_SD_MMC
  -D BOARD_MAX_SDMMC_FREQ=100000
  -D BOARD_HAS_1BIT_SDMMC
  -D SD_SCLK_PIN=43
  -D SD_MISO_PIN=39
  -D SD_MOSI_PIN=44
  -D SD_MMC_HOST_SLOT=SDMMC_HOST_SLOT_1
  -D HAS_SCREEN=1
  -D HAS_TFT=1
;  -D USE_I2S_BUZZER
  -D RAM_SIZE=10240
  -D LV_LVGL_H_INCLUDE_SIMPLE
  -D LV_CONF_INCLUDE_SIMPLE
  -D LV_COMP_CONF_INCLUDE_SIMPLE
  -D LV_USE_SYSMON=0
  -D LV_USE_PROFILER=0
  -D LV_USE_PERF_MONITOR=0
  -D LV_USE_MEM_MONITOR=0
  -D LV_USE_LOG=0
  -D LV_CACHE_DEF_SIZE=3400000
  -D USE_LOG_DEBUG
  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
  -D RADIOLIB_SPI_PARANOID=0
  -D LGFX_SCREEN_WIDTH=800
  -D LGFX_SCREEN_HEIGHT=480
  -D DISPLAY_SIZE=800x480 ; landscape mode
  -D LGFX_DRIVER=LGFX_ELECROW_P4_50
  -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_ELECROW_P4_50.h\"
  -D LGFX_BUFSIZE=1152000
  -D LGFX_SKIP_RGB565_SWAP
  -D VIEW_320x240
  -D DISPLAY_SET_RESOLUTION
  -D USE_PACKET_API
  -D MAP_FULL_REDRAW

lib_deps =
  ${esp32p4_base.lib_deps}
  ${device-ui_base.lib_deps}
  https://github.com/lovyan03/LovyanGFX#develop

custom_sdkconfig =
  ${esp32p4_base.custom_sdkconfig}
  # Disable external SDMMC IO power control to avoid GPIO conflicts
  CONFIG_SOC_SDMMC_IO_POWER_EXTERNAL=n
  # CONFIG_BT_BLE_50_FEATURES_SUPPORTED is not set
  CONFIG_BT_BLE_42_FEATURES_SUPPORTED=y

  # Force hosted transport/target selection for this env.
  CONFIG_ESP_HOSTED_SDIO_4_BIT_BUS=y
  CONFIG_ESP_HOSTED_SDIO_CLOCK_FREQ_KHZ=40000
  # CrowPanel SDIO pins
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_CMD_SLOT_1=54
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_CLK_SLOT_1=53
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D0_SLOT_1=52
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D1_4BIT_BUS_SLOT_1=51
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D2_4BIT_BUS_SLOT_1=50
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D3_4BIT_BUS_SLOT_1=49

  # Also set resolved SDIO pins explicitly so generated sdkconfig does not
  # retain stale template values from framework sdkconfig.
  CONFIG_ESP_HOSTED_SDIO_PIN_CMD=54
  CONFIG_ESP_HOSTED_SDIO_PIN_CLK=53
  CONFIG_ESP_HOSTED_SDIO_PIN_D0=52
  CONFIG_ESP_HOSTED_SDIO_PIN_D1=51
  CONFIG_ESP_HOSTED_SDIO_PIN_D2=50
  CONFIG_ESP_HOSTED_SDIO_PIN_D3=49
  CONFIG_ESP_HOSTED_SDIO_PRIV_PIN_D1_4BIT_BUS=51

  # SDIO Slot 1 via GPIO matrix
  CONFIG_ESP_HOSTED_SDIO_SLOT_1=y
  CONFIG_ESP_HOSTED_SDIO_RESET_ACTIVE_HIGH=y
  CONFIG_ESP_HOSTED_SDIO_GPIO_RESET_SLAVE=20
  CONFIG_ESP_HOSTED_GPIO_SLAVE_RESET_SLAVE=20

[env:crowpanel-advanced-p4-70-90-101]
extends = esp32p4_base
board = esp32-p4-evboard
board_check = true
board_build.partitions = default_16MB.csv

build_src_filter =
  ${esp32p4_base.build_src_filter}
  +<../variants/esp32p4/crowpanel-advanced-p4>

build_flags =
  ${esp32p4_base.build_flags}
  -D CROWPANEL_ADV_P4
  -D CROWPANEL_ADV_P4_70_90_101
  -I variants/esp32p4/crowpanel-advanced-p4
  -D ARDUINO_USB_CDC_ON_BOOT=0
  -D ARDUINO_USB_MODE=1
  -D MESHTASTIC_EXCLUDE_WEBSERVER=1
  -D MESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
  -D MESHTASTIC_EXCLUDE_INPUTBROKER=1
  -D MAX_NUM_NODES=500
  -D MAX_NUM_NODES_VIEW=500
;  -DSOC_USB_OTG_SUPPORTED=1
  -D CONFIG_DISABLE_HAL_LOCKS=1 ; "feels" to be a bit more stable without locks
;  -D INPUTDRIVER_BUTTON_TYPE=0
  -D HAS_SDCARD
  -D HAS_SD_MMC
  -D BOARD_MAX_SDMMC_FREQ=10000
  -D BOARD_HAS_1BIT_SDMMC
  -D SD_SCLK_PIN=43
  -D SD_MISO_PIN=39
  -D SD_MOSI_PIN=44
  -D SD_MMC_HOST_SLOT=SDMMC_HOST_SLOT_0
  -D HAS_SCREEN=1
  -D HAS_TFT=1
;  -D USE_I2S_BUZZER
  -D RAM_SIZE=12288
  -D LV_LVGL_H_INCLUDE_SIMPLE
  -D LV_CONF_INCLUDE_SIMPLE
  -D LV_COMP_CONF_INCLUDE_SIMPLE
  -D LV_USE_SYSMON=1
  -D LV_USE_PROFILER=0
  -D LV_USE_PERF_MONITOR=1
  -D LV_USE_MEM_MONITOR=0
  -D LV_USE_LOG=0
  -D LV_CACHE_DEF_SIZE=5600000
  -D USE_LOG_DEBUG
  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
  -D LORA_SPI_FREQUENCY=1000000
  -D BOARD_LORA_MAX_TX_POWER=17
  -D SX126X_CURRENT_LIMIT_MA=100
  -D RADIOLIB_SPI_PARANOID=0
  -D LGFX_SCREEN_WIDTH=1024
  -D LGFX_SCREEN_HEIGHT=600
  -D DISPLAY_SIZE=1024x600 ; landscape mode
  -D LGFX_DRIVER=LGFX_ELECROW_P4_70_90_101
  -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_ELECROW_P4_70_90_101.h\"
  -D LGFX_BUFSIZE=614400
  -D VIEW_320x240
  -D DISPLAY_SET_RESOLUTION
  -D USE_PACKET_API
;  -D MAP_FULL_REDRAW

lib_deps =
  ${esp32p4_base.lib_deps}
  ${device-ui_base.lib_deps}
  https://github.com/lovyan03/LovyanGFX#develop

custom_sdkconfig =
  ${esp32p4_base.custom_sdkconfig}
  CONFIG_SOC_SDMMC_IO_POWER_EXTERNAL=n
  # CONFIG_BT_BLE_50_FEATURES_SUPPORTED is not set
  CONFIG_BT_BLE_42_FEATURES_SUPPORTED=y
  # SDIO Slot 1 via GPIO matrix
  CONFIG_ESP_HOSTED_SDIO_SLOT_1=y
  
  # 1-bit bus (proven stable on CrowPanel)
  CONFIG_ESP_HOSTED_SDIO_1_BIT_BUS=y
  CONFIG_ESP_HOSTED_SDIO_BUS_WIDTH=1
  
  # Conservative 10 MHz clock for OTA reliability
  CONFIG_ESP_HOSTED_SDIO_CLOCK_FREQ_KHZ=10000
  
  # CrowPanel SDIO pins (happen to match P4 Slot 1 defaults)
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_CLK_SLOT_1=18
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_CMD_SLOT_1=19
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D0_SLOT_1=14
  CONFIG_ESP_HOSTED_PRIV_SDIO_PIN_D1_1BIT_BUS_SLOT_1=15
  
  # Reset pin: GPIO32, active high (R77 pullup on CrowPanel)
  CONFIG_ESP_HOSTED_SDIO_RESET_ACTIVE_HIGH=y
  CONFIG_ESP_HOSTED_SDIO_GPIO_RESET_SLAVE=32
  CONFIG_ESP_HOSTED_GPIO_SLAVE_RESET_SLAVE=32