Merge branch 'master' into station-g3

Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>

.trunk/trunk.yaml

@@ -11,7 +11,7 @@ lint:
     - checkov@3.2.528
     - renovate@43.150.0
     - prettier@3.8.3
-    - trufflehog@3.95.2
+    - trufflehog@3.95.3
     - yamllint@1.38.0
     - bandit@1.9.4
     - trivy@0.70.0

bin/config.d/lora-station-g3.yaml

@@ -0,0 +1,18 @@
+# Station G3 motherboard with a Raspberry Pi Zero 2W as the MCU daughterboard.
+# Verify spidev / I2C device paths for your OS — they may differ.
+Meta:
+  name: Station G3
+  support: community
+  compatible:
+    - raspberry-pi
+
+Lora:
+  Module: sx1262
+  IRQ: 22                       # BCM pin — wiki spec
+  Reset: 16                     # BCM pin — wiki spec
+  Busy: 24                      # BCM pin — wiki spec
+  # CS: 8                       # BCM 8 = SPI0 CE0 (default); uncomment only to override
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  spidev: spidev0.0
+  # SX126X_MAX_POWER: 19        # matches Station G2 firmware cap; raise carefully per PA jumper mode

boards/ThinkNode-M7.json

@@ -0,0 +1,42 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "esp32s3_out.ld",
+      "memory_type": "qio_opi"
+    },
+    "core": "esp32",
+    "extra_flags": [
+      "-D BOARD_HAS_PSRAM",
+      "-D ARDUINO_USB_CDC_ON_BOOT=0",
+      "-D ARDUINO_USB_MODE=0",
+      "-D ARDUINO_RUNNING_CORE=1",
+      "-D ARDUINO_EVENT_RUNNING_CORE=0"
+    ],
+    "f_cpu": "240000000L",
+    "f_flash": "80000000L",
+    "flash_mode": "qio",
+    "psram_type": "qio_opi",
+    "hwids": [["0x303A", "0x1001"]],
+    "mcu": "esp32s3",
+    "variant": "ELECROW-ThinkNode-M7"
+  },
+  "connectivity": ["wifi", "bluetooth", "lora"],
+  "debug": {
+    "default_tool": "esp-builtin",
+    "onboard_tools": ["esp-builtin"],
+    "openocd_target": "esp32s3.cfg"
+  },
+  "frameworks": ["arduino", "espidf"],
+  "name": "ELECROW ThinkNode M7",
+  "upload": {
+    "flash_size": "8MB",
+    "maximum_ram_size": 524288,
+    "maximum_size": 8388608,
+    "use_1200bps_touch": true,
+    "wait_for_upload_port": true,
+    "require_upload_port": true,
+    "speed": 921600
+  },
+  "url": "https://www.elecrow.com",
+  "vendor": "ELECROW"
+}

boards/station-g3.json

@@ -0,0 +1,41 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "esp32s3_out.ld",
+      "memory_type": "qio_opi"
+    },
+    "core": "esp32",
+    "extra_flags": [
+      "-DBOARD_HAS_PSRAM",
+      "-DARDUINO_USB_CDC_ON_BOOT=1",
+      "-DARDUINO_USB_MODE=1",
+      "-DARDUINO_RUNNING_CORE=1",
+      "-DARDUINO_EVENT_RUNNING_CORE=0"
+    ],
+    "f_cpu": "240000000L",
+    "f_flash": "80000000L",
+    "flash_mode": "qio",
+    "hwids": [["0x303A", "0x1001"]],
+    "mcu": "esp32s3",
+    "variant": "station-g3"
+  },
+  "connectivity": ["wifi", "bluetooth", "lora"],
+  "debug": {
+    "default_tool": "esp-builtin",
+    "onboard_tools": ["esp-builtin"],
+    "openocd_target": "esp32s3.cfg"
+  },
+  "frameworks": ["arduino", "espidf"],
+  "name": "BQ Station G3",
+  "upload": {
+    "flash_size": "16MB",
+    "maximum_ram_size": 327680,
+    "maximum_size": 16777216,
+    "use_1200bps_touch": true,
+    "wait_for_upload_port": true,
+    "require_upload_port": true,
+    "speed": 921600
+  },
+  "url": "",
+  "vendor": "BQ Consulting"
+}

platformio.ini

@@ -138,7 +138,7 @@ lib_deps =
 	# renovate: datasource=github-tags depName=Adafruit GFX packageName=adafruit/Adafruit-GFX-Library
 	https://github.com/adafruit/Adafruit-GFX-Library/archive/refs/tags/1.12.6.zip
 	# renovate: datasource=github-tags depName=NeoPixel packageName=adafruit/Adafruit_NeoPixel
-	https://github.com/adafruit/Adafruit_NeoPixel/archive/refs/tags/1.15.4.zip
+	https://github.com/adafruit/Adafruit_NeoPixel/archive/1.15.5.zip
 	# renovate: datasource=github-tags depName=Adafruit SSD1306 packageName=adafruit/Adafruit_SSD1306
 	https://github.com/adafruit/Adafruit_SSD1306/archive/refs/tags/2.5.16.zip
 	# renovate: datasource=github-tags depName=Adafruit BMP280 packageName=adafruit/Adafruit_BMP280_Library

src/DebugConfiguration.cpp

@@ -151,7 +151,7 @@ inline bool Syslog::_sendLog(uint16_t pri, const char *appName, const char *mess
     if (!this->_enabled)
         return false;
 
-    if ((this->_server == NULL && this->_ip == INADDR_NONE) || this->_port == 0)
+    if ((this->_server == NULL && this->_ip == IPAddress(0, 0, 0, 0)) || this->_port == 0)
         return false;
 
     // Check priority against priMask values.

src/DebugConfiguration.h

@@ -13,6 +13,11 @@ extern MemGet memGet;
 #define LED_STATE_ON 1
 #endif
 
+// WIFI LED
+#ifndef WIFI_STATE_ON
+#define WIFI_STATE_ON 1
+#endif
+
 // -----------------------------------------------------------------------------
 // DEBUG
 // -----------------------------------------------------------------------------
@@ -147,7 +152,9 @@ extern "C" void logLegacy(const char *level, const char *fmt, ...);
 // Default Bluetooth PIN
 #define defaultBLEPin 123456
 
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && defined(USE_CH390D)
+#include <ESP32_CH390.h>
+#elif HAS_ETHERNET && !defined(USE_WS5500)
 #include <RAK13800_W5100S.h>
 #endif // HAS_ETHERNET
 

src/Power.cpp

@@ -878,7 +878,16 @@ void Power::readPowerStatus()
 
     // Notify any status instances that are observing us
     const PowerStatus powerStatus2 = PowerStatus(hasBattery, usbPowered, isChargingNow, batteryVoltageMv, batteryChargePercent);
-    if (millis() > lastLogTime + 50 * 1000) {
+
+    // Log battery-presence transitions once; skip OptUnknown so we don't lie before the first probe.
+    static OptionalBool prevHasBattery = OptUnknown;
+    if (hasBattery != OptUnknown && hasBattery != prevHasBattery) {
+        LOG_INFO("Power: battery hardware %s", hasBattery == OptTrue ? "detected" : "absent (USB-only)");
+        prevHasBattery = hasBattery;
+    }
+
+    // Periodic telemetry only emits when a battery is actually present (otherwise values are constant -1/0).
+    if (hasBattery == OptTrue && !Throttle::isWithinTimespanMs(lastLogTime, 50 * 1000)) {
         LOG_DEBUG("Battery: usbPower=%d, isCharging=%d, batMv=%d, batPct=%d", powerStatus2.getHasUSB(),
                   powerStatus2.getIsCharging(), powerStatus2.getBatteryVoltageMv(), powerStatus2.getBatteryChargePercent());
         lastLogTime = millis();

src/input/InputBroker.cpp

@@ -333,6 +333,12 @@ void InputBroker::Init()
             BaseType_t higherWake = 0;
             concurrency::mainDelay.interruptFromISR(&higherWake);
         };
+#if defined(ELECROW_ThinkNode_M7)
+        userConfigNoScreen.longLongPressTime = 15 * 1000;
+        userConfigNoScreen.longLongPress = INPUT_BROKER_FACTORY_RST;
+#else
+        userConfigNoScreen.longLongPress = INPUT_BROKER_SHUTDOWN;
+#endif
         userConfigNoScreen.singlePress = INPUT_BROKER_USER_PRESS;
         userConfigNoScreen.longPress = INPUT_BROKER_NONE;
         userConfigNoScreen.longPressTime = 500;

src/input/InputBroker.h

@@ -25,6 +25,7 @@ enum input_broker_event {
     INPUT_BROKER_USER_PRESS,
     INPUT_BROKER_ALT_PRESS,
     INPUT_BROKER_ALT_LONG,
+    INPUT_BROKER_FACTORY_RST = 0x9a,
     INPUT_BROKER_SHUTDOWN = 0x9b,
     INPUT_BROKER_GPS_TOGGLE = 0x9e,
     INPUT_BROKER_SEND_PING = 0xaf,

src/main.cpp

@@ -59,12 +59,12 @@ NimbleBluetooth *nimbleBluetooth = nullptr;
 NRF52Bluetooth *nrf52Bluetooth = nullptr;
 #endif
 
-#if HAS_WIFI || defined(USE_WS5500)
+#if HAS_WIFI || defined(USE_WS5500) || defined(USE_CH390D)
 #include "mesh/api/WiFiServerAPI.h"
 #include "mesh/wifi/WiFiAPClient.h"
 #endif
 
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && !defined(USE_WS5500) && !defined(USE_CH390D)
 #include "mesh/api/ethServerAPI.h"
 #include "mesh/eth/ethClient.h"
 #endif
@@ -335,7 +335,7 @@ void setup()
 
 #ifdef WIFI_LED
     pinMode(WIFI_LED, OUTPUT);
-    digitalWrite(WIFI_LED, LOW);
+    digitalWrite(WIFI_LED, HIGH ^ WIFI_STATE_ON);
 #endif
 
 #ifdef BLE_LED

src/mesh/InterfacesTemplates.cpp

@@ -25,7 +25,7 @@ template class LR11x0Interface<LR1121>;
 template class SX126xInterface<STM32WLx>;
 #endif
 
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && !defined(USE_WS5500) && !defined(USE_CH390D)
 #include "api/ethServerAPI.h"
 template class ServerAPI<EthernetClient>;
 template class APIServerPort<ethServerAPI, EthernetServer>;

src/mesh/NodeDB.cpp

@@ -80,6 +80,14 @@ static unsigned char userprefs_admin_key_1[] = USERPREFS_USE_ADMIN_KEY_1;
 static unsigned char userprefs_admin_key_2[] = USERPREFS_USE_ADMIN_KEY_2;
 #endif
 
+// Weak empty variant initialization function.
+// May be redefined by variant files.
+void variantDefaultConfig() __attribute__((weak));
+void variantDefaultConfig() {}
+
+void variantDefaultModuleConfig() __attribute__((weak));
+void variantDefaultModuleConfig() {}
+
 #ifdef HELTEC_MESH_NODE_T114
 
 uint32_t read8(uint8_t bits, uint8_t dummy, uint8_t cs, uint8_t sck, uint8_t mosi, uint8_t dc, uint8_t rst)
@@ -785,6 +793,8 @@ void NodeDB::installDefaultConfig(bool preserveKey = false)
 #endif
 
     initConfigIntervals();
+    variantDefaultConfig();
+    variantDefaultModuleConfig();
 }
 
 void NodeDB::initConfigIntervals()

src/mesh/api/ethServerAPI.cpp

@@ -1,7 +1,7 @@
 #include "configuration.h"
 #include <Arduino.h>
 
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && !defined(USE_WS5500) && !defined(USE_CH390D)
 
 #include "ethServerAPI.h"
 

src/mesh/api/ethServerAPI.h

@@ -1,7 +1,7 @@
 #pragma once
 
 #include "ServerAPI.h"
-#ifndef USE_WS5500
+#if !defined(USE_WS5500) && !defined(USE_CH390D)
 #include <RAK13800_W5100S.h>
 
 /**

src/mesh/eth/ethClient.cpp

@@ -9,7 +9,7 @@
 #include <RAK13800_W5100S.h>
 #include <SPI.h>
 
-#if HAS_NETWORKING
+#if HAS_NETWORKING && !defined(USE_WS5500) && !defined(USE_CH390D)
 
 #ifndef DISABLE_NTP
 #include <NTPClient.h>

src/mesh/generated/meshtastic/mesh.pb.h

@@ -319,6 +319,8 @@ typedef enum _meshtastic_HardwareModel {
     meshtastic_HardwareModel_HELTEC_V4_R8 = 132,
     /* The HELTEC_MESH_NODE_T1 uses an NRF52840 chip, plus an SX1262. */
     meshtastic_HardwareModel_HELTEC_MESH_NODE_T1 = 133,
+    /* B&Q Consulting Station G3: TBD */
+    meshtastic_HardwareModel_STATION_G3 = 134,
     /* ------------------------------------------------------------------------------------------------------------------------------------------
  Reserved ID For developing private Ports. These will show up in live traffic sparsely, so we can use a high number. Keep it within 8 bits.
  ------------------------------------------------------------------------------------------------------------------------------------------ */

src/mesh/wifi/WiFiAPClient.cpp

@@ -15,6 +15,12 @@
 #define ETH ETH2
 #endif // HAS_ETHERNET
 
+#if HAS_ETHERNET && defined(USE_CH390D)
+#include "ESP32_CH390.h"
+#include "hal/spi_types.h"
+#define ETH CH390
+#endif // HAS_ETHERNET
+
 #include <WiFiUdp.h>
 #ifdef ARCH_ESP32
 #if !MESHTASTIC_EXCLUDE_WEBSERVER
@@ -56,12 +62,43 @@ unsigned long lastrun_ntp = 0;
 
 bool needReconnect = true;   // If we create our reconnector, run it once at the beginning
 bool isReconnecting = false; // If we are currently reconnecting
+#if defined(USE_WS5500) || defined(USE_CH390D)
+static volatile bool ethNetworkConnectedPending = false;
+#endif
 
 WiFiUDP syslogClient;
 meshtastic::Syslog syslog(syslogClient);
 
 Periodic *wifiReconnect;
 
+#if defined(USE_WS5500) || defined(USE_CH390D)
+static void onNetworkConnected();
+static uint32_t lastEthIP = 0;
+static int32_t ethNetworkConnectedPoll()
+{
+    if (ethNetworkConnectedPending) {
+        ethNetworkConnectedPending = false;
+        uint32_t ip = (uint32_t)ETH.localIP();
+        bool ipChanged = APStartupComplete && ip != 0 && ip != lastEthIP;
+        onNetworkConnected();
+        if (ipChanged) {
+            LOG_INFO("Ethernet IP changed (%u.%u.%u.%u), restarting mDNS", ip & 0xff, (ip >> 8) & 0xff, (ip >> 16) & 0xff,
+                     (ip >> 24) & 0xff);
+            MDNS.end();
+            if (MDNS.begin("Meshtastic")) {
+                MDNS.addService("meshtastic", "tcp", SERVER_API_DEFAULT_PORT);
+                MDNS.addServiceTxt("meshtastic", "tcp", "shortname", String(owner.short_name));
+                MDNS.addServiceTxt("meshtastic", "tcp", "id", String(nodeDB->getNodeId().c_str()));
+                MDNS.addServiceTxt("meshtastic", "tcp", "pio_env", optstr(APP_ENV));
+            }
+        }
+        if (ip != 0)
+            lastEthIP = ip;
+    }
+    return 500;
+}
+#endif
+
 #ifdef USE_WS5500
 // Startup Ethernet
 bool initEthernet()
@@ -72,6 +109,38 @@ bool initEthernet()
 #if !MESHTASTIC_EXCLUDE_WEBSERVER
         createSSLCert(); // For WebServer
 #endif
+        new concurrency::Periodic("EthConnect", ethNetworkConnectedPoll);
+        return true;
+    }
+
+    return false;
+}
+#endif
+
+#ifdef USE_CH390D
+// Startup Ethernet
+bool initEthernet()
+{
+    // Configure CH390
+    ch390_config_t ch390_conf = CH390_DEFAULT_CONFIG();
+    ch390_conf.spi_host = SPI3_HOST;
+    ch390_conf.spi_cs_gpio = ETH_CS_PIN;
+    ch390_conf.spi_sck_gpio = ETH_SCLK_PIN;
+    ch390_conf.spi_mosi_gpio = ETH_MOSI_PIN;
+    ch390_conf.spi_miso_gpio = ETH_MISO_PIN;
+    ch390_conf.int_gpio = ETH_INT_PIN;
+#ifdef ETH_RST_PIN
+    ch390_conf.reset_gpio = ETH_RST_PIN;
+#else
+    ch390_conf.reset_gpio = -1;
+#endif
+    ch390_conf.spi_clock_mhz = 20;
+    if ((config.network.eth_enabled) && (ETH.begin(ch390_conf))) {
+        WiFi.onEvent(WiFiEvent);
+#if !MESHTASTIC_EXCLUDE_WEBSERVER
+        createSSLCert(); // For WebServer
+#endif
+        new concurrency::Periodic("EthConnect", ethNetworkConnectedPoll);
         return true;
     }
 
@@ -234,7 +303,7 @@ bool isWifiAvailable()
 
     if (config.network.wifi_enabled && (config.network.wifi_ssid[0])) {
         return true;
-#ifdef USE_WS5500
+#if defined(USE_WS5500) || defined(USE_CH390D)
     } else if (config.network.eth_enabled) {
         return true;
 #endif
@@ -384,13 +453,13 @@ static void WiFiEvent(WiFiEvent_t event)
 #endif
         }
 #ifdef WIFI_LED
-        digitalWrite(WIFI_LED, HIGH);
+        digitalWrite(WIFI_LED, LOW ^ WIFI_STATE_ON);
 #endif
         break;
     case ARDUINO_EVENT_WIFI_STA_DISCONNECTED:
         LOG_INFO("Disconnected from WiFi access point");
 #ifdef WIFI_LED
-        digitalWrite(WIFI_LED, LOW);
+        digitalWrite(WIFI_LED, HIGH ^ WIFI_STATE_ON);
 #endif
 #if HAS_UDP_MULTICAST
         if (udpHandler) {
@@ -452,13 +521,13 @@ static void WiFiEvent(WiFiEvent_t event)
     case ARDUINO_EVENT_WIFI_AP_START:
         LOG_INFO("WiFi access point started");
 #ifdef WIFI_LED
-        digitalWrite(WIFI_LED, HIGH);
+        digitalWrite(WIFI_LED, LOW ^ WIFI_STATE_ON);
 #endif
         break;
     case ARDUINO_EVENT_WIFI_AP_STOP:
         LOG_INFO("WiFi access point stopped");
 #ifdef WIFI_LED
-        digitalWrite(WIFI_LED, LOW);
+        digitalWrite(WIFI_LED, HIGH ^ WIFI_STATE_ON);
 #endif
         break;
     case ARDUINO_EVENT_WIFI_AP_STACONNECTED:
@@ -494,18 +563,18 @@ static void WiFiEvent(WiFiEvent_t event)
         LOG_INFO("Ethernet disconnected");
         break;
     case ARDUINO_EVENT_ETH_GOT_IP:
-#ifdef USE_WS5500
+#if defined(USE_WS5500) || defined(USE_CH390D)
         LOG_INFO("Obtained IP address: %s, %u Mbps, %s", ETH.localIP().toString().c_str(), ETH.linkSpeed(),
                  ETH.fullDuplex() ? "FULL_DUPLEX" : "HALF_DUPLEX");
-        onNetworkConnected();
+        ethNetworkConnectedPending = true;
 #endif
         break;
     case ARDUINO_EVENT_ETH_GOT_IP6:
-#ifdef USE_WS5500
+#if defined(USE_WS5500) || defined(USE_CH390D)
 #if ESP_ARDUINO_VERSION >= ESP_ARDUINO_VERSION_VAL(3, 0, 0)
         LOG_INFO("Obtained Local IP6 address: %s", ETH.linkLocalIPv6().toString().c_str());
         LOG_INFO("Obtained GlobalIP6 address: %s", ETH.globalIPv6().toString().c_str());
-#else
+#elif defined(USE_WS5500)
         LOG_INFO("Obtained IP6 address: %s", ETH.localIPv6().toString().c_str());
 #endif
 #endif

src/mesh/wifi/WiFiAPClient.h

@@ -26,7 +26,7 @@ bool isWifiAvailable();
 
 uint8_t getWifiDisconnectReason();
 
-#ifdef USE_WS5500
+#if defined(USE_WS5500) || defined(USE_CH390D)
 // Startup Ethernet
 bool initEthernet();
 #endif

src/modules/AdminModule.cpp

@@ -1281,7 +1281,7 @@ void AdminModule::handleGetDeviceConnectionStatus(const meshtastic_MeshPacket &r
     }
 #endif
 
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && !defined(USE_WS5500) && !defined(USE_CH390D)
     conn.has_ethernet = true;
     conn.ethernet.has_status = true;
     if (Ethernet.linkStatus() == LinkON) {

src/modules/SystemCommandsModule.cpp

@@ -115,6 +115,17 @@ int SystemCommandsModule::handleInputEvent(const InputEvent *event)
     case INPUT_BROKER_SHUTDOWN:
         shutdownAtMsec = millis();
         return true;
+    // factory reset
+    case INPUT_BROKER_FACTORY_RST:
+        disableBluetooth();
+        LOG_INFO("Initiate full factory reset");
+        nodeDB->factoryReset(true);
+        // reboot(DEFAULT_REBOOT_SECONDS);
+        LOG_INFO("Reboot in %d seconds", DEFAULT_REBOOT_SECONDS);
+        if (screen)
+            screen->showSimpleBanner("Rebooting...", 0); // stays on screen
+        rebootAtMsec = (DEFAULT_REBOOT_SECONDS < 0) ? 0 : (millis() + DEFAULT_REBOOT_SECONDS * 1000);
+        return true;
 
     default:
         // No other input events handled here

src/mqtt/MQTT.cpp

@@ -22,6 +22,9 @@
 #if HAS_ETHERNET && defined(USE_WS5500)
 #include <ETHClass2.h>
 #define ETH ETH2
+#elif HAS_ETHERNET && defined(USE_CH390D)
+#include "ESP32_CH390.h"
+#define ETH CH390
 #endif // HAS_ETHERNET
 #include "Default.h"
 #if !defined(ARCH_NRF52) || NRF52_USE_JSON
@@ -344,6 +347,9 @@ inline bool isConnectedToNetwork()
 #ifdef USE_WS5500
     if (ETH.connected())
         return true;
+#elif defined(USE_CH390D)
+    if (ETH.isConnected())
+        return true;
 #endif
 
 #if HAS_WIFI

src/mqtt/MQTT.h

@@ -15,7 +15,7 @@
 #include <WiFiClientSecure.h>
 #endif
 #endif
-#if HAS_ETHERNET && !defined(USE_WS5500)
+#if HAS_ETHERNET && !defined(USE_WS5500) && !defined(USE_CH390D)
 #include <EthernetClient.h>
 #endif
 

src/platform/esp32/architecture.h

@@ -146,6 +146,8 @@
 #define HW_VENDOR meshtastic_HardwareModel_THINKNODE_M2
 #elif defined(ELECROW_ThinkNode_M5)
 #define HW_VENDOR meshtastic_HardwareModel_THINKNODE_M5
+#elif defined(ELECROW_ThinkNode_M7)
+#define HW_VENDOR meshtastic_HardwareModel_THINKNODE_M7
 #elif defined(ESP32_S3_PICO)
 #define HW_VENDOR meshtastic_HardwareModel_ESP32_S3_PICO
 #elif defined(SENSELORA_S3)
@@ -156,6 +158,8 @@
 #define HW_VENDOR meshtastic_HardwareModel_CHATTER_2
 #elif defined(STATION_G2)
 #define HW_VENDOR meshtastic_HardwareModel_STATION_G2
+#elif defined(STATION_G3)
+#define HW_VENDOR meshtastic_HardwareModel_STATION_G3
 #elif defined(UNPHONE)
 #define HW_VENDOR meshtastic_HardwareModel_UNPHONE
 #elif defined(WIPHONE)

src/platform/esp32/main-esp32.cpp

@@ -32,7 +32,7 @@ void variant_shutdown() {}
 #if !defined(CONFIG_IDF_TARGET_ESP32S2) && !MESHTASTIC_EXCLUDE_BLUETOOTH
 void setBluetoothEnable(bool enable)
 {
-#ifdef USE_WS5500
+#if defined(USE_WS5500) || defined(USE_CH390D)
     if ((config.bluetooth.enabled == true) && (config.network.wifi_enabled == false))
 #elif HAS_WIFI
     if (!isWifiAvailable() && config.bluetooth.enabled == true)

variants/esp32s3/ELECROW-ThinkNode-G3/pins_arduino.h

@@ -0,0 +1,26 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 17;
+static const uint8_t SCL = 18;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 39;
+static const uint8_t MOSI = 40;
+static const uint8_t MISO = 41;
+static const uint8_t SCK = 42;
+
+// #define SPI_MOSI (11)
+// #define SPI_SCK (10)
+// #define SPI_MISO (9)
+// #define SPI_CS (12)
+
+// #define SDCARD_CS SPI_CS
+
+#endif /* Pins_Arduino_h */

variants/esp32s3/ELECROW-ThinkNode-G3/platformio.ini

@@ -0,0 +1,24 @@
+[env:thinknode_g3]
+extends = esp32s3_base
+board = ESP32-S3-WROOM-1-N4
+board_build.psram_type = opi
+
+build_flags =
+  ${esp32s3_base.build_flags}
+  -D HAS_UDP_MULTICAST=1
+  -D BOARD_HAS_PSRAM
+  -D PRIVATE_HW
+  -I variants/esp32s3/ELECROW-ThinkNode-G3
+  -mfix-esp32-psram-cache-issue
+
+lib_ignore =
+  Ethernet
+
+build_src_filter =
+  ${esp32s3_base.build_src_filter}
+  +<../variants/esp32s3/ELECROW-ThinkNode-G3/*>
+
+lib_deps =
+  ${esp32s3_base.lib_deps}
+  # renovate: datasource=github-tags depName=ESP32-CH390 packageName=meshtastic/ESP32-CH390
+  https://github.com/meshtastic/ESP32-CH390/archive/refs/tags/v1.0.1.zip

variants/esp32s3/ELECROW-ThinkNode-G3/variant.cpp

@@ -0,0 +1,6 @@
+#include "mesh/NodeDB.h"
+
+void variantDefaultConfig()
+{
+    config.network.eth_enabled = true;
+}

variants/esp32s3/ELECROW-ThinkNode-G3/variant.h

@@ -0,0 +1,36 @@
+#define HAS_GPS 0
+#define HAS_WIRE 0
+#define I2C_NO_RESCAN
+
+#define WIFI_LED 5
+#define WIFI_STATE_ON 0
+
+#define LED_PIN 6
+#define LED_STATE_ON 0
+#define BUTTON_PIN 4
+
+#define LORA_SCK 42
+#define LORA_MISO 41
+#define LORA_MOSI 40
+#define LORA_CS 39
+#define LORA_RESET 21
+
+#define USE_SX1262
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 15
+#define SX126X_BUSY 47
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#define PIN_POWER_EN 45
+
+#define HAS_ETHERNET 1
+#define USE_CH390D 1
+
+#define ETH_MISO_PIN 12
+#define ETH_MOSI_PIN 11
+#define ETH_SCLK_PIN 13
+#define ETH_CS_PIN 14
+#define ETH_INT_PIN 10
+#define ETH_RST_PIN 9
+// #define ETH_ADDR 1

variants/esp32s3/ELECROW-ThinkNode-M7/pins_arduino.h

@@ -0,0 +1,19 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 17;
+static const uint8_t SCL = 18;
+
+// Default SPI is the LR1110 radio bus
+static const uint8_t SS = 12;
+static const uint8_t MOSI = 10;
+static const uint8_t MISO = 9;
+static const uint8_t SCK = 11;
+
+#endif /* Pins_Arduino_h */

variants/esp32s3/ELECROW-ThinkNode-M7/platformio.ini

@@ -0,0 +1,23 @@
+[env:thinknode_m7]
+extends = esp32s3_base
+board = ThinkNode-M7
+
+build_flags = 
+  ${esp32s3_base.build_flags}
+  -D ELECROW_ThinkNode_M7
+  -D HAS_UDP_MULTICAST=1
+  -D BOARD_HAS_PSRAM
+  -I variants/esp32s3/ELECROW-ThinkNode-M7
+  -mfix-esp32-psram-cache-issue
+
+lib_ignore = 
+  Ethernet
+
+build_src_filter =
+  ${esp32s3_base.build_src_filter}
+  +<../variants/esp32s3/ELECROW-ThinkNode-M7/*>
+
+lib_deps =
+  ${esp32s3_base.lib_deps}
+  # renovate: datasource=github-tags depName=ESP32-CH390 packageName=meshtastic/ESP32-CH390
+  https://github.com/meshtastic/ESP32-CH390/archive/refs/tags/v1.0.1.zip

variants/esp32s3/ELECROW-ThinkNode-M7/rfswitch.h

@@ -0,0 +1,11 @@
+#include "RadioLib.h"
+
+static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+    // mode                  DIO5  DIO6
+    {LR11x0::MODE_STBY, {LOW, LOW}},  {LR11x0::MODE_RX, {HIGH, LOW}},
+    {LR11x0::MODE_TX, {HIGH, HIGH}},  {LR11x0::MODE_TX_HP, {LOW, HIGH}},
+    {LR11x0::MODE_TX_HF, {LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW}},
+    {LR11x0::MODE_WIFI, {LOW, LOW}},  END_OF_MODE_TABLE,
+};

variants/esp32s3/ELECROW-ThinkNode-M7/variant.cpp

@@ -0,0 +1,6 @@
+#include "mesh/NodeDB.h"
+
+void variantDefaultConfig()
+{
+    config.network.eth_enabled = true;
+}

variants/esp32s3/ELECROW-ThinkNode-M7/variant.h

@@ -0,0 +1,43 @@
+#define HAS_GPS 0
+#define HAS_WIRE 0
+#define HAS_SCREEN 0
+#define I2C_NO_RESCAN
+
+#define UART_TX 43
+#define UART_RX 44
+
+#define WIFI_LED 3
+#define WIFI_STATE_ON 0
+
+#define LED_PIN 46
+#define LED_STATE_ON 0
+#define BUTTON_PIN 4
+#define BUTTON_ACTIVE_LOW true
+#define BUTTON_ACTIVE_PULLUP true
+
+#define LORA_SCK 11
+#define LORA_MISO 9
+#define LORA_MOSI 10
+#define LORA_CS 12
+#define LORA_RESET 39
+
+#define USE_LR1110
+#define LR1110_SPI_SCK_PIN LORA_SCK
+#define LR1110_SPI_MISO_PIN LORA_MISO
+#define LR1110_SPI_MOSI_PIN LORA_MOSI
+#define LR1110_SPI_NSS_PIN LORA_CS
+#define LR1110_IRQ_PIN 38
+#define LR1110_BUSY_PIN 13
+#define LR1110_NRESET_PIN LORA_RESET
+#define LR11X0_DIO3_TCXO_VOLTAGE 1.8
+#define LR11X0_DIO_AS_RF_SWITCH
+
+#define HAS_ETHERNET 1
+#define USE_CH390D 1
+
+#define ETH_MISO_PIN 14
+#define ETH_MOSI_PIN 48
+#define ETH_SCLK_PIN 47
+#define ETH_CS_PIN 21
+#define ETH_INT_PIN 45
+// #define ETH_ADDR 1

variants/esp32s3/station-common/station_common.h

@@ -0,0 +1,38 @@
+// Shared pin/feature defines for BQ Station G2 and G3.
+// Boards differ only in PA output power (SX126X_MAX_POWER) and the wiki URL.
+#pragma once
+
+// Station G2/G3 may not have GPS installed, but have a GROVE GPS Socket for an optional GPS module
+#define GPS_RX_PIN 7
+#define GPS_TX_PIN 15
+
+// 1.3 inch OLED Screen
+#define USE_SH1107_128_64
+
+#define I2C_SDA 5
+#define I2C_SCL 6
+
+#define BUTTON_PIN 38 // Program button
+#define BUTTON_NEED_PULLUP
+
+#define USE_SX1262
+
+#define LORA_MISO 14
+#define LORA_SCK 12
+#define LORA_MOSI 13
+#define LORA_CS 11
+
+#define LORA_RESET 21
+#define LORA_DIO1 48
+
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS // Compatibility alias; prefer LORA_CS in board definitions.
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY 47
+#define SX126X_RESET LORA_RESET
+
+// DIO2 controls an antenna switch and the TCXO voltage is controlled by DIO3
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+// NOTE: SX126X_MAX_POWER is intentionally NOT defined here — each board sets it.
+#endif

variants/esp32s3/station-g2/platformio.ini

@@ -22,10 +22,11 @@ upload_speed = 921600
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=0
-build_flags = 
+build_flags =
   ${esp32s3_base.build_flags}
   -D STATION_G2
   -I variants/esp32s3/station-g2
+  -I variants/esp32s3/station-common
   -DBOARD_HAS_PSRAM
   -DSTATION_G2
   -DARDUINO_USB_MODE=1

variants/esp32s3/station-g2/variant.h

@@ -2,39 +2,9 @@
 Board Information: https://wiki.uniteng.com/en/meshtastic/station-g2
 */
 
-// Station G2 may not have GPS installed, but it has a GROVE GPS Socket for Optional GPS Module
-#define GPS_RX_PIN 7
-#define GPS_TX_PIN 15
-
-// Station G2 has 1.3 inch OLED Screen
-#define USE_SH1107_128_64
-
-#define I2C_SDA 5 // I2C pins for this board
-#define I2C_SCL 6
-
-#define BUTTON_PIN 38 // This is the Program Button
-#define BUTTON_NEED_PULLUP
-
-#define USE_SX1262
-
-#define LORA_MISO 14
-#define LORA_SCK 12
-#define LORA_MOSI 13
-#define LORA_CS 11
-
-#define LORA_RESET 21
-#define LORA_DIO1 48
+#include "station_common.h"
 
 #ifdef USE_SX1262
-#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
-#define SX126X_DIO1 LORA_DIO1
-#define SX126X_BUSY 47
-#define SX126X_RESET LORA_RESET
-
-//  DIO2 controlls an antenna switch and the TCXO voltage is controlled by DIO3
-#define SX126X_DIO2_AS_RF_SWITCH
-#define SX126X_DIO3_TCXO_VOLTAGE 1.8
-
 // Ensure the PA does not exceed the saturation output power. More
 // Info:https://wiki.uniteng.com/en/meshtastic/station-g2#summary-for-lora-power-amplifier-conduction-test
 #define SX126X_MAX_POWER 19

variants/esp32s3/station-g3/pins_arduino.h

@@ -0,0 +1,21 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// GPIO48 Reference: https://github.com/espressif/arduino-esp32/pull/8600
+
+// The default Wire will be mapped to Screen and Sensors
+static const uint8_t SDA = 5;
+static const uint8_t SCL = 6;
+
+// Default SPI will be mapped to Radio
+static const uint8_t MISO = 14;
+static const uint8_t SCK = 12;
+static const uint8_t MOSI = 13;
+static const uint8_t SS = 11;
+
+#endif /* Pins_Arduino_h */

variants/esp32s3/station-g3/platformio.ini

@@ -0,0 +1,32 @@
+[env:station-g3]
+custom_meshtastic_hw_model = 134
+custom_meshtastic_hw_model_slug = STATION_G3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = Station G3
+custom_meshtastic_images = station-g3.svg
+custom_meshtastic_tags = B&Q
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
+extends = esp32s3_base
+board = station-g3
+board_level = pr
+board_check = true
+board_build.partitions = default_16MB.csv
+board_build.mcu = esp32s3
+upload_protocol = esptool
+;upload_port = /dev/ttyACM0
+upload_speed = 921600
+build_unflags =
+  ${esp32s3_base.build_unflags}
+  -DARDUINO_USB_MODE=0
+build_flags =
+  ${esp32s3_base.build_flags}
+  -D STATION_G3
+  -I variants/esp32s3/station-g3
+  -I variants/esp32s3/station-common
+  -DBOARD_HAS_PSRAM
+  -DSTATION_G3
+  -DARDUINO_USB_MODE=1

variants/esp32s3/station-g3/variant.h

@@ -0,0 +1,22 @@
+#include "station_common.h"
+
+#ifdef USE_SX1262
+// Station G3 reuses the same Fast-Transient DC-DC PA design as G2 (BQ35LORA900V1M).
+// PA Operating Mode is set in hardware via the PA-PL1 / PA-PL2 jumpers.
+// 19 matches the G2 cap (SX1262 19 dBm in → ~31 dBm PA out at Power Level 1, ISM compliant).
+// Raise (max 22) only if running a higher PA Power Level and you can stay within local band limits.
+#define SX126X_MAX_POWER 19
+#endif
+
+/*
+#define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
+#define ADC_MULTIPLIER 4
+#define BATTERY_SENSE_SAMPLES 15 // Set the number of samples, It has an effect of increasing sensitivity.
+#define BAT_FULLVOLT 8400
+#define BAT_EMPTYVOLT 5000
+#define BAT_CHARGINGVOLT 8400
+#define BAT_NOBATVOLT 4460
+#define CELL_TYPE_LION // same curve for liion/lipo
+#define NUM_CELLS 2
+*/