Remove incorrect LED_STATE_ON definition for t-beam-s3

Fixes #9912  and #10170

src/Power.cpp

@@ -68,7 +68,11 @@
 #define ETH ETH2
 #endif // HAS_ETHERNET
 
-#endif // MQTT
+#endif
+
+#ifndef DELAY_FOREVER
+#define DELAY_FOREVER portMAX_DELAY
+#endif
 
 #if defined(BATTERY_PIN) && defined(ARCH_ESP32)
 
@@ -90,6 +94,34 @@ static const adc_atten_t atten = ADC_ATTENUATION;
 #endif
 #endif // BATTERY_PIN && ARCH_ESP32
 
+#ifdef EXT_PWR_DETECT
+#ifndef EXT_PWR_DETECT_MODE
+#define EXT_PWR_DETECT_MODE INPUT
+// If using internal pull resistors, we can infer EXT_PWR_DETECT_VALUE
+#elif EXT_PWR_DETECT_MODE == INPUT_PULLUP
+#define EXT_PWR_DETECT_VALUE LOW
+#elif EXT_PWR_DETECT_MODE == INPUT_PULLDOWN
+#define EXT_PWR_DETECT_VALUE HIGH
+#endif
+#ifndef EXT_PWR_DETECT_VALUE
+#define EXT_PWR_DETECT_VALUE HIGH
+#endif
+#endif
+
+#ifdef EXT_CHRG_DETECT
+#ifndef EXT_CHRG_DETECT_MODE
+#define EXT_CHRG_DETECT_MODE INPUT
+// If using internal pull resistors, we can infer EXT_CHRG_DETECT_VALUE
+#elif EXT_CHRG_DETECT_MODE == INPUT_PULLUP
+#define EXT_CHRG_DETECT_VALUE LOW
+#elif EXT_CHRG_DETECT_MODE == INPUT_PULLDOWN
+#define EXT_CHRG_DETECT_VALUE HIGH
+#endif
+#ifndef EXT_CHRG_DETECT_VALUE
+#define EXT_CHRG_DETECT_VALUE HIGH
+#endif
+#endif
+
 #if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR
 #if __has_include(<Adafruit_INA219.h>)
 INA219Sensor ina219Sensor;
@@ -128,7 +160,7 @@ MAX17048Sensor max17048Sensor;
 NullSensor max17048Sensor;
 #endif
 #endif
-#endif // !MESHTASTIC_EXCLUDE_I2C
+#endif
 
 #if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR && HAS_RAKPROT
 RAK9154Sensor rak9154Sensor;
@@ -146,12 +178,46 @@ XPowersPPM *PPM = NULL;
 
 #ifdef HAS_PMU
 XPowersLibInterface *PMU = NULL;
+#else
+
+// Copy of the base class defined in axp20x.h.
+// I'd rather not include axp20x.h as it brings Wire dependency.
+class HasBatteryLevel
+{
+  public:
+    /**
+     * Battery state of charge, from 0 to 100 or -1 for unknown
+     */
+    virtual int getBatteryPercent() { return -1; }
+
+    /**
+     * The raw voltage of the battery or NAN if unknown
+     */
+    virtual uint16_t getBattVoltage() { return 0; }
+
+    /**
+     * return true if there is a battery installed in this unit
+     */
+    virtual bool isBatteryConnect() { return false; }
+
+    virtual bool isVbusIn() { return false; }
+    virtual bool isCharging() { return false; }
+};
 #endif
 
+bool pmu_irq = false;
+
 Power *power;
 
 using namespace meshtastic;
 
+// NRF52 has AREF_VOLTAGE defined in architecture.h but
+// make sure it's included. If something is wrong with NRF52
+// definition - compilation will fail on missing definition
+#if !defined(AREF_VOLTAGE) && !defined(ARCH_NRF52)
+#define AREF_VOLTAGE 3.3
+#endif
+
 /**
  * If this board has a battery level sensor, set this to a valid implementation
  */
@@ -194,7 +260,7 @@ static void battery_adcDisable()
 #endif
 }
 
-#endif // BATTERY_PIN
+#endif
 
 /**
  * A simple battery level sensor that assumes the battery voltage is attached
@@ -253,7 +319,7 @@ class AnalogBatteryLevel : public HasBatteryLevel
     }
 
     /**
-     * The raw voltage of the battery in millivolts or NAN if unknown
+     * The raw voltage of the batteryin millivolts or NAN if unknown
      */
     virtual uint16_t getBattVoltage() override
     {
@@ -270,6 +336,16 @@ class AnalogBatteryLevel : public HasBatteryLevel
         }
 #endif
 
+#ifndef ADC_MULTIPLIER
+#define ADC_MULTIPLIER 2.0
+#endif
+
+#ifndef BATTERY_SENSE_SAMPLES
+#define BATTERY_SENSE_SAMPLES                                                                                                    \
+    15 // Set the number of samples, it has an effect of increasing sensitivity in
+       // complex electromagnetic environment.
+#endif
+
 #ifdef BATTERY_PIN
         // Override variant or default ADC_MULTIPLIER if we have the override pref
         float operativeAdcMultiplier =
@@ -924,14 +1000,6 @@ int32_t Power::runOnce()
             powerFSM.trigger(EVENT_POWER_CONNECTED);
         }
 
-#ifdef PMU_POWER_BUTTON_IS_CANCEL
-        // cancel action also turns the screen on and off.
-        if (PMU->isPekeyShortPressIrq()) {
-            LOG_INFO("Input: Corona Button Click");
-            InputEvent event = {.inputEvent = (input_broker_event)INPUT_BROKER_CANCEL, .kbchar = 0, .touchX = 0, .touchY = 0};
-            inputBroker->injectInputEvent(&event);
-        }
-#endif
         /*
         Other things we could check if we cared...
 
@@ -948,6 +1016,13 @@ int32_t Power::runOnce()
             LOG_DEBUG("Battery removed");
         }
         */
+#ifndef T_WATCH_S3 // FIXME - why is this triggering on the T-Watch S3?
+        if (PMU->isPekeyLongPressIrq()) {
+            LOG_DEBUG("PEK long button press");
+            if (screen)
+                screen->setOn(false);
+        }
+#endif
 
         PMU->clearIrqStatus();
     }
@@ -1016,8 +1091,8 @@ void Power::attachPowerInterrupts()
     if (PMU) {
         attachInterrupt(
             PMU_IRQ,
-            []() {
-                power->pmu_irq = true;
+            [] {
+                pmu_irq = true;
                 power->setIntervalFromNow(0);
                 runASAP = true;
             },
@@ -1319,16 +1394,19 @@ bool Power::axpChipInit()
     uint64_t pmuIrqMask = 0;
 
     if (PMU->getChipModel() == XPOWERS_AXP192) {
-        pmuIrqMask = XPOWERS_AXP192_VBUS_INSERT_IRQ | XPOWERS_AXP192_VBUS_REMOVE_IRQ | XPOWERS_AXP192_PKEY_SHORT_IRQ;
+        pmuIrqMask = XPOWERS_AXP192_VBUS_INSERT_IRQ | XPOWERS_AXP192_BAT_INSERT_IRQ | XPOWERS_AXP192_PKEY_SHORT_IRQ;
     } else if (PMU->getChipModel() == XPOWERS_AXP2101) {
-        pmuIrqMask = XPOWERS_AXP2101_VBUS_INSERT_IRQ | XPOWERS_AXP2101_VBUS_REMOVE_IRQ | XPOWERS_AXP2101_PKEY_SHORT_IRQ;
+        pmuIrqMask = XPOWERS_AXP2101_VBUS_INSERT_IRQ | XPOWERS_AXP2101_BAT_INSERT_IRQ | XPOWERS_AXP2101_PKEY_SHORT_IRQ;
     }
 
     pinMode(PMU_IRQ, INPUT);
 
-    // We wake on IRQ, so only enable the IRQs that we care about.
-    // we want USB plug and unplug to update the screen and LED status,
-    // and short press on the power button to trigger the "cancel" action in the UI (which also turns the screen on and off).
+    // we do not look for AXPXXX_CHARGING_FINISHED_IRQ & AXPXXX_CHARGING_IRQ
+    // because it occurs repeatedly while there is no battery also it could cause
+    // inadvertent waking from light sleep just because the battery filled we
+    // don't look for AXPXXX_BATT_REMOVED_IRQ because it occurs repeatedly while
+    // no battery installed we don't look at AXPXXX_VBUS_REMOVED_IRQ because we
+    // don't have anything hooked to vbus
     PMU->enableIRQ(pmuIrqMask);
 
     PMU->clearIrqStatus();
@@ -1636,7 +1714,7 @@ bool Power::lipoChargerInit()
     return true;
 }
 
-#else  // HAS_PPM
+#else
 /**
  * The Lipo battery level sensor is unavailable - default to AnalogBatteryLevel
  */
@@ -1644,7 +1722,7 @@ bool Power::lipoChargerInit()
 {
     return false;
 }
-#endif // HAS_PPM
+#endif
 
 #ifdef HELTEC_MESH_SOLAR
 #include "meshSolarApp.h"
@@ -1706,7 +1784,7 @@ bool Power::meshSolarInit()
     return true;
 }
 
-#else  // HELTEC_MESH_SOLAR
+#else
 /**
  * The meshSolar battery level sensor is unavailable - default to
  * AnalogBatteryLevel
@@ -1715,7 +1793,7 @@ bool Power::meshSolarInit()
 {
     return false;
 }
-#endif // HELTEC_MESH_SOLAR
+#endif
 
 #ifdef HAS_SERIAL_BATTERY_LEVEL
 #include <SoftwareSerial.h>
@@ -1723,7 +1801,7 @@ bool Power::meshSolarInit()
 /**
  * SerialBatteryLevel class for pulling battery information from a secondary MCU over serial.
  */
-class SerialBatteryLevel : public AnalogBatteryLevel
+class SerialBatteryLevel : public HasBatteryLevel
 {
 
   public:
@@ -1800,6 +1878,16 @@ class SerialBatteryLevel : public AnalogBatteryLevel
         return false;
     }
 
+    virtual bool isCharging() override
+    {
+#ifdef EXT_CHRG_DETECT
+        return digitalRead(EXT_CHRG_DETECT) == EXT_CHRG_DETECT_VALUE;
+
+#endif
+        // by default, we check the battery voltage only
+        return isVbusIn();
+    }
+
   private:
     SoftwareSerial BatterySerial = SoftwareSerial(SERIAL_BATTERY_RX, SERIAL_BATTERY_TX);
     uint8_t Data[6] = {0};
@@ -1829,7 +1917,7 @@ bool Power::serialBatteryInit()
     return true;
 }
 
-#else  // HAS_SERIAL_BATTERY_LEVEL
+#else
 /**
  * If this device has no serial battery level sensor, don't try to use it.
  */
@@ -1837,4 +1925,4 @@ bool Power::serialBatteryInit()
 {
     return false;
 }
-#endif // HAS_SERIAL_BATTERY_LEVEL
+#endif

src/detect/ScanI2CTwoWire.cpp

@@ -415,45 +415,30 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
 #if !defined(M5STACK_UNITC6L)
             case INA_ADDR: // Same as SHT2X
             case INA_ADDR_ALTERNATE:
-            case INA_ADDR_WAVESHARE_UPS: {
-                uint16_t mfg = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFE), 2);
+            case INA_ADDR_WAVESHARE_UPS:
+                registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFE), 2);
+                LOG_DEBUG("Register MFG_UID: 0x%x", registerValue);
+                if (registerValue == 0x5449) {
+                    registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFF), 2);
+                    LOG_DEBUG("Register DIE_UID: 0x%x", registerValue);
 
-                LOG_DEBUG("Register MFG_UID: 0x%x", mfg);
-
-                // Only read DIE_UID for vendors we recognize as INA-compatible to avoid
-                // an extra I2C transaction + delay on other devices sharing this address.
-                if (mfg == 0x5449 || mfg == 0x190F) {
-                    uint16_t die = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFF), 2);
-                    LOG_DEBUG("Register DIE_UID: 0x%x", die);
-
-                    // TI INA226 or fully compatible clones (e.g. TPA626)
-                    if (mfg == 0x5449 && die == 0x2260) {
+                    if (registerValue == 0x2260) {
                         logFoundDevice("INA226", (uint8_t)addr.address);
                         type = INA226;
-                    }
-                    // Silergy SQ52201 (INA226-compatible with different IDs)
-                    else if (mfg == 0x190F && die == 0x0000) {
-                        logFoundDevice("INA226 (SQ52201)", (uint8_t)addr.address);
-                        type = INA226;
-                    }
-                    // TI INA260
-                    else if (mfg == 0x5449) {
+                    } else {
                         logFoundDevice("INA260", (uint8_t)addr.address);
                         type = INA260;
                     }
-                }
 #if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR
-                if (type == NONE && detectSHT21SerialNumber(i2cBus, (uint8_t)addr.address)) {
+                } else if (detectSHT21SerialNumber(i2cBus, (uint8_t)addr.address)) {
                     logFoundDevice("SHTXX (SHT2X)", (uint8_t)addr.address);
                     type = SHTXX;
-                }
 #endif
-                else { // Assume INA219 if none of the above ones are found
+                } else { // Assume INA219 if none of the above ones are found
                     logFoundDevice("INA219", (uint8_t)addr.address);
                     type = INA219;
                 }
                 break;
-            }
             case INA3221_ADDR:
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFE), 2);
                 LOG_DEBUG("Register MFG_UID FE: 0x%x", registerValue);

src/power.h

@@ -28,54 +28,6 @@
 #define NUM_CELLS 1
 #endif
 
-// Set the number of samples, it has an effect of increasing sensitivity in complex electromagnetic environment.
-#ifndef BATTERY_SENSE_SAMPLES
-#define BATTERY_SENSE_SAMPLES 15
-#endif
-
-#ifndef ADC_MULTIPLIER
-#define ADC_MULTIPLIER 2.0
-#endif
-
-#ifdef EXT_PWR_DETECT
-#ifndef EXT_PWR_DETECT_MODE
-#define EXT_PWR_DETECT_MODE INPUT
-// If using internal pull resistors, we can infer EXT_PWR_DETECT_VALUE
-#elif EXT_PWR_DETECT_MODE == INPUT_PULLUP
-#define EXT_PWR_DETECT_VALUE LOW
-#elif EXT_PWR_DETECT_MODE == INPUT_PULLDOWN
-#define EXT_PWR_DETECT_VALUE HIGH
-#endif
-#ifndef EXT_PWR_DETECT_VALUE
-#define EXT_PWR_DETECT_VALUE HIGH
-#endif
-#endif
-
-#ifdef EXT_CHRG_DETECT
-#ifndef EXT_CHRG_DETECT_MODE
-#define EXT_CHRG_DETECT_MODE INPUT
-// If using internal pull resistors, we can infer EXT_CHRG_DETECT_VALUE
-#elif EXT_CHRG_DETECT_MODE == INPUT_PULLUP
-#define EXT_CHRG_DETECT_VALUE LOW
-#elif EXT_CHRG_DETECT_MODE == INPUT_PULLDOWN
-#define EXT_CHRG_DETECT_VALUE HIGH
-#endif
-#ifndef EXT_CHRG_DETECT_VALUE
-#define EXT_CHRG_DETECT_VALUE HIGH
-#endif
-#endif
-
-#ifndef DELAY_FOREVER
-#define DELAY_FOREVER portMAX_DELAY
-#endif
-
-// NRF52 has AREF_VOLTAGE defined in architecture.h but
-// make sure it's included. If something is wrong with NRF52
-// definition - compilation will fail on missing definition
-#if !defined(AREF_VOLTAGE) && !defined(ARCH_NRF52)
-#define AREF_VOLTAGE 3.3
-#endif
-
 #ifdef BAT_MEASURE_ADC_UNIT
 extern RTC_NOINIT_ATTR uint64_t RTC_reg_b;
 #include "soc/sens_reg.h" // needed for adc pin reset
@@ -134,31 +86,6 @@ extern RAK9154Sensor rak9154Sensor;
 extern XPowersLibInterface *PMU;
 #endif
 
-#ifndef HAS_PMU
-// Copy of the base class defined in axp20x.h, to prevent an automatic wire.h dependency
-class HasBatteryLevel
-{
-  public:
-    /**
-     * Battery state of charge, from 0 to 100 or -1 for unknown
-     */
-    virtual int getBatteryPercent() { return -1; }
-
-    /**
-     * The raw voltage of the battery or NAN if unknown
-     */
-    virtual uint16_t getBattVoltage() { return 0; }
-
-    /**
-     * return true if there is a battery installed in this unit
-     */
-    virtual bool isBatteryConnect() { return false; }
-
-    virtual bool isVbusIn() { return false; }
-    virtual bool isCharging() { return false; }
-};
-#endif
-
 class Power : public concurrency::OSThread
 {
 
@@ -183,8 +110,6 @@ class Power : public concurrency::OSThread
     void attachPowerInterrupts();
     void detachPowerInterrupts();
 
-    volatile bool pmu_irq = false;
-
   protected:
     meshtastic::PowerStatus *statusHandler;
 

variants/esp32s3/t-watch-s3/variant.h

@@ -42,7 +42,6 @@
 #define DAC_I2S_MCLK -1
 
 #define HAS_AXP2101
-#define PMU_POWER_BUTTON_IS_CANCEL // maps a short click of the power button to a cancel action (turning off the screen)
 
 // PCF8563 RTC Module
 #define PCF8563_RTC 0x51
@@ -61,8 +60,6 @@
 
 #define BUTTON_PIN 0 // only for Plus version
 
-#define PMU_IRQ 21 // Interrupt pin for the PMU
-
 #define USE_SX1262
 #define USE_SX1268
 

variants/esp32s3/tbeam-s3-core/variant.h

@@ -46,9 +46,9 @@
 #define LR11X0_DIO_AS_RF_SWITCH
 #endif
 
-// Voiding warrenties, we're gonna try the IRQ
-#define PMU_IRQ 40
-#define PMU_POWER_BUTTON_IS_CANCEL // maps a short click of the power button to a cancel action (turning off the screen)
+// Leave undefined to disable our PMU IRQ handler.  DO NOT ENABLE THIS because the pmuirq can cause sperious interrupts
+// and waking from light sleep
+// #define PMU_IRQ 40
 #define HAS_AXP2101
 
 // PCF8563 RTC Module