MQTT password was logged in cleartext via LOG_INFO when connecting to
the broker, exposing credentials to anyone with log access. Replace
the password format specifier with a static mask.
Co-authored-by: Patrickschell609 <patrickschell609@users.noreply.github.com>
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
* Consolidate SHTs into one class
* Remove separate SHT imports
* Create one single SHTXX sensor type
* Let the SHTXXSensor class handle variant detection
* Minor logging improvements
* Add functions to set accuracy on SHT3X and SHT4X
* Fix variable init in constructor
* Add bus to SHT sensor init
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix accuracy conditions on SHTXX
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Merge upstream
* Add SHT2X detection on 0x40
* Read second part of SHT2X serial number
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
SerialModule's weather station parser divides by velCount and dirCount
to compute wind speed/direction averages. Both counters are only
incremented when their respective sensor readings arrive, but the
division runs whenever gotwind is true (set by EITHER reading) and
the averaging interval has elapsed.
If only WindDir arrives without WindSpeed (or vice versa), or if the
timer fires before any readings accumulate, the division produces
undefined behavior (floating-point divide by zero on embedded = NaN
or hardware fault depending on platform).
Fix: add velCount > 0 && dirCount > 0 guard to the averaging block.
Co-authored-by: Patrickschell609 <patrickschell609@users.noreply.github.com>
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix MESHTASTIC_EXCLUDE_SCREEN
* mesh-tab map constraints (2 MB PSRAM)
* point MUI commit to the related PR
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Improved flow to make easier
The emojis are intentional! I had minimal LLM input!!!
* try and fix input variable sanitisation
* and again
* again
* Copilot fixed it for me
* copilot didn't fix it for me
* copilot might have fixed it and I broke it by copypasting
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix TAG low‑voltage reboot hang after App configuration
* nRF52: Move low-VDD System OFF logic to variant hook
* Addressed review
* serialize SAADC access with shared mutex for VDD and battery reads
* raise LPCOMP wake threshold to ensure rising-edge wake
* Trunk fmt
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(routing): prevent licensed users from rebroadcasting packets from unlicensed or unknown users
* fix(routing): prevent licensed users from rebroadcasting packets to or from unlicensed users
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The W5100S Ethernet chip has only 4 hardware sockets. On RAK4631
Ethernet gateways with syslog and NTP enabled, all 4 sockets were
permanently consumed (NTP UDP + Syslog UDP + TCP API listener + TCP
API client), leaving none for MQTT, DHCP lease renewal, or additional
TCP connections.
- NTP: Remove permanent timeClient.begin() at startup; NTPClient::update()
auto-initializes when needed. Add timeClient.end() after each query to
release the UDP socket immediately.
- Syslog: Remove socket allocation from Syslog::enable(). Open and close
the UDP socket on-demand in _sendLog() around each message send.
- MQTT: Fix socket leak in isValidConfig() where a successful test
connection was never closed (PubSubClient destructor does not call
disconnect). Add explicit pubSub->disconnect() before returning.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The W5100S Ethernet chip has only 4 hardware sockets. On RAK4631
Ethernet gateways with syslog and NTP enabled, all 4 sockets were
permanently consumed (NTP UDP + Syslog UDP + TCP API listener + TCP
API client), leaving none for MQTT, DHCP lease renewal, or additional
TCP connections.
- NTP: Remove permanent timeClient.begin() at startup; NTPClient::update()
auto-initializes when needed. Add timeClient.end() after each query to
release the UDP socket immediately.
- Syslog: Remove socket allocation from Syslog::enable(). Open and close
the UDP socket on-demand in _sendLog() around each message send.
- MQTT: Fix socket leak in isValidConfig() where a successful test
connection was never closed (PubSubClient destructor does not call
disconnect). Add explicit pubSub->disconnect() before returning.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
PlatformIO registry is (probably) rate limiting us. Mitigate by switching to GitHub source zips (based upon tags).
This change does not include any updates, simply swapping to a new download location.
* Fix TransmitHistory to improve epoch handling
* Enable epoch handling in unit tests
* Improve comments and test handling for epoch persistence in TransmitHistory
* Add boot-relative timestamp handling and unit tests for TransmitHistory
* loadFromDisk should handle legacy entries and clean up old v1 files after migration
* Revert "loadFromDisk should handle legacy entries and clean up old v1 files after migration"
This reverts commit eb7e5c7acfa4ac077fe50980be752e4b42a739b8.
* Add NodeInfoModule integration for RTC quality changes and trigger immediate checks
* Update test conditions for RTC quality checks
* Fix TAG low‑voltage reboot hang after App configuration
* nRF52: Move low-VDD System OFF logic to variant hook
* Addressed review
* serialize SAADC access with shared mutex for VDD and battery reads
* raise LPCOMP wake threshold to ensure rising-edge wake
* Trunk fmt
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
We cache and dedupe our dependencies, referring to them with multiple methods/urls is just noise.
```
lewisxhe/XPowersLib@0.3.3
lewisxhe/SensorLib@0.3.4
```
This does *not* include any updates, just a cleanup.
* fix(routing): prevent licensed users from rebroadcasting packets from unlicensed or unknown users
* fix(routing): prevent licensed users from rebroadcasting packets to or from unlicensed users
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix: apply all LoRa config changes live without rebooting
All LoRa radio settings (SF, BW, CR, frequency, power, preset,
sx126x_rx_boosted_gain) now apply immediately via reconfigure()
without requiring a node reboot.
- AdminModule: requiresReboot = false for all LoRa config changes;
LoRa changes were already handled by the configChanged observer
calling reconfigure() but the reboot flag was set unnecessarily
- AdminModule: validate LORA_24 region against radio hardware at
config time; reject with BAD_REQUEST if hardware lacks 2.4 GHz
capability (wideLora() returns false or no radio instance)
- SX126xInterface/LR11x0Interface: apply sx126x_rx_boosted_gain in
reconfigure(); register 0x08AC is writable in STDBY mode (SX1261/2
datasheet §9.6); retention registers written so setting survives
warm-sleep cycles; log warning on setter failure
- DebugRenderer: show BW/SF/CR on debug screen when custom modem is
active instead of the preset name
- DisplayFormatters: clarify comment on getModemPresetDisplayName
* fix: remove redundant reboot after LoRa config changes in on-device menus
Region, frequency slot, and radio preset pickers in MenuHandler all
called reloadConfig() then immediately set rebootAtMsec. reloadConfig()
already fires the configChanged observer which calls reconfigure(), so
the forced reboot was unnecessary — same rationale as the parent commit.
* fix: guard LORA_24 region selection against hardware capability in on-device menu
Without a reboot, reconfigure() now applies region changes directly.
Previously getRadio() caught the LORA_24-on-sub-GHz mismatch post-reboot
and reverted to UNSET — that safety net is gone. Add an explicit wideLora()
check in LoraRegionPicker so sub-GHz-only hardware silently ignores LORA_24
selection instead of attempting a live reconfigure with an invalid frequency.
---------
Co-authored-by: elwimen <elwimen@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The touch-to-backlight feature was gated behind TTGO_T_ECHO_PLUS, but
the regular T-Echo has the same backlight pin (PIN_EINK_EN, P1.11).
This changes the guard to use PIN_EINK_EN only, so any device with an
e-ink backlight pin gets the feature.
Fixes#7630
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix issue 9792, decode packet for TR test
* Fix 9792: Assure packet id decoded for TR test
* Potential fix for pull request finding
Log improvement for failure to decode packet.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* trunk fmt
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* fix: MQTT settings silently fail to persist when broker is unreachable
isValidConfig() was testing broker connectivity via connectPubSub() as
part of config validation. When the broker was unreachable (network not
ready, DNS failure, server down), the function returned false, causing
AdminModule to skip saving settings entirely — silently.
This removes the connectivity test from isValidConfig(), which now only
validates configuration correctness (TLS support, default server port).
Connectivity is handled by the MQTT module's existing reconnect loop.
Fixes#9107
* Add client warning notification when MQTT broker is unreachable
Per maintainer feedback: instead of silently saving when the broker
can't be reached, send a WARNING notification to the client saying
"MQTT settings saved, but could not reach the MQTT server."
Settings still always persist regardless of connectivity — the core
fix from the previous commit is preserved. The notification is purely
advisory so users know to double-check their server address and
credentials if the connection test fails.
When the network is not available at all, the connectivity check is
skipped entirely with a log message.
* Address Copilot review feedback
- Fix warning message wording: "Settings will be saved" instead of
"Settings saved" (notification fires before AdminModule persists)
- Add null check on clientNotificationPool.allocZeroed() to prevent
crash if pool is exhausted (matches AdminModule::sendWarning pattern)
- Fix test comments to accurately describe conditional connectivity
check behavior and IS_RUNNING_TESTS compile-out
* Remove connectivity check from isValidConfig entirely
Reverts the advisory connectivity check added in the previous commit.
While the intent was to warn users about unreachable brokers,
connectPubSub() mutates the isConnected state of the running MQTT
module and performs synchronous network operations that can block
the config-save path.
The cleanest approach: isValidConfig() validates config correctness
only (TLS support, default server port). The MQTT reconnect loop
handles connectivity after settings are persisted and the device
reboots. If the broker is unreachable, the user will see it in the
MQTT connection status — no special notification needed.
This returns to the simpler design from the first commit, which was
tested on hardware and confirmed working.
* Use lightweight TCP check instead of connectPubSub for validation
Per maintainer feedback: users need connectivity feedback, but
connectPubSub() mutates the module's isConnected state.
This uses a standalone MQTTClient TCP connection test that:
- Checks if the server IP/port is reachable
- Sends a WARNING notification if unreachable
- Does NOT establish an MQTT session or mutate any module state
- Does NOT block saving — isValidConfig always returns true
The TCP test client is created locally, used, and destroyed within
the function scope. No side effects on the running MQTT module.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The touch-to-backlight feature was gated behind TTGO_T_ECHO_PLUS, but
the regular T-Echo has the same backlight pin (PIN_EINK_EN, P1.11).
This changes the guard to use PIN_EINK_EN only, so any device with an
e-ink backlight pin gets the feature.
Fixes#7630
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix issue 9792, decode packet for TR test
* Fix 9792: Assure packet id decoded for TR test
* Potential fix for pull request finding
Log improvement for failure to decode packet.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* trunk fmt
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Enhance LoRa configuration with modem presets and validation logic
* Rename bootstrapLoRaConfigFromPreset tests to validateModemConfig for clarity and consistency
* additional tidy-ups to the validateModemConfig - still fundamentally broken at this point
* Enhance region validation by adding numPresets to RegionInfo and implementing validateRegionConfig in RadioInterface
* Add validation for modem configuration in applyModemConfig
* Fix region unset handling and improve modem config validation in handleSetConfig
* Refactor LoRa configuration validation methods and introduce clamping method for invalid settings
* Update handleSetConfig to use fromOthers parameter to either correct or reject invalid settings
* Fix some of the copilot review comments for LoRa configuration validation and clamping methods; add tests for region and preset handling
* Redid the slot default checking and calculation. Should resolve the outstanding comments.
* Add bandwidth calculation for LoRa modem preset fallback in clampConfigLora
* Remove unused preset name variable in validateConfigLora and fix default frequency slot check in applyModemConfig
* update tests for region handling
* Got the synthetic colleague to add mock service for testing
* Flash savings... hopefully
* Refactor modem preset handling to use sentinel values and improve default preset retrieval
* Refactor region handling to use profile structures for modem presets and channel calculations
* added comments for clarity on parameters
* Add shadow table tests and validateConfigLora enhancements for region presets
* Add isFromUs tests for preset validation in AdminModule
* Respond to copilot github review
* address copilot comments
* address null poointers
* fix build errors
* Fix the fix, undo the silly suggestions from synthetic reviewer.
* we all float here
* Fix include path for AdminModule in test_main.cpp
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* More suggestion fixes
* admin module merge conflicts
* admin module fixes from merge hell
* fix: initialize default frequency slot and custom channel name; update LNA mode handling
* save some bytes...
* fix: simplify error logging for bandwidth checks in LoRa configuration
* Update src/mesh/MeshRadio.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* fix: MQTT settings silently fail to persist when broker is unreachable
isValidConfig() was testing broker connectivity via connectPubSub() as
part of config validation. When the broker was unreachable (network not
ready, DNS failure, server down), the function returned false, causing
AdminModule to skip saving settings entirely — silently.
This removes the connectivity test from isValidConfig(), which now only
validates configuration correctness (TLS support, default server port).
Connectivity is handled by the MQTT module's existing reconnect loop.
Fixes#9107
* Add client warning notification when MQTT broker is unreachable
Per maintainer feedback: instead of silently saving when the broker
can't be reached, send a WARNING notification to the client saying
"MQTT settings saved, but could not reach the MQTT server."
Settings still always persist regardless of connectivity — the core
fix from the previous commit is preserved. The notification is purely
advisory so users know to double-check their server address and
credentials if the connection test fails.
When the network is not available at all, the connectivity check is
skipped entirely with a log message.
* Address Copilot review feedback
- Fix warning message wording: "Settings will be saved" instead of
"Settings saved" (notification fires before AdminModule persists)
- Add null check on clientNotificationPool.allocZeroed() to prevent
crash if pool is exhausted (matches AdminModule::sendWarning pattern)
- Fix test comments to accurately describe conditional connectivity
check behavior and IS_RUNNING_TESTS compile-out
* Remove connectivity check from isValidConfig entirely
Reverts the advisory connectivity check added in the previous commit.
While the intent was to warn users about unreachable brokers,
connectPubSub() mutates the isConnected state of the running MQTT
module and performs synchronous network operations that can block
the config-save path.
The cleanest approach: isValidConfig() validates config correctness
only (TLS support, default server port). The MQTT reconnect loop
handles connectivity after settings are persisted and the device
reboots. If the broker is unreachable, the user will see it in the
MQTT connection status — no special notification needed.
This returns to the simpler design from the first commit, which was
tested on hardware and confirmed working.
* Use lightweight TCP check instead of connectPubSub for validation
Per maintainer feedback: users need connectivity feedback, but
connectPubSub() mutates the module's isConnected state.
This uses a standalone MQTTClient TCP connection test that:
- Checks if the server IP/port is reachable
- Sends a WARNING notification if unreachable
- Does NOT establish an MQTT session or mutate any module state
- Does NOT block saving — isValidConfig always returns true
The TCP test client is created locally, used, and destroyed within
the function scope. No side effects on the running MQTT module.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix for preserving pki_encrypted and public_key when relaying UDP multicast packets to radio.
PKI DMs sent over UDP multicast had their pki_encrypted flag and public_key fields explicitly cleared before being forwarded to the LoRa radio. This caused the receiving node to treat the packet as a channel-encrypted message it couldn't decrypt, silently dropping it.
The MQTT ingress path correctly preserves these fields. The UDP multicast ingress path should behave the same way.
* Zeroize MeshPacket before decoding
Zeroize MeshPacket before decoding to prevent data leakage.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix for preserving pki_encrypted and public_key when relaying UDP multicast packets to radio.
PKI DMs sent over UDP multicast had their pki_encrypted flag and public_key fields explicitly cleared before being forwarded to the LoRa radio. This caused the receiving node to treat the packet as a channel-encrypted message it couldn't decrypt, silently dropping it.
The MQTT ingress path correctly preserves these fields. The UDP multicast ingress path should behave the same way.
* Zeroize MeshPacket before decoding
Zeroize MeshPacket before decoding to prevent data leakage.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout
PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.
Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
in reconnectETH(); on mismatch, perform full hardware reset and
re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
consume limited W5100S hardware sockets
Fixesmeshtastic/firmware#6970
Made-with: Cursor
* Log actual elapsed idle time instead of constant timeout value
Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.
Made-with: Cursor
* Update src/mesh/api/ServerAPI.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Stop UDP multicast handler during W5100S brownout recovery
After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.
Made-with: Cursor
* Address Copilot review: recovery flags and timeout constant
Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.
Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.
Made-with: Cursor
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout
PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.
Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
in reconnectETH(); on mismatch, perform full hardware reset and
re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
consume limited W5100S hardware sockets
Fixesmeshtastic/firmware#6970
Made-with: Cursor
* Log actual elapsed idle time instead of constant timeout value
Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.
Made-with: Cursor
* Update src/mesh/api/ServerAPI.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Stop UDP multicast handler during W5100S brownout recovery
After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.
Made-with: Cursor
* Address Copilot review: recovery flags and timeout constant
Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.
Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.
Made-with: Cursor
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix NodeInfo suppression logic to ensure suppression only applies to external requests
* Ensure NodeInfo reply suppression logic to only apply for external requests which are actually nodeinfo packets
Problem:
- Inserting a µSD card causes RadioLib to hit a critical error and reboot
- Device enters a boot loop as the SD card remains inserted
Reproduction:
- Insert a µSD card and power on
- RadioLib reports a critical error on boot
- Device reboots, repeating indefinitely
Root cause:
- On T-Lora Pager, SX1262 and the µSD slot share the same physical SPI bus
(same SCK/MOSI/MISO pins, differentiated only by CS)
- SDCARD_USE_SPI1 is intended for boards where SD is on a separate SPI bus;
it initializes a second ESP32 SPI peripheral (SPI3) for SD
- SPI2 is already driving those same pins for LoRa, so both controllers
simultaneously drive the same GPIO lines, causing bus contention
Fix:
- Remove SDCARD_USE_SPI1 so both devices share a single SPI peripheral (SPI2),
with CS pins providing device selection as intended
- Tested on a custom fork of device-ui; LoRa and SD card map tiles both work
correctly with an SD card inserted
Signed-off-by: Andrew Yong <me@ndoo.sg>
Problem:
- Inserting a µSD card causes RadioLib to hit a critical error and reboot
- Device enters a boot loop as the SD card remains inserted
Reproduction:
- Insert a µSD card and power on
- RadioLib reports a critical error on boot
- Device reboots, repeating indefinitely
Root cause:
- On T-Lora Pager, SX1262 and the µSD slot share the same physical SPI bus
(same SCK/MOSI/MISO pins, differentiated only by CS)
- SDCARD_USE_SPI1 is intended for boards where SD is on a separate SPI bus;
it initializes a second ESP32 SPI peripheral (SPI3) for SD
- SPI2 is already driving those same pins for LoRa, so both controllers
simultaneously drive the same GPIO lines, causing bus contention
Fix:
- Remove SDCARD_USE_SPI1 so both devices share a single SPI peripheral (SPI2),
with CS pins providing device selection as intended
- Tested on a custom fork of device-ui; LoRa and SD card map tiles both work
correctly with an SD card inserted
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Enable pre-hop drop handling by default
* Remove early break if BME/DPS sensors are not detected at the BME address
* revert sneaky change
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Enable pre-hop drop handling by default
* Remove early break if BME/DPS sensors are not detected at the BME address
* revert sneaky change
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The Seeed Xiao S3 Kit's default GPS is an L76K which operates at 9600 baud, so when this variant was defined that baud rate was specified.
However, this is a development board and it is expected that users can attach their own devices. This includes GPS, which may operate at a different baud rate. The current fixed baud rate prevents this, so this patch removes that setting.
This will revert to the regular automatic probe method. This will successfully detect the L76K as before (the same speed as before since 9600 baud is the first baud rate checked), but also allow other GPSes at other baud rates to be detected.
Thanks to @ScarpMarc for the report
Fixes https://github.com/meshtastic/firmware/issues/9373#issuecomment-3774802763
* Deprecate forwarding for invalid hop_start
* Add pre-hop packet drop policy
* Log ignored rebroadcasts for pre-hop packets
* Respect pre-hop policy ALLOW in routing gates
* Exempt local packets from pre-hop drop policy
* Format pre-hop log line
* Add MODERN_ONLY rebroadcast mode for pre-hop packets
* Simplify implementation for drop packet only behaviour
* Revert formatting-only changes
* Match ReliableRouter EOF formatting
* Make pre-hop drop a build-time flag
* Rework to compile/build flag MESHTASTIC_PREHOP_DROP
* Set MESHTASTIC_PREHOP_DROP off by default
* Inline pre-hop hop_start validity check
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jord <650645+DivineOmega@users.noreply.github.com>
The Seeed Xiao S3 Kit's default GPS is an L76K which operates at 9600 baud, so when this variant was defined that baud rate was specified.
However, this is a development board and it is expected that users can attach their own devices. This includes GPS, which may operate at a different baud rate. The current fixed baud rate prevents this, so this patch removes that setting.
This will revert to the regular automatic probe method. This will successfully detect the L76K as before (the same speed as before since 9600 baud is the first baud rate checked), but also allow other GPSes at other baud rates to be detected.
Thanks to @ScarpMarc for the report
Fixes https://github.com/meshtastic/firmware/issues/9373#issuecomment-3774802763
Fixes this build error:
<command-line>: error: expected unqualified-id before '-' token
/home/<snip>/.platformio/packages/framework-arduinoespressif32/variants/esp32s3/pins_arduino.h:15:22: note: in expansion of macro 'LED_BUILTIN'
15 | static const uint8_t LED_BUILTIN = SOC_GPIO_PIN_COUNT + PIN_RGB_LED;
| ^~~~~~~~~~~
More info: https://github.com/meshtastic/firmware/pull/9122#issuecomment-4028263894
The fix is consistent with variants/esp32s3/heltec_v3/platformio.ini
This commit is intentionally on the develop branch, because it's harmless to
develop branch, and makes us more ready for pioarduino when the time comes.
Heltec v4 introduced in: https://github.com/meshtastic/firmware/pull/7845
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add C++17 support
* Add C++17 runtime probes and update build configurations for STM32 and Portduino
* Remove unflags
* Update C++ standard flags across the platforms
* Convert a couple of instances to structured bindings
* NRF52 platform.txt to add C++17 support
* Still need the unflags apparently
* Remove C++17 runtime probe tests from test_main.cpp
* Reconfigured doesnt need a nodiscard
* Remove nodiscard attribute from init() method in RadioInterface
* Remove mbedtls/error.h from build flags
Removed include directive for mbedtls/error.h from build flags.
* Fix IRAM overflow
* Fix IRAM overflow
* Add build flag to exclude MQTT from rak11200
* Update C++ standard from gnu17 to gnu++17
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Addition of traffic management module
* Fixing compile issues, but may still need to update protobufs.
* Fixing log2Floor in cuckoo hash function
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Adding station-g2 and portduino varients to be able to use this module.
* Spoofing from address for nodeinfo cache
* Changing name and behavior for zero_hop_telemetry / zero_hop_position
* Name change for exhausting telemetry packets and setting hop_limit to 1 so it will be 0 when sent.
* Updated hop logic, including exhaustRequested flag to bypass some checks later in the code.
* Reducing memory on nrf52 nodes further to 12 bytes per entry, 12KB total using 8 bit hashes with 0.4% collision. Probably ok. Adding portduino to the platforms that don't need to worry about memory as much.
* Fixing hopsAway for nodeinfo responses.
* traffic_management.nodeinfo_direct_response_min_hops -> traffic_management.nodeinfo_direct_response_max_hops
* Removing dry run mode
* Updates to UnifiedCacheEntry to use a common cache, created defaults for some values, reduced a couple bytes per entry by using a resolution-scale time selection based on configuration value.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Creating consistent log messages
* Remove docs/ESP32_Power_Management.md from traffic_module
* Add unit tests for Traffic Management Module functionality
* Fixing compile issues, but may still need to update protobufs.
* Adding support for traffic management in PhoneAPI.
* Making router_preserve_hops work without checking if the previous hop was a router. Also works for CLIENT_BASE.
* Enhance traffic management logging and configuration. Updated log messages in NextHopRouter and Router to include more context. Adjusted traffic management configuration checks in AdminModule and improved cache handling in TrafficManagementModule. Ensured consistent enabling of traffic management across various variants.
* Implement destructor for TrafficManagementModule and improve cache allocation handling. The destructor ensures proper deallocation of cache memory based on its allocation source (PSRAM or heap). Additionally, updated cache allocation logic to log warnings only when PSRAM allocation fails.
* Update TrafficManagementModule with enhanced comments for clarity and improve cache handling logic. Update protobuf submodule to latest commit.
* Add mock classes and unit tests for Traffic Management Module functionality.
* Refactor setup and loop functions in test_main.cpp to include extern "C" linkage
* Update comment to include reduced memory requirements
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Re-arranging comments for programmers with the attention span of less than 5 lines of code.
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update comments in TrafficManagementModule to reflect changes in timestamp epoch handling and memory optimization details.
* bug: Use node-wide config_ok_to_mqtt setting for cached NodeInfo replies.
* Better way to handle clearing the ok_to_mqtt bit
* Add bucketing to cuckoo hashing, allowing for 95% occupied rate before major eviction problems.
* Extend nodeinfo cache for psram devices.
* Refactor traffic management to make hop exhaustion packet-scoped. Nice catch.
* Implement better position precision sanitization in TrafficManagementModule.
* Added logic in TrafficManagementModule to invalidate stale traffic state. Also, added some tests to avoid future me from creating a regression here.
* Fixing tests for native
* Enhance TrafficManagementModule to improve NodeInfo response handling and position deduplication logic. Added tests to ensure local packets bypass transit filters and that NodeInfo requests correctly update the requester information in the cache. Updated deduplication checks to prevent dropping valid position packets under certain conditions.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Fixes this build error:
<command-line>: error: expected unqualified-id before '-' token
/home/<snip>/.platformio/packages/framework-arduinoespressif32/variants/esp32s3/pins_arduino.h:15:22: note: in expansion of macro 'LED_BUILTIN'
15 | static const uint8_t LED_BUILTIN = SOC_GPIO_PIN_COUNT + PIN_RGB_LED;
| ^~~~~~~~~~~
More info: https://github.com/meshtastic/firmware/pull/9122#issuecomment-4028263894
The fix is consistent with variants/esp32s3/heltec_v3/platformio.ini
This commit is intentionally on the develop branch, because it's harmless to
develop branch, and makes us more ready for pioarduino when the time comes.
Heltec v4 introduced in: https://github.com/meshtastic/firmware/pull/7845
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update ESP8266Audio dependency to Meshtastic fork for compatibility
* Update ESP8266Audio dependency to Meshtastic fork for compatibility across multiple platformio.ini files
Addendum to PR #9791
The sourcedebs cannot currently be built offline >30 days after release. Extend the cache-expiry-mangling hack to sourcedeb packaging.
socketSendUDP() calls yield() while waiting for SEND_OK, allowing the
cooperative scheduler to run AsyncUDP::runOnce(). When runOnce() calls
parsePacket() on the same socket during an active send, the multicast
loopback packet arriving from the switch produces a garbled 8-byte RX
header (wrong source IP, wrong payload length), leading to protobuf
decode errors in UdpMulticastHandler.
Add a volatile isSending flag that writeTo() sets around endPacket()
(the only yield point). runOnce() checks this flag and skips
parsePacket() while a send is in progress. Loopback packets stay
buffered in the W5100S RX buffer and are read cleanly on the next
poll cycle.
Also propagate writeTo() return value in UdpMulticastHandler::onSend()
instead of unconditionally returning true.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Nodelist cleanup
* Trunk fix
* getTextWidth cleanup
Updated the lambda to cache width in textW and reuse it instead of repeatedly calling getTextWidth(text) for unchanged text.
* Putting back hopAway ==0 condition as mentioned relayed signal is missleading
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update Heltec Tracker v2 to version KCT8103L.
* Fixed the issue of inaccurate comments.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
P0.04 is a digital power-enable pin for the NTC/LUX sensors, not an ADC
input. The old code was calling analogRead() on a floating GPIO that
happened to read ~mid-rail, coincidentally producing reasonable
temperature values.
- Rename T1000X_VCC_PIN to T1000X_SENSOR_EN_PIN and drive it HIGH in
initVariant() for both T1000-E and T1000-S variants
- Read BATTERY_PIN (with ADC_MULTIPLIER) instead, clamped to the 3.0V
LDO output (NTC_REF_VCC) for the NTC resistance calculation
* Cardputer Kit
BMI270 WIP
* BMI270 support
* verify that the number of bytes read matches the requested length
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* trunk'd
* remove excessive logging
* Kick the screen when unsleeping
* Update the st7789 library, and enable displayon and displayoff
* Battery detection
* Default to arrow keys and enter, while in menus.
* Enable Backlight control
* Update src/detect/ScanI2CTwoWire.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* updateState method now accepts shouldRequestFocus parameter for better maintainability
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add Portduino Enable pins
* Add hat plus custom fields
* Punt on the GPIO device detection for now
* Simplify TX_GAIN_LORA for RAK13302
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This fixes builds in very clean environment with default build target (e.g.
-t buildfs *not* explicitly specified).
Tested: pio run -e heltec-v3
Fixes#9035
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Adds ROUTER_LATE and CLIENT_BASE to preferred rebroadcaster check
(skip unsolicited NodeInfo) and prevents ROUTER_LATE from setting
rebroadcast mode to NONE, which would silently break relaying.
ROUTER_LATE is an infrastructure relay that should use the same power
assumptions, interval defaults, and LoRa wake behavior as ROUTER.
Without this, ROUTER_LATE uses client-class defaults and will not
wake on LoRa activity from deep sleep, making it a broken relay.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE already has high base intervals and should not be further
scaled by congestion. TAK_TRACKER is a tracker variant that should
skip congestion scaling like TRACKER does.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER and ROUTER_LATE should not accumulate favorites by sending DMs.
Also replaces magic number 12 with meshtastic_Config_DeviceConfig_Role_CLIENT_BASE.
ROUTER_LATE should be treated as an impolite telemetry role like
ROUTER, responding to multi-hop broadcast requests and using
aggressive send timing without channel utilization checks.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE now preserves node_info_broadcast_secs during factory
reset and auto-enables Store & Forward server mode, matching ROUTER
infrastructure behavior.
* refactor: update throttling factor calculation and add unit tests for scaling behavior
* refactor: adjust throttling factor calculation for improved accuracy in different configurations
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* refactor: enhance throttling factor calculation and introduce pow_of_2 utility function
* refactor: improve expected ms calculation in unit tests for Default::getConfiguredOrDefaultMsScaled
* refactor: improve scaling logic for routers and sensors in computeExpectedMs function
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improve resource cleanup on connection close
* Copilot had some good feedback. Let's just make the api a unique pointer
* Update src/mesh/api/ServerAPI.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Copilot stupidly suggesting we call protected methods
* Gotta do it in the superclasses as well
* Fix moar
* Refactor MQTT unit test to ensure proper subscription handling and clear side effects
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Added a lambda function to clear startup output in the MQTT unit test to ensure a clean state before and after the MQTT subscription process.
getByIndex allocates memory and returns dummy channel whenever
chIndex validation fails. Comment implies this may happen
when malformed packet is received. The fix changes implementation
so static dummyChannel is returned in such case.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* enhance tx queue priority management
In busy environments, especially for ROUTER_LATE role, tx queue
fills very quickly. Delayed packets became late but new packets
to be retransmitted won't be put into the tx queue as old ones
stay there for a very long time (even a minute or more). This change
makes meshtastic prioritize new packets over late packets from tx queue
and allows to remove late packet from back of tx queue when there
is no space for a new one.
* apply copilot recommendation for cast
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Don't launch canned message when waking screen or silencing notification
* Add screen ifdefs
* Get the #if right
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(MQTT): First MapReport does not get sent
Throttle::isWithinTimespanMs(last_report_to_map, map_publish_interval_msecs) is
used to maintain the map reporting interval, but because last_report_to_map has
an initial value of 0, the map report routine does not start until the system
millis() time has passed map_publish_interval_msecs.
Fix this by adding a check that last_report_to_map is not 0.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Send MapReporting immediately upon location fix
Do not update last_report_to_map when Map Report is attempted without a valid
location, as this results in waiting up to an hour (or configured Map Report
interval).
That usually happens because most nodes do not keep GPS warm, so GPS usually
locks after the first attempt at Map Report.
This change also results in the log WARNing message getting spammed until a
location is obtained, so remove the message for now.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Throttled warning when position is not available for MapReport
Signed-off-by: Andrew Yong <me@ndoo.sg>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Add transmit history for throttling that persists between reboots
* Fix RAK long press detection to prevent phantom shutdowns from floating pins
* Update test/test_transmit_history/test_main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Test fixes and placeholder for content handler tests
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Change file name from BLEDfuScure.cpp to BLEDfuSecure.cpp. Fix filenames
in documentation.
Signed-off-by: Koko <github@kokosoftware.pl>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add GPIO_DETECT_PA portduino config, and support 13302 detection with it.
* Tweak PA detect gpio to use pinMapping
* minor yaml output fixes
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
- Before starting on some new big chunk of code, it it is optional but highly recommended to open an issue first
to say "Hey, I think this idea X should be implemented and I'm starting work on it. My general plan is Y, any feedback
is appreciated." This will allow other devs to potentially save you time by not accidentially duplicating work etc...
is appreciated." This will allow other devs to potentially save you time by not accidentally duplicating work etc...
- Please do not check in files that don't have real changes
- Please do not reformat lines that you didn't have to change the code on
- We recommend using the [Visual Studio Code](https://platformio.org/install/ide?install=vscode) editor along with the ['Trunk Check' extension](https://marketplace.visualstudio.com/items?itemName=trunk.io) (In beta for windows, WSL2 for the linux version),
- We recommend using the [Visual Studio Code](https://platformio.org/install/ide?install=vscode) editor along with the ['Trunk Check' extension](https://marketplace.visualstudio.com/items?itemName=trunk.io) (In beta for windows, WSL2 for the Linux version),
because it automatically follows our indentation rules and its auto reformatting will not cause spurious changes to lines.
- If your PR fixes a bug, mention "fixes #bugnum" somewhere in your pull request description.
- If your other co-developers have comments on your PR please tweak as needed.
- Please also enable "Allow edits by maintainers".
- Please do not submit untested code.
- If you do not have the affected hardware to test your code changes adequately against regressions, please indicate this, so that contributors and commnunity members can help test your changes.
- If you do not have the affected hardware to test your code changes adequately against regressions, please indicate this, so that contributors and community members can help test your changes.
- If your PR gets accepted you can request a "Contributor" role in the Meshtastic Discord
This directory contains YAML configuration files for meshtasticd. Each file describes a specific hardware configuration, including the LoRa module and pin assignments. These configurations are used by meshtasticd to correctly interface with the hardware.
## Metadata structure
Each configuration file includes a `Meta` section that provides information about the configuration.
This configuration is consumed by configuration-selection tools.
```yaml
Meta:
name:MeshAdv-Pi E22-900M30S# A unique identifier for this configuration.
support:community# community, official, or deprecated; determined by Meshtastic Leads.
compatible:# A list of compatible products or platforms.
- raspberry-pi
```
`name`: A unique identifier for the configuration, typically reflecting the hardware it supports.
`support`: Indicates the level of support for this configuration. It can be one of the following:
-`community`: Supported by the Meshtastic community. Meshtastic Members may not possess, or have not tested this configuration.
-`official`: Fully supported by Meshtastic. Meshtastic Members have tested and verified this configuration.
-`deprecated`: No longer recommended for deployment by Meshtastic.
`compatible`: A list of compatible products or platforms that can use this configuration.
This will vary depending on the intended use case / platform.
Multiple compatible entries can be included. E.g. Armbian `BOARD` value or OpenWrt `TARGET` value.
These tags can be consumed by different configuration-selection tools, filtering based upon their platform/etc.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
