t2000-wip

* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout

PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.

Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
  in reconnectETH(); on mismatch, perform full hardware reset and
  re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
  the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
  consume limited W5100S hardware sockets

Fixes meshtastic/firmware#6970

Made-with: Cursor

* Log actual elapsed idle time instead of constant timeout value

Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.

Made-with: Cursor

* Update src/mesh/api/ServerAPI.h

Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>

* Stop UDP multicast handler during W5100S brownout recovery

After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.

Made-with: Cursor

* Address Copilot review: recovery flags and timeout constant

Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.

Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.

Made-with: Cursor

---------

Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>

.github/actions/setup-base/action.yml

@@ -8,6 +8,8 @@ runs:
       uses: actions/checkout@v6
       with:
         submodules: recursive
+        ref: ${{github.event.pull_request.head.ref}}
+        repository: ${{github.event.pull_request.head.repo.full_name}}
 
     - name: Install dependencies
       shell: bash

.github/workflows/build_debian_src.yml

@@ -16,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:
@@ -27,6 +28,8 @@ jobs:
         with:
           submodules: recursive
           path: meshtasticd
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Install deps
         shell: bash
@@ -39,7 +42,6 @@ jobs:
           sudo mk-build-deps --install --remove --tool='apt-get -o Debug::pkgProblemResolver=yes --no-install-recommends --yes' debian/control
 
       - name: Import GPG key
-        if: github.event_name != 'pull_request' && github.event_name != 'pull_request_target'
         uses: crazy-max/ghaction-import-gpg@v7
         with:
           gpg_private_key: ${{ secrets.PPA_GPG_PRIVATE_KEY }}
@@ -58,7 +60,7 @@ jobs:
         run: debian/ci_pack_sdeb.sh
         env:
           SERIES: ${{ inputs.series }}
-          GPG_KEY_ID: ${{ steps.gpg.outputs.keyid || '' }}
+          GPG_KEY_ID: ${{ steps.gpg.outputs.keyid }}
           PKG_VERSION: ${{ steps.version.outputs.deb }}
 
       - name: Store binaries as an artifact

.github/workflows/build_firmware.yml

@@ -26,6 +26,8 @@ jobs:
       - uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Build ${{ inputs.platform }}
         id: build

.github/workflows/build_one_target.yml

@@ -87,7 +87,7 @@ jobs:
 
   gather-artifacts:
     permissions:
-      contents: read
+      contents: write
       pull-requests: write
     runs-on: ubuntu-latest
     needs: [version, build]

.github/workflows/daily_packaging.yml

@@ -5,7 +5,7 @@ on:
   workflow_dispatch:
   push:
     branches:
-      - develop # Default branch, same as 'cron' above
+      - master
     paths:
       - debian/**
       - "*.rpkg"
@@ -16,7 +16,7 @@ on:
       - .github/workflows/hook_copr.yml
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:

.github/workflows/docker_build.yml

@@ -37,7 +37,7 @@ on:
         value: ${{ jobs.docker-build.outputs.digest }}
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:
@@ -50,31 +50,14 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: |
           echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
         id: version
 
-      - name: Set up QEMU
-        uses: docker/setup-qemu-action@v4
-        with:
-          cache-image: true
-
-      - name: Docker setup
-        uses: docker/setup-buildx-action@v4
-        with:
-          # Add Google/Amazon DockerHub mirrors to buildkit config
-          # https://docs.docker.com/build/ci/github-actions/configure-builder/#registry-mirror
-          buildkitd-config-inline: |
-            [registry."docker.io"]
-              mirrors = ["mirror.gcr.io", "public.ecr.aws"]
-
-      - name: Sanitize platform string
-        id: sanitize_platform
-        # Replace slashes with underscores
-        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
-
       - name: Docker login
         if: ${{ inputs.push }}
         uses: docker/login-action@v4
@@ -82,6 +65,17 @@ jobs:
           username: meshtastic
           password: ${{ secrets.DOCKER_FIRMWARE_TOKEN }}
 
+      - name: Set up QEMU
+        uses: docker/setup-qemu-action@v4
+
+      - name: Docker setup
+        uses: docker/setup-buildx-action@v4
+
+      - name: Sanitize platform string
+        id: sanitize_platform
+        # Replace slashes with underscores
+        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
+
       - name: Docker tag
         id: meta
         uses: docker/metadata-action@v6
@@ -103,6 +97,3 @@ jobs:
           platforms: ${{ inputs.platform }}
           build-args: |
             PIO_ENV=${{ inputs.pio_env }}
-          # Cache image layers in GitHub Actions cache to speed up subsequent builds.
-          cache-from: type=gha
-          cache-to: type=gha,mode=max

.github/workflows/docker_manifest.yml

@@ -12,7 +12,7 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:
@@ -86,6 +86,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: |

.github/workflows/hook_copr.yml

@@ -11,7 +11,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-copr-hook:
@@ -21,6 +22,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{ github.ref }}
+          repository: ${{ github.repository }}
 
       - name: Trigger COPR build
         uses: vidplace7/copr-build@main

.github/workflows/main_matrix.yml

@@ -15,7 +15,8 @@ on:
       - "**.md"
       - version.properties
 
-  pull_request:
+  # Note: This is different from "pull_request". Need to specify ref when doing checkouts.
+  pull_request_target:
     branches:
       - master
       - develop
@@ -28,8 +29,6 @@ on:
 
   workflow_dispatch:
 
-permissions: read-all
-
 jobs:
   setup:
     strategy:
@@ -89,6 +88,8 @@ jobs:
       - uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
       - name: Check ${{ matrix.check.board }}
         uses: meshtastic/gh-action-firmware@main
         with:
@@ -125,16 +126,9 @@ jobs:
 
   test-native:
     if: ${{ !contains(github.ref_name, 'event/') && github.repository == 'meshtastic/firmware' }}
-    permissions: # Needed for dorny/test-reporter.
-      contents: read
-      actions: read
-      checks: write
     uses: ./.github/workflows/test_native.yml
 
   docker:
-    permissions: # Needed for pushing to GHCR.
-      contents: read
-      packages: write
     strategy:
       fail-fast: false
       matrix:
@@ -159,6 +153,9 @@ jobs:
   gather-artifacts:
     # trunk-ignore(checkov/CKV2_GHA_1)
     if: github.repository == 'meshtastic/firmware'
+    permissions:
+      contents: write
+      pull-requests: write
     strategy:
       fail-fast: false
       matrix:
@@ -176,6 +173,9 @@ jobs:
     steps:
       - name: Checkout code
         uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - uses: actions/download-artifact@v8
         with:
@@ -231,6 +231,13 @@ jobs:
           path: ./*.elf
           retention-days: 30
 
+      - uses: scruplelesswizard/comment-artifact@main
+        if: ${{ github.event_name == 'pull_request' }}
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          description: "Download firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip. This artifact will be available for 90 days from creation"
+          github-token: ${{ secrets.GITHUB_TOKEN }}
+
   shame:
     if: github.repository == 'meshtastic/firmware'
     continue-on-error: true
@@ -238,7 +245,7 @@ jobs:
     needs: [build]
     steps:
       - uses: actions/checkout@v6
-        if: github.event_name == 'pull_request'
+        if: github.event_name == 'pull_request_target'
         with:
           filter: blob:none # means we download all the git history but none of the commit (except ones with checkout like the head)
           fetch-depth: 0
@@ -256,26 +263,24 @@ jobs:
           overwrite: true
           path: manifests-new/*.mt.json
       - name: Find the merge base
-        if: github.event_name == 'pull_request'
+        if: github.event_name == 'pull_request_target'
         run: echo "MERGE_BASE=$(git merge-base "origin/$base" "$head")" >> $GITHUB_ENV
         env:
           base: ${{ github.base_ref }}
           head: ${{ github.sha }}
       # Currently broken (for-loop through EVERY artifact -- rate limiting)
       # - name: Download the old manifests
-      #   if: github.event_name == 'pull_request'
+      #   if: github.event_name == 'pull_request_target'
       #   run: gh run download -R "$repo" --name "manifests-$merge_base" --dir manifest-old/
       #   env:
       #     GH_TOKEN: ${{ github.token }}
       #     merge_base: ${{ env.MERGE_BASE }}
       #     repo: ${{ github.repository }}
       # - name: Do scan and post comment
-      #   if: github.event_name == 'pull_request'
+      #   if: github.event_name == 'pull_request_target'
       #   run: python3 bin/shame.py ${{ github.event.pull_request.number }} manifests-old/ manifests-new/
 
   release-artifacts:
-    permissions: # Needed for 'gh release upload'.
-      contents: write
     runs-on: ubuntu-latest
     if: ${{ github.event_name == 'workflow_dispatch' && github.repository == 'meshtastic/firmware' }}
     outputs:
@@ -301,17 +306,15 @@ jobs:
         id: release_notes
         run: |
           chmod +x ./bin/generate_release_notes.py
-          NOTES=$(./bin/generate_release_notes.py ${{ needs.version.outputs.long }} --compare-ref HEAD 2>release_notes.log)
+          NOTES=$(./bin/generate_release_notes.py ${{ needs.version.outputs.long }})
           echo "notes<<EOF" >> $GITHUB_OUTPUT
           echo "$NOTES" >> $GITHUB_OUTPUT
           echo "EOF" >> $GITHUB_OUTPUT
-          echo "### Release note range" >> $GITHUB_STEP_SUMMARY
-          cat release_notes.log >> $GITHUB_STEP_SUMMARY
         env:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
       - name: Create release
-        uses: softprops/action-gh-release@v3
+        uses: softprops/action-gh-release@v2
         id: create_release
         with:
           draft: true
@@ -369,8 +372,6 @@ jobs:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
   release-firmware:
-    permissions: # Needed for 'gh release upload'.
-      contents: write
     strategy:
       fail-fast: false
       matrix:
@@ -468,7 +469,7 @@ jobs:
       - name: Generate release notes
         run: |
           chmod +x ./bin/generate_release_notes.py
-          ./bin/generate_release_notes.py ${{ needs.version.outputs.long }} --compare-ref HEAD > ./publish/release_notes.md
+          ./bin/generate_release_notes.py ${{ needs.version.outputs.long }} > ./publish/release_notes.md
         env:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 

.github/workflows/merge_queue.yml

@@ -0,0 +1,371 @@
+name: Merge Queue
+# Not sure how concurrency works in merge_queue, removing for now.
+# concurrency:
+#   group: merge-queue-${{ github.head_ref || github.run_id }}
+#   cancel-in-progress: true
+on:
+  # Merge group is a special trigger that is used to trigger the workflow when a merge group is created.
+  merge_group:
+
+jobs:
+  setup:
+    strategy:
+      fail-fast: true
+      matrix:
+        arch:
+          - all
+          - check
+    runs-on: ubuntu-24.04
+    steps:
+      - uses: actions/checkout@v6
+      - uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+          cache: pip
+      - run: pip install -U platformio
+      - name: Generate matrix
+        id: jsonStep
+        run: |
+          if [[ "$GITHUB_HEAD_REF" == "" ]]; then
+            TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}})
+          else  
+            TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}} --level pr)
+          fi
+          echo "Name: $GITHUB_REF_NAME Base: $GITHUB_BASE_REF Ref: $GITHUB_REF"
+          echo "${{matrix.arch}}=$TARGETS" >> $GITHUB_OUTPUT
+    outputs:
+      all: ${{ steps.jsonStep.outputs.all }}
+      check: ${{ steps.jsonStep.outputs.check }}
+
+  version:
+    runs-on: ubuntu-latest
+    steps:
+      - uses: actions/checkout@v6
+      - name: Get release version string
+        run: |
+          echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
+          echo "deb=$(./bin/buildinfo.py deb)" >> $GITHUB_OUTPUT
+        id: version
+        env:
+          BUILD_LOCATION: local
+    outputs:
+      long: ${{ steps.version.outputs.long }}
+      deb: ${{ steps.version.outputs.deb }}
+
+  check:
+    needs: setup
+    strategy:
+      fail-fast: true
+      matrix:
+        check: ${{ fromJson(needs.setup.outputs.check) }}
+
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name != 'workflow_dispatch' }}
+    steps:
+      - uses: actions/checkout@v6
+      - name: Build base
+        id: base
+        uses: ./.github/actions/setup-base
+      - name: Check ${{ matrix.check.board }}
+        run: bin/check-all.sh ${{ matrix.check.board }}
+
+  build:
+    needs: [setup, version]
+    strategy:
+      matrix:
+        build: ${{ fromJson(needs.setup.outputs.all) }}
+    uses: ./.github/workflows/build_firmware.yml
+    with:
+      version: ${{ needs.version.outputs.long }}
+      pio_env: ${{ matrix.build.board }}
+      platform: ${{ matrix.build.platform }}
+
+  build-debian-src:
+    if: github.repository == 'meshtastic/firmware'
+    uses: ./.github/workflows/build_debian_src.yml
+    with:
+      series: UNRELEASED
+      build_location: local
+    secrets: inherit
+
+  package-pio-deps-native-tft:
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    uses: ./.github/workflows/package_pio_deps.yml
+    with:
+      pio_env: native-tft
+    secrets: inherit
+
+  test-native:
+    if: ${{ !contains(github.ref_name, 'event/') }}
+    uses: ./.github/workflows/test_native.yml
+
+  docker:
+    strategy:
+      fail-fast: false
+      matrix:
+        distro: [debian, alpine]
+        platform: [linux/amd64, linux/arm64, linux/arm/v7]
+        pio_env: [native, native-tft]
+        exclude:
+          - distro: alpine
+            platform: linux/arm/v7
+          - pio_env: native-tft
+            platform: linux/arm64
+          - pio_env: native-tft
+            platform: linux/arm/v7
+    uses: ./.github/workflows/docker_build.yml
+    with:
+      distro: ${{ matrix.distro }}
+      platform: ${{ matrix.platform }}
+      runs-on: ${{ contains(matrix.platform, 'arm') && 'ubuntu-24.04-arm' || 'ubuntu-24.04' }}
+      pio_env: ${{ matrix.pio_env }}
+      push: false
+
+  gather-artifacts:
+    # trunk-ignore(checkov/CKV2_GHA_1)
+    permissions:
+      contents: write
+      pull-requests: write
+    strategy:
+      fail-fast: false
+      matrix:
+        arch:
+          - esp32
+          - esp32s3
+          - esp32c3
+          - esp32c6
+          - nrf52840
+          - rp2040
+          - rp2350
+          - stm32
+    runs-on: ubuntu-latest
+    needs: [version, build]
+    steps:
+      - name: Checkout code
+        uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
+
+      - uses: actions/download-artifact@v8
+        with:
+          path: ./
+          pattern: firmware-${{matrix.arch}}-*
+          merge-multiple: true
+
+      - name: Display structure of downloaded files
+        run: ls -R
+
+      - name: Move files up
+        run: mv -b -t ./ ./bin/device-*.sh ./bin/device-*.bat
+
+      - name: Repackage in single firmware zip
+        uses: actions/upload-artifact@v7
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          overwrite: true
+          path: |
+            ./firmware-*.bin
+            ./firmware-*.uf2
+            ./firmware-*.hex
+            ./firmware-*.zip
+            ./device-*.sh
+            ./device-*.bat
+            ./littlefs-*.bin
+            ./bleota*bin
+            ./Meshtastic_nRF52_factory_erase*.uf2
+          retention-days: 30
+
+      - uses: actions/download-artifact@v8
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output
+
+      # For diagnostics
+      - name: Show artifacts
+        run: ls -lR
+
+      - name: Device scripts permissions
+        run: |
+          chmod +x ./output/device-install.sh || true
+          chmod +x ./output/device-update.sh || true
+
+      - name: Zip firmware
+        run: zip -j -9 -r ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./output
+
+      - name: Repackage in single elfs zip
+        uses: actions/upload-artifact@v7
+        with:
+          name: debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          overwrite: true
+          path: ./*.elf
+          retention-days: 30
+
+      - uses: scruplelesswizard/comment-artifact@main
+        if: ${{ github.event_name == 'pull_request' }}
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          description: "Download firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip. This artifact will be available for 90 days from creation"
+          github-token: ${{ secrets.GITHUB_TOKEN }}
+
+  release-artifacts:
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    outputs:
+      upload_url: ${{ steps.create_release.outputs.upload_url }}
+    needs:
+      - version
+      - gather-artifacts
+      - build-debian-src
+      - package-pio-deps-native-tft
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Create release
+        uses: softprops/action-gh-release@v2
+        id: create_release
+        with:
+          draft: true
+          prerelease: true
+          name: Meshtastic Firmware ${{ needs.version.outputs.long }} Alpha
+          tag_name: v${{ needs.version.outputs.long }}
+          body: |
+            Autogenerated by github action, developer should edit as required before publishing...
+
+      - name: Download source deb
+        uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-debian-${{ needs.version.outputs.deb }}~UNRELEASED-src
+          merge-multiple: true
+          path: ./output/debian-src
+
+      - name: Download `native-tft` pio deps
+        uses: actions/download-artifact@v8
+        with:
+          pattern: platformio-deps-native-tft-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output/pio-deps-native-tft
+
+      - name: Zip Linux sources
+        working-directory: output
+        run: |
+          zip -j -9 -r ./meshtasticd-${{ needs.version.outputs.deb }}-src.zip ./debian-src
+          zip -9 -r ./platformio-deps-native-tft-${{ needs.version.outputs.long }}.zip ./pio-deps-native-tft
+
+      # For diagnostics
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Add Linux sources to GtiHub Release
+        # Only run when targeting master branch with workflow_dispatch
+        if: ${{ github.ref_name == 'master' }}
+        run: |
+          gh release upload v${{ needs.version.outputs.long }} ./output/meshtasticd-${{ needs.version.outputs.deb }}-src.zip
+          gh release upload v${{ needs.version.outputs.long }} ./output/platformio-deps-native-tft-${{ needs.version.outputs.long }}.zip
+        env:
+          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
+
+  release-firmware:
+    strategy:
+      fail-fast: false
+      matrix:
+        arch:
+          - esp32
+          - esp32s3
+          - esp32c3
+          - esp32c6
+          - nrf52840
+          - rp2040
+          - rp2350
+          - stm32
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    needs: [release-artifacts, version]
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Setup Python
+        uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+
+      - uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output
+
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Device scripts permissions
+        run: |
+          chmod +x ./output/device-install.sh || true
+          chmod +x ./output/device-update.sh || true
+
+      - name: Zip firmware
+        run: zip -j -9 -r ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./output
+
+      - uses: actions/download-artifact@v8
+        with:
+          name: debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./elfs
+
+      - name: Zip debug elfs
+        run: zip -j -9 -r ./debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./elfs
+
+      # For diagnostics
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Add bins and debug elfs to GitHub Release
+        # Only run when targeting master branch with workflow_dispatch
+        if: ${{ github.ref_name == 'master' }}
+        run: |
+          gh release upload v${{ needs.version.outputs.long }} ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip
+          gh release upload v${{ needs.version.outputs.long }} ./debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip
+        env:
+          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
+
+  publish-firmware:
+    runs-on: ubuntu-24.04
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    needs: [release-firmware, version]
+    env:
+      targets: |-
+        esp32,esp32s3,esp32c3,esp32c6,nrf52840,rp2040,rp2350,stm32
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Setup Python
+        uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+
+      - uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-{${{ env.targets }}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./publish
+
+      - name: Publish firmware to meshtastic.github.io
+        uses: peaceiris/actions-gh-pages@v4
+        env:
+          # On event/* branches, use the event name as the destination prefix
+          DEST_PREFIX: ${{ contains(github.ref_name, 'event/') && format('{0}/', github.ref_name) || '' }}
+        with:
+          deploy_key: ${{ secrets.DIST_PAGES_DEPLOY_KEY }}
+          external_repository: meshtastic/meshtastic.github.io
+          publish_branch: master
+          publish_dir: ./publish
+          destination_dir: ${{ env.DEST_PREFIX }}firmware-${{ needs.version.outputs.long }}
+          keep_files: true
+          user_name: github-actions[bot]
+          user_email: github-actions[bot]@users.noreply.github.com
+          commit_message: ${{ needs.version.outputs.long }}
+          enable_jekyll: true

.github/workflows/models_issue_triage.yml

@@ -38,7 +38,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
         with:
@@ -80,7 +80,7 @@ jobs:
       # ─────────────────────────────────────────────────────────────────────────
       - name: Determine if completeness check should be skipped
         if: steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: check-skip
         with:
           script: |
@@ -134,7 +134,7 @@ jobs:
 
       - name: Process analysis result
         if: (steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == '') && steps.check-skip.outputs.should_skip != 'true' && steps.analysis.outputs.response != ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: process
         env:
           AI_RESPONSE: ${{ steps.analysis.outputs.response }}
@@ -174,7 +174,7 @@ jobs:
 
       - name: Apply triage label
         if: steps.process.outputs.label != '' && steps.process.outputs.label != 'none'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           LABEL_NAME: ${{ steps.process.outputs.label }}
         with:
@@ -200,7 +200,7 @@ jobs:
 
       - name: Comment on issue
         if: steps.process.outputs.should_comment == 'true'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           COMMENT_BODY: ${{ steps.process.outputs.comment_body }}
         with:

.github/workflows/models_pr_triage.yml

@@ -22,7 +22,7 @@ jobs:
       # Step 1: Check if PR already has automation/type labels (skip if so)
       # ─────────────────────────────────────────────────────────────────────────
       - name: Check existing labels
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: check-labels
         with:
           script: |
@@ -58,7 +58,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.check-labels.outputs.skip_all != 'true' && steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: quality-label
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
@@ -113,7 +113,7 @@ jobs:
 
       - name: Apply type label
         if: steps.check-labels.outputs.skip_all != 'true' && steps.check-labels.outputs.has_type_label != 'true' && steps.classify.outputs.response != ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           TYPE_LABEL: ${{ steps.classify.outputs.response }}
         with:

.github/workflows/package_obs.yml

@@ -18,7 +18,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:

.github/workflows/package_pio_deps.yml

@@ -16,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   pkg-pio-libdeps:
@@ -26,6 +27,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Setup Python
         uses: actions/setup-python@v6

.github/workflows/package_ppa.yml

@@ -5,8 +5,6 @@ on:
     secrets:
       PPA_GPG_PRIVATE_KEY:
         required: true
-      PPA_SFTP_PRIVATE_KEY:
-        required: true
     inputs:
       ppa_repo:
         description: Meshtastic PPA to target
@@ -18,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:
@@ -29,7 +28,6 @@ jobs:
       build_location: ppa
 
   package-ppa:
-    if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
     runs-on: ubuntu-24.04
     needs: build-debian-src
     steps:
@@ -38,12 +36,14 @@ jobs:
         with:
           submodules: recursive
           path: meshtasticd
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Install deps
         shell: bash
         run: |
           sudo apt-get update -y --fix-missing
-          sudo apt-get install -y dput openssh-client
+          sudo apt-get install -y dput
 
       - name: Import GPG key
         uses: crazy-max/ghaction-import-gpg@v7
@@ -68,42 +68,7 @@ jobs:
       - name: Display structure of downloaded files
         run: ls -lah
 
-      - name: Trust Launchpad's SSH key
+      - name: Publish with dput
+        if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
         run: |
-          mkdir -p ~/.ssh
-          ssh-keyscan -H ppa.launchpad.net >> ~/.ssh/known_hosts
-
-      - name: Setup dput config
-        env:
-          ppa_login: meshtasticorg
-        run: |
-          sudo tee /etc/meshtastic-dput.cf >/dev/null <<EOF
-          [ppa]
-          fqdn                    = ppa.launchpad.net
-          method                  = ftp
-          incoming                = ~%(ppa)s
-          login                   = anonymous
-
-          [ssh-ppa]
-          fqdn                    = ppa.launchpad.net
-          method                  = sftp
-          incoming                = ~%(ssh-ppa)s
-          login                   = ${ppa_login}
-          EOF
-
-      - name: Import SSH key
-        uses: webfactory/ssh-agent@v0.10.0
-        with:
-          ssh-private-key: ${{ secrets.PPA_SFTP_PRIVATE_KEY }}
-        id: ssh
-
-      - name: Publish with dput (sftp)
-        timeout-minutes: 30 # dput is terrible, sometimes runs 'forever'
-        env:
-          up_ppa_repo: ${{ inputs.ppa_repo }}
-          up_series: ${{ inputs.series }}
-          up_version: ${{ steps.version.outputs.deb }}
-        run: >
-          dput -c /etc/meshtastic-dput.cf
-          ssh-${up_ppa_repo}
-          meshtasticd_${up_version}~${up_series}_source.changes
+          dput ${{ inputs.ppa_repo }} meshtasticd_${{ steps.version.outputs.deb }}~${{ inputs.series }}_source.changes

.github/workflows/pr_enforce_labels.yml

@@ -13,7 +13,7 @@ jobs:
     runs-on: ubuntu-latest
     steps:
       - name: Check for PR labels
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         with:
           script: |
             const labels = context.payload.pull_request.labels.map(label => label.name);

.github/workflows/pr_tests.yml

@@ -177,7 +177,7 @@ jobs:
 
       - name: Comment test results on PR
         if: github.event_name == 'pull_request' && needs.native-tests.result != 'skipped'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         with:
           script: |
             const fs = require('fs');

.github/workflows/test_native.yml

@@ -16,6 +16,8 @@ jobs:
     steps:
       - uses: actions/checkout@v6
         with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
           submodules: recursive
 
       - name: Setup native build
@@ -70,6 +72,8 @@ jobs:
     steps:
       - uses: actions/checkout@v6
         with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
           submodules: recursive
 
       - name: Setup native build
@@ -124,6 +128,9 @@ jobs:
     if: always()
     steps:
       - uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
@@ -136,7 +143,7 @@ jobs:
           merge-multiple: true
 
       - name: Test Report
-        uses: dorny/test-reporter@v3.0.0
+        uses: dorny/test-reporter@v2.6.0
         with:
           name: PlatformIO Tests
           path: testreport.xml

.github/workflows/tests.yml

@@ -52,7 +52,7 @@ jobs:
           node-version: 24
 
       - name: Setup pnpm
-        uses: pnpm/action-setup@v6
+        uses: pnpm/action-setup@v4
         with:
           version: latest
 

.github/workflows/update_protobufs.yml

@@ -6,7 +6,7 @@ permissions: read-all
 jobs:
   update-protobufs:
     runs-on: ubuntu-latest
-    permissions: # Needed for peter-evans/create-pull-request.
+    permissions:
       contents: write
       pull-requests: write
     steps:

.trunk/trunk.yaml

@@ -8,27 +8,27 @@ plugins:
       uri: https://github.com/trunk-io/plugins
 lint:
   enabled:
-    - checkov@3.2.517
-    - renovate@43.110.9
+    - checkov@3.2.508
+    - renovate@43.76.3
     - prettier@3.8.1
-    - trufflehog@3.94.3
+    - trufflehog@3.93.8
     - yamllint@1.38.0
     - bandit@1.9.4
     - trivy@0.69.3
     - taplo@0.10.0
-    - ruff@0.15.9
+    - ruff@0.15.6
     - isort@8.0.1
     - markdownlint@0.48.0
     - oxipng@10.1.0
     - svgo@4.0.1
-    - actionlint@1.7.12
+    - actionlint@1.7.11
     - flake8@7.3.0
     - hadolint@2.14.0
     - shfmt@3.6.0
     - shellcheck@0.11.0
     - black@26.3.1
     - git-diff-check
-    - gitleaks@8.30.1
+    - gitleaks@8.30.0
     - clang-format@16.0.3
   ignore:
     - linters: [ALL]

bin/config.d/OpenWRT/BananaPi-BPI-R4-sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: BananaPi-BPI-R4-sx1262
-  support: community
-  compatible:
-    - bananapi_bpi-r4 # OpenWrt target
-
 Lora:
   Module: sx1262  # BananaPi-BPI-R4 SPI via 26p GPIO Header
 ##  CS: 28

bin/config.d/OpenWRT/OpenWRT-One-mikroBUS-LR-IOT-CLICK.yaml

@@ -1,10 +1,4 @@
 ##  https://www.mikroe.com/lr-iot-click
-Meta:
-  name: OpenWRT One mikroBUS LR-IOT-CLICK
-  support: community
-  compatible:
-    - openwrt_one # OpenWrt target
-
 Lora:
   Module: lr1110  # OpenWRT ONE mikroBUS with LR-IOT-CLICK
 #  CS: 25

bin/config.d/OpenWRT/OpenWRT_One_mikroBUS_sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: OpenWRT One mikroBUS sx1262
-  support: community
-  compatible:
-    - openwrt_one # OpenWrt target
-
 Lora:
   Module: sx1262
   IRQ: 10

bin/config.d/README.md

@@ -1,28 +0,0 @@
-# meshtasticd configuration files
-
-This directory contains YAML configuration files for meshtasticd. Each file describes a specific hardware configuration, including the LoRa module and pin assignments. These configurations are used by meshtasticd to correctly interface with the hardware.
-
-## Metadata structure
-
-Each configuration file includes a `Meta` section that provides information about the configuration.
-This configuration is consumed by configuration-selection tools.
-
-```yaml
-Meta:
-  name: MeshAdv-Pi E22-900M30S # A unique identifier for this configuration.
-  support: community # community, official, or deprecated; determined by Meshtastic Leads.
-  compatible: # A list of compatible products or platforms.
-    - raspberry-pi
-```
-`name`: A unique identifier for the configuration, typically reflecting the hardware it supports.
-
-`support`: Indicates the level of support for this configuration. It can be one of the following:
-
-- `community`: Supported by the Meshtastic community. Meshtastic Members may not possess, or have not tested this configuration.
-- `official`: Fully supported by Meshtastic. Meshtastic Members have tested and verified this configuration.
-- `deprecated`: No longer recommended for deployment by Meshtastic.
-
-`compatible`: A list of compatible products or platforms that can use this configuration.
-This will vary depending on the intended use case / platform.
-Multiple compatible entries can be included. E.g. Armbian `BOARD` value or OpenWrt `TARGET` value.
-These tags can be consumed by different configuration-selection tools, filtering based upon their platform/etc.

bin/config.d/display-waveshare-1-44.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare 1.44inch LCD HAT
-  support: community
-  compatible:
-    - raspberry-pi
-
 ### Waveshare 1.44inch LCD HAT
 Display:
   Panel: ST7735S

bin/config.d/display-waveshare-2.8.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare 2.8inch LCD HAT
-  support: community
-  compatible:
-    - raspberry-pi
-
 Display:
 
 ### Waveshare 2.8inch RPi LCD

bin/config.d/femtofox/femtofox_LR1121_TCXO.yaml

@@ -1,22 +1,20 @@
----
-Meta:
-  name: Femtofox Ebyte E80-900M22S with TCXO
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E80-900M22S
-## This is a bit experimental
-## 
-##
-  Module: lr1121
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO3_TCXO_VOLTAGE: 1.8
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E80-900M22S
+## This is a bit experimental
+## 
+##
+  Module: lr1121
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO3_TCXO_VOLTAGE: 1.8
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+
+
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_SX1262_TCXO.yaml

@@ -1,24 +1,21 @@
----
-Meta:
-  name: Femtofox SX1262 TCXO
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E22-900M30S, E22-900M22S with or without external RF switching setup
-## HT-RA62 (Has internal switching, but whatever)
-## Seeed WIO SX1262 (already has TXEN-DIO2 link, but needs RXEN)
-## Will work with any module with or without RF switching, and with TCXO
-  Module: sx1262
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
-#  TXen: bridge to DIO2 on E22 module
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E22-900M30S, E22-900M22S with or without external RF switching setup
+## HT-RA62 (Has internal switching, but whatever)
+## Seeed WIO SX1262 (already has TXEN-DIO2 link, but needs RXEN)
+## Will work with any module with or without RF switching, and with TCXO
+  Module: sx1262
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
+#  TXen: bridge to DIO2 on E22 module
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_SX1262_XTAL.yaml

@@ -1,24 +1,21 @@
----
-Meta:
-  name: Femtofox SX1262 XTAL
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E22-900MM22S with no external RF switching setup
-## Waveshare SX126X XXXM, AI Thinker RA-01SH
-## Will work with any module with or without RF switching and no TCXO
-
-  Module: sx1262  
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: false
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1 
-  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
-#  TXen: bridge to DIO2 on E22 module
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E22-900MM22S with no external RF switching setup
+## Waveshare SX126X XXXM, AI Thinker RA-01SH
+## Will work with any module with or without RF switching and no TCXO
+
+  Module: sx1262  
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: false
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1 
+  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
+#  TXen: bridge to DIO2 on E22 module
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+
+General:
+  MACAddressSource: eth0

bin/config.d/lora-Adafruit-RFM9x.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Adafruit RFM9x
-  support: deprecated
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: RF95  # Adafruit RFM9x
   Reset: 25

bin/config.d/lora-MeshAdv-900M30S.yaml

@@ -1,11 +1,5 @@
 # MeshAdv-Pi E22-900M30S
 # https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262
   CS: 21

bin/config.d/lora-MeshAdv-Mini-900M22S.yaml

@@ -1,11 +1,5 @@
 # MeshAdv Mini E22-900M22S
 # https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Ebyte E22-900M22S 
   CS: 8

bin/config.d/lora-RAK6421-13300-slot1.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13300 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-RAK6421-13300-slot2.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
-  ### RAK13300 in Slot 2 pins
+  ### RAK13300in Slot 2 pins
   IRQ: 18 #IO6
   Reset: 24 # IO4
   Busy: 19 # IO5

bin/config.d/lora-RAK6421-13302-slot1.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13302 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-RAK6421-13302-slot2.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
-  ### RAK13302 in Slot 2 pins
+  ### RAK13300in Slot 2 pins
   IRQ: 18 #IO6
   Reset: 24 # IO4
   Busy: 19 # IO5

bin/config.d/lora-ecb41-pge-MeshAdv-900M30S.yaml

@@ -1,39 +0,0 @@
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_A1 (physical 40)
-    pin: 1
-    gpiochip: 0
-    line: 1
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO0_B4 (physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  TXen: # GPIO1_D1 (physical 33)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  RXen: # GPIO1_B3 (physical 32)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-MeshAdv-Mini-900M22S.yaml

@@ -1,33 +0,0 @@
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_B6 (physical 24, SPI1_CSN0)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO1_C3 (physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  RXen: # GPIO1_B3 (physical 32)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot1.yaml

@@ -1,38 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6, physical 15)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO0_A3 (IO4, physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO1_C3 (IO5, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 43 # GPIO1_B3 (physical 32)
-      gpiochip: 1
-      line: 11
-    - pin: 57 # GPIO1_D1 (physical 33)
-      gpiochip: 1
-      line: 25
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
-  #   pin: 14
-  #   gpiochip: 0
-  #   line: 14

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot2.yaml

@@ -1,36 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B4 (IO6, physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Reset: # GPIO1_C3 (IO4, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  Busy: # GPIO0_B3 (IO5, physical 35)
-    pin: 11
-    gpiochip: 0
-    line: 11
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 37)
-      gpiochip: 0
-      line: 2
-    - pin: 50 # GPIO1_C2 (physical 16)
-      gpiochip: 1
-      line: 18
-  spidev: spidev0.1
-  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
-  #   pin: 7
-  #   gpiochip: 0
-  #   line: 7

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot1.yaml

@@ -1,39 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6, physical 15)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO0_A3 (IO4, physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO1_C3 (IO5, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 43 # GPIO1_B3 (physical 32)
-      gpiochip: 1
-      line: 11
-    - pin: 57 # GPIO1_D1 (physical 33)
-      gpiochip: 1
-      line: 25
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
-  #   pin: 14
-  #   gpiochip: 0
-  #   line: 14
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot2.yaml

@@ -1,37 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B4 (IO6, physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Reset: # GPIO1_C3 (IO4, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  Busy: # GPIO0_B3 (IO5, physical 35)
-    pin: 11
-    gpiochip: 0
-    line: 11
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 37)
-      gpiochip: 0
-      line: 2
-    - pin: 50 # GPIO1_C2 (physical 16)
-      gpiochip: 1
-      line: 18
-  spidev: spidev0.1
-  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
-  #   pin: 7
-  #   gpiochip: 0
-  #   line: 7
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-waveshare-sxxx.yaml

@@ -1,30 +0,0 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_A1 (physical 40)
-    pin: 1
-    gpiochip: 0
-    line: 1
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO0_B4 (physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  SX126X_ANT_SW: # GPIO1_B2 (physical 31)
-    pin: 42
-    gpiochip: 1
-    line: 10
-  spidev: spidev0.0

bin/config.d/lora-hat-rak-6421-pi-hat.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1 (Autoconf default)
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13300 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-lyra-picocalc-wio-sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Luckfox Lyra PicoCalc Wio LoRa SX1262
-  support: official
-  compatible:
-    - luckfox-lyra-plus # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ultra_1w.yaml

@@ -2,13 +2,6 @@
 # Enable overlay 'luckfox-lyra-ultra-w-spi0-cs0-spidev' with armbian-config
 # https://github.com/wehooper4/Meshtastic-Hardware/tree/main/Luckfox%20Ultra%20Hat
 # 1 Watt Lyra Ultra hat
-Meta:
-  name: wehooper4 Luckfox Ultra 1W
-  support: community
-  compatible:
-    - luckfox-pico-ultra # Armbian
-    - luckfox-lyra-ultra # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ultra_2w.yaml

@@ -2,13 +2,6 @@
 # Enable overlay 'luckfox-lyra-ultra-w-spi0-cs0-spidev' with armbian-config
 # https://github.com/wehooper4/Meshtastic-Hardware/tree/main/Luckfox%20Ultra%20Hat
 # 2 Watt Lyra Ultra hat
-Meta:
-  name: wehooper4 Luckfox Ultra 2W
-  support: community
-  compatible:
-    - luckfox-pico-ultra # Armbian
-    - luckfox-lyra-ultra # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ws-raspberry-pi-pico-hat.yaml

@@ -2,12 +2,6 @@
 # Enable overlay 'luckfox-lyra-plus-spi0-cs0_rmio13-spidev' with armbian-config
 # Waveshare LoRa HAT for Raspberry Pi Pico
 # https://www.waveshare.com/wiki/Pico-LoRa-SX1262
-Meta:
-  name: Waveshare LoRa HAT for Raspberry Pi Pico
-  support: community
-  compatible:
-    - luckfox-lyra-plus # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-zero-MeshAdv-900M30S.yaml

@@ -1,39 +0,0 @@
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_C2 (physical 40)
-    pin: 18
-    gpiochip: 0
-    line: 18
-  IRQ: # GPIO1_D1 (physical 36)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1 (physical 38)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  TXen: # GPIO1_C2 (physical 33)
-    pin: 50
-    gpiochip: 1
-    line: 18
-  RXen: # GPIO1_D2 (physical 32)
-    pin: 58
-    gpiochip: 1
-    line: 26
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-lyra-zero-MeshAdv-Mini-900M22S.yaml

@@ -1,33 +0,0 @@
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_B2_d (phys 24, RPi CE0)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  IRQ: # GPIO1_D1_d (phys 36, RPi GPIO16)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1_d (phys 38, RPi GPIO20)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B4_d (phys 18, RPi GPIO24)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  RXen: # GPIO1_D2_d (phys 32, RPi GPIO12)
-    pin: 58
-    gpiochip: 1
-    line: 26
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-lyra-zero-RAK6421-13300-slot1.yaml

@@ -1,38 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO1_D1 (IO4)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_B4 (IO5)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  # Ant_sw: # GPIO1_C2 (IO3)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 58 # GPIO1_D2
-      gpiochip: 1
-      line: 26
-    - pin: 50 # GPIO1_C2
-      gpiochip: 1
-      line: 18
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B2
-  #   pin: 10
-  #   gpiochip: 0
-  #   line: 10

bin/config.d/lora-lyra-zero-RAK6421-13300-slot2.yaml

@@ -1,36 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO0_B4 (IO4)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Busy: # GPIO1_C0 (IO5)
-    pin: 48
-    gpiochip: 1
-    line: 16
-  # Ant_sw: # GPIO0_B5 (IO3)
-  #   pin: 13
-  #   gpiochip: 0
-  #   line: 13
-  Enable_Pins:
-    - pin: 51 # GPIO1_C3
-      gpiochip: 1
-      line: 19
-    - pin: 13 # GPIO0_B5
-      gpiochip: 0
-      line: 13
-  spidev: spidev0.1
-  # CS: # GPIO0_B1
-  #   pin: 9
-  #   gpiochip: 0
-  #   line: 9

bin/config.d/lora-lyra-zero-RAK6421-13302-slot1.yaml

@@ -1,39 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO1_D1 (IO4)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_B4 (IO5)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  # Ant_sw: # GPIO1_C2 (IO3)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 58 # GPIO1_D2
-      gpiochip: 1
-      line: 26
-    - pin: 50 # GPIO1_C2
-      gpiochip: 1
-      line: 18
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B2
-  #   pin: 10
-  #   gpiochip: 0
-  #   line: 10
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-lyra-zero-RAK6421-13302-slot2.yaml

@@ -1,37 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO0_B4 (IO4)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Busy: # GPIO1_C0 (IO5)
-    pin: 48
-    gpiochip: 1
-    line: 16
-  # Ant_sw: # GPIO0_B5 (IO3)
-  #   pin: 13
-  #   gpiochip: 0
-  #   line: 13
-  Enable_Pins:
-    - pin: 51 # GPIO1_C3
-      gpiochip: 1
-      line: 19
-    - pin: 13 # GPIO0_B5
-      gpiochip: 0
-      line: 13
-  spidev: spidev0.1
-  # CS: # GPIO0_B1
-  #   pin: 9
-  #   gpiochip: 0
-  #   line: 9
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-lyra-zero-waveshare-sxxx.yaml

@@ -1,30 +0,0 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_C2 (physical 40)
-    pin: 18
-    gpiochip: 0
-    line: 18
-  IRQ: # GPIO1_D1 (physical 36)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1 (physical 38)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  SX126X_ANT_SW: # GPIO1_B3 (physical 31)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  spidev: spidev0.0

bin/config.d/lora-meshstick-1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Lora Meshstick SX1262
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-ok3506-MeshAdv-900M30S.yaml

@@ -1,41 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_B0 (physical 40)
-    pin: 8
-    gpiochip: 0
-    line: 8
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  TXen: # GPIO0_A3 (physical 33)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  RXen: # GPIO0_A2 (physical 32)
-    pin: 2
-    gpiochip: 0
-    line: 2
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-ok3506-MeshAdv-Mini-900M22S.yaml

@@ -1,35 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_C3 (physical 24, SPI0_CSN0)
-    pin: 19
-    gpiochip: 0
-    line: 19
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO3_A6 (physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  RXen: # GPIO0_A2 (physical 32)
-    pin: 2
-    gpiochip: 0
-    line: 2
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-ok3506-RAK6421-13300-slot1.yaml

@@ -1,40 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO3_B5 (IO6, physical 15)
-    pin: 109
-    gpiochip: 3
-    line: 13
-  Reset: # GPIO3_B0 (IO4, physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO3_A6 (IO5, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
-  #   pin: 3
-  #   gpiochip: 0
-  #   line: 3
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 32)
-      gpiochip: 0
-      line: 2
-    - pin: 3 # GPIO0_A3 (physical 33)
-      gpiochip: 0
-      line: 3
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
-  #   pin: 19
-  #   gpiochip: 0
-  #   line: 19

bin/config.d/lora-ok3506-RAK6421-13300-slot2.yaml

@@ -1,38 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6, physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO3_A6 (IO4, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  Busy: # GPIO0_B2 (IO5, physical 35)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
-  #   pin: 103
-  #   gpiochip: 3
-  #   line: 7
-  Enable_Pins:
-    - pin: 106 # GPIO3_B2 (physical 37)
-      gpiochip: 3
-      line: 10
-    - pin: 103 # GPIO3_A7 (physical 16)
-      gpiochip: 3
-      line: 7
-  spidev: spidev0.1
-  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
-  #   pin: 15
-  #   gpiochip: 0
-  #   line: 15

bin/config.d/lora-ok3506-RAK6421-13302-slot1.yaml

@@ -1,41 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO3_B5 (IO6, physical 15)
-    pin: 109
-    gpiochip: 3
-    line: 13
-  Reset: # GPIO3_B0 (IO4, physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO3_A6 (IO5, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
-  #   pin: 3
-  #   gpiochip: 0
-  #   line: 3
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 32)
-      gpiochip: 0
-      line: 2
-    - pin: 3 # GPIO0_A3 (physical 33)
-      gpiochip: 0
-      line: 3
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
-  #   pin: 19
-  #   gpiochip: 0
-  #   line: 19
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-RAK6421-13302-slot2.yaml

@@ -1,39 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6, physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO3_A6 (IO4, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  Busy: # GPIO0_B2 (IO5, physical 35)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
-  #   pin: 103
-  #   gpiochip: 3
-  #   line: 7
-  Enable_Pins:
-    - pin: 106 # GPIO3_B2 (physical 37)
-      gpiochip: 3
-      line: 10
-    - pin: 103 # GPIO3_A7 (physical 16)
-      gpiochip: 3
-      line: 7
-  spidev: spidev0.1
-  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
-  #   pin: 15
-  #   gpiochip: 0
-  #   line: 15
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-waveshare-sxxx.yaml

@@ -1,32 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_B0 (physical 40)
-    pin: 8
-    gpiochip: 0
-    line: 8
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  SX126X_ANT_SW: # GPIO3_B3 (physical 31)
-    pin: 107
-    gpiochip: 3
-    line: 11
-  spidev: spidev0.0

bin/config.d/lora-piggystick-lr1121.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Lora Meshstick SX1262
-  support: community
-  compatible:
-    - usb
-
 Lora:
   Module: lr1121
   CS: 0

bin/config.d/lora-pinedio-usb-sx1262.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: Pinedio USB SX1262
-  support: deprecated
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0 
   IRQ: 10
-  spidev: ch341
+  spidev: ch341

bin/config.d/lora-raxda-rock2f-starter-edition-hat.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: raxda-rock2f-starter-edition-hat
-  support: community
-  compatible:
-    - rock-2f # Armbian
-
 Lora:
 
 ### Raxda Rock 2F running Armbian Linux 6.1.99-vendor-rk35xx

bin/config.d/lora-starter-edition-sx1262-i2c.yaml

@@ -1,11 +1,5 @@
 # https://www.waveshare.com/core1262-868m.htm
 # https://github.com/markbirss/lora-starter-edition-sx1262-i2c
-Meta:
-  name: lora-starter-edition-sx1262-i2c
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Starter Edition SX1262 I2C Raspberry Pi HAT
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-usb-meshstick-1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: meshstick-1262
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-meshtoad-e22.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: meshtoad-e22
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-umesh-1262-30dbm.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: umesh-1262-30dbm
-  support: community
-  compatible:
-    - clockwork-uconsole
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-umesh-1268-30dbm.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: umesh-1268-30dbm
-  support: community
-  compatible:
-    - clockwork-uconsole
-
 Lora:
   Module: sx1268
   CS: 0

bin/config.d/lora-waveshare-sxxx.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Waveshare SX126X XXXM
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-ws-raspberry-pi-pico-to-rpi-adapter.yaml

@@ -1,12 +1,5 @@
 # https://www.waveshare.com/pico-lora-sx1262-868m.htm
 # https://github.com/markbirss/lora-ws-raspberry-pi-pico-to-rpi-adapter
-
-Meta:
-  name: ws-raspberry-pico-to-rpi-adapter
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Waveshare Raspberry Pi Pico to Raspberry Pi HAT Adapter
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-ws-raspberry-pico-to-orangepi-03.yaml

@@ -15,12 +15,6 @@
 #   5     CS          24
 #   26    DIO1/IRQ    26
 
-Meta:
-  name: ws-raspberry-pico-to-orangepi-03
-  support: community
-  compatible:
-    - orange-pi-zero-3 # Armbian
-
 Lora:
   Module: sx1262  # Waveshare Raspberry Pico Lora module
   DIO2_AS_RF_SWITCH: true

bin/generate_ci_matrix.py

@@ -43,7 +43,7 @@ for pio_env in pio_envs:
   env = {
     "ci": {"board": pio_env, "platform": env_platform},
     "board_level": cfg.get(f"env:{pio_env}", "board_level", default=None),
-    "board_check": cfg.get(f"env:{pio_env}", "board_check", default="false").strip().lower() == "true",
+    "board_check": bool(cfg.get(f"env:{pio_env}", "board_check", default=False)),
   }
   all_envs.append(env)
 

bin/generate_release_notes.py

@@ -1,31 +1,25 @@
 #!/usr/bin/env python3
-"""Generate release notes from the actual release commit range."""
+"""
+Generate release notes from merged PRs on develop and master branches.
+Categorizes PRs into Enhancements and Bug Fixes/Maintenance sections.
+"""
 
-import argparse
-import json
-import re
 import subprocess
+import re
+import json
 import sys
+from datetime import datetime
 
 
-def get_last_release_tag(compare_ref, exclude_tag=None):
-    """Get the most recent version tag merged into compare_ref."""
+def get_last_release_tag():
+    """Get the most recent release tag."""
     result = subprocess.run(
-        ["git", "tag", "--merged", compare_ref, "--sort=-version:refname", "v*"],
+        ["git", "describe", "--tags", "--abbrev=0"],
         capture_output=True,
         text=True,
         check=True,
     )
-
-    for line in result.stdout.splitlines():
-        candidate = line.strip()
-        if not candidate:
-            continue
-        if exclude_tag and candidate == exclude_tag:
-            continue
-        return candidate
-
-    raise subprocess.CalledProcessError(result.returncode, result.args, output=result.stdout, stderr=result.stderr)
+    return result.stdout.strip()
 
 
 def get_tag_date(tag):
@@ -39,18 +33,18 @@ def get_tag_date(tag):
     return result.stdout.strip()
 
 
-def get_merged_prs_in_range(tag, compare_ref):
-    """Get all merged PRs in the git range between tag and compare_ref."""
+def get_merged_prs_since_tag(tag, branch):
+    """Get all merged PRs since the given tag on the specified branch."""
+    # Get commits since tag on the branch - look for PR numbers in parentheses
     result = subprocess.run(
         [
             "git",
             "log",
-            f"{tag}..{compare_ref}",
+            f"{tag}..origin/{branch}",
             "--oneline",
         ],
         capture_output=True,
         text=True,
-        check=True,
     )
 
     prs = []
@@ -71,25 +65,6 @@ def get_merged_prs_in_range(tag, compare_ref):
     return prs
 
 
-def parse_args():
-    """Parse CLI arguments."""
-    parser = argparse.ArgumentParser(
-        description="Generate release notes from the actual release commit range."
-    )
-    parser.add_argument("new_version", help="Version that will be tagged for this release")
-    parser.add_argument(
-        "--base-tag",
-        dest="base_tag",
-        help="Existing version tag to diff from. Defaults to the latest version tag merged into the compare ref.",
-    )
-    parser.add_argument(
-        "--compare-ref",
-        default="HEAD",
-        help="Git ref to diff to. Defaults to HEAD.",
-    )
-    return parser.parse_args()
-
-
 def get_pr_details(pr_number):
     """Get PR details from GitHub API via gh CLI."""
     try:
@@ -293,28 +268,28 @@ def get_new_contributors(pr_details_list, tag, repo="meshtastic/firmware"):
 
 
 def main():
-    args = parse_args()
-    new_version = args.new_version
-    compare_ref = args.compare_ref
-    current_tag = f"v{new_version}"
+    if len(sys.argv) < 2:
+        print("Usage: generate_release_notes.py <new_version>", file=sys.stderr)
+        sys.exit(1)
+
+    new_version = sys.argv[1]
 
     # Get last release tag
     try:
-        last_tag = args.base_tag or get_last_release_tag(compare_ref, exclude_tag=current_tag)
+        last_tag = get_last_release_tag()
     except subprocess.CalledProcessError:
         print("Error: Could not find last release tag", file=sys.stderr)
         sys.exit(1)
 
-    print(
-        f"Resolved release note range: {last_tag}..{compare_ref}",
-        file=sys.stderr,
-    )
+    # Collect PRs from both branches
+    all_pr_numbers = set()
 
-    try:
-        all_pr_numbers = set(get_merged_prs_in_range(last_tag, compare_ref))
-    except subprocess.CalledProcessError as e:
-        print(f"Error: Could not get PRs for range {last_tag}..{compare_ref}: {e}", file=sys.stderr)
-        sys.exit(1)
+    for branch in ["develop", "master"]:
+        try:
+            prs = get_merged_prs_since_tag(last_tag, branch)
+            all_pr_numbers.update(prs)
+        except Exception as e:
+            print(f"Warning: Could not get PRs from {branch}: {e}", file=sys.stderr)
 
     # Get details for all PRs
     enhancements = []

bin/org.meshtastic.meshtasticd.metainfo.xml

@@ -87,9 +87,6 @@
   </screenshots>
 
   <releases>
-    <release version="2.7.22" date="2026-04-06">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.22</url>
-    </release>
     <release version="2.7.21" date="2026-03-11">
       <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.21</url>
     </release>

boards/t5-epaper-s3.json

@@ -1,38 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32s3_out.ld",
-      "memory_type": "qio_opi",
-      "partitions": "default_16MB.csv"
-    },
-    "core": "esp32",
-    "extra_flags": [
-      "-DBOARD_HAS_PSRAM",
-      "-DARDUINO_RUNNING_CORE=1",
-      "-DARDUINO_EVENT_RUNNING_CORE=0",
-      "-DARDUINO_USB_CDC_ON_BOOT=1",
-      "-DARDUINO_USB_MODE=1"
-    ],
-    "f_cpu": "240000000L",
-    "f_flash": "80000000L",
-    "flash_mode": "qio",
-    "hwids": [["0x303A", "0x1001"]],
-    "mcu": "esp32s3",
-    "variant": "esp32s3"
-  },
-  "connectivity": ["wifi", "bluetooth", "lora"],
-  "debug": {
-    "openocd_target": "esp32s3.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "LilyGo T5-ePaper-S3",
-  "upload": {
-    "flash_size": "16MB",
-    "maximum_ram_size": 327680,
-    "maximum_size": 16777216,
-    "require_upload_port": true,
-    "speed": 921600
-  },
-  "url": "https://lilygo.cc/products/t5-e-paper-s3-pro",
-  "vendor": "LILYGO"
-}

boards/tracker-t2000-c.json

@@ -1,30 +1,30 @@
 {
   "build": {
     "arduino": {
-      "ldscript": "nrf52840_s140_v6.ld"
+      "ldscript": "nrf52840_s140_v7.ld"
     },
     "core": "nRF5",
     "cpu": "cortex-m4",
-    "extra_flags": "-DNRF52840_XXAA",
+    "extra_flags": "-DARDUINO_TRACKER_T2000_C -DNRF52840_XXAA",
     "f_cpu": "64000000L",
     "hwids": [
-      ["0x239A", "0x4405"],
+      ["0x239A", "0x8029"],
       ["0x239A", "0x0029"],
       ["0x239A", "0x002A"],
-      ["0x2886", "0x1667"]
+      ["0x239A", "0x802A"],
+      ["0x2886", "0x0057"]
     ],
-    "usb_product": "HT-n5262G",
+    "usb_product": "T2000-BOOT",
     "mcu": "nrf52840",
-    "variant": "heltec_mesh_node_t096",
-    "variants_dir": "variants",
+    "variant": "Seeed_T2000-C",
     "bsp": {
       "name": "adafruit"
     },
     "softdevice": {
       "sd_flags": "-DS140",
       "sd_name": "s140",
-      "sd_version": "6.1.1",
-      "sd_fwid": "0x00B6"
+      "sd_version": "7.3.0",
+      "sd_fwid": "0x0123"
     },
     "bootloader": {
       "settings_addr": "0xFF000"
@@ -33,22 +33,28 @@
   "connectivity": ["bluetooth"],
   "debug": {
     "jlink_device": "nRF52840_xxAA",
-    "onboard_tools": ["jlink"],
     "svd_path": "nrf52840.svd",
     "openocd_target": "nrf52840-mdk-rs"
   },
   "frameworks": ["arduino"],
-  "name": "Heltec nrf (Adafruit BSP)",
+  "name": "Seeed T2000-C",
   "upload": {
     "maximum_ram_size": 248832,
     "maximum_size": 815104,
     "speed": 115200,
     "protocol": "nrfutil",
-    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
+    "protocols": [
+      "jlink",
+      "nrfjprog",
+      "nrfutil",
+      "stlink",
+      "cmsis-dap",
+      "blackmagic"
+    ],
     "use_1200bps_touch": true,
     "require_upload_port": true,
     "wait_for_upload_port": true
   },
-  "url": "https://heltec.org/",
-  "vendor": "Heltec"
+  "url": "https://www.seeedstudio.com/",
+  "vendor": "Seeed Studio"
 }

boards/ttgo-tbeam.json

@@ -1,29 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32_out.ld"
-    },
-    "core": "esp32",
-    "extra_flags": "-DARDUINO_T_Beam",
-    "f_cpu": "240000000L",
-    "f_flash": "40000000L",
-    "flash_mode": "dio",
-    "mcu": "esp32",
-    "variant": "tbeam"
-  },
-  "connectivity": ["wifi", "bluetooth", "can", "ethernet"],
-  "debug": {
-    "openocd_board": "esp-wroom-32.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "TTGO T-Beam (PSRAM Disabled)",
-  "upload": {
-    "flash_size": "4MB",
-    "maximum_ram_size": 1310720,
-    "maximum_size": 4194304,
-    "require_upload_port": true,
-    "speed": 460800
-  },
-  "url": "https://github.com/LilyGO/TTGO-T-Beam",
-  "vendor": "TTGO"
-}

debian/changelog

@@ -1,9 +1,3 @@
-meshtasticd (2.7.22.0) unstable; urgency=medium
-
-  * Version 2.7.22
-
- -- GitHub Actions <github-actions[bot]@users.noreply.github.com>  Mon, 06 Apr 2026 11:34:12 +0000
-
 meshtasticd (2.7.21.0) unstable; urgency=medium
 
   * Version 2.7.21

debian/ci_pack_sdeb.sh

@@ -27,10 +27,5 @@ rm -rf debian/changelog
 dch --create --distribution "$SERIES" --package "$package" --newversion "$PKG_VERSION~$SERIES" \
 	"GitHub Actions Automatic packaging for $PKG_VERSION~$SERIES"
 
-if [[ -n $GPG_KEY_ID ]]; then
-	# Build and sign the source deb
-	debuild -S -nc -k"$GPG_KEY_ID"
-else
-	# Build the source deb without signing (forks)
-	debuild -S -nc
-fi
+# Build the source deb
+debuild -S -nc -k"$GPG_KEY_ID"

platformio.ini

@@ -77,10 +77,10 @@ lib_deps =
 	https://github.com/meshtastic/TinyGPSPlus/archive/71a82db35f3b973440044c476d4bcdc673b104f4.zip
 	# renovate: datasource=git-refs depName=meshtastic-ArduinoThread packageName=https://github.com/meshtastic/ArduinoThread gitBranch=master
 	https://github.com/meshtastic/ArduinoThread/archive/b841b0415721f1341ea41cccfb4adccfaf951567.zip
-	# renovate: datasource=github-tags depName=Nanopb packageName=nanopb/nanopb
-	https://github.com/nanopb/nanopb/archive/refs/tags/nanopb-0.4.9.1.zip
-	# renovate: datasource=github-tags depName=ErriezCRC32 packageName=Erriez/ErriezCRC32
-	https://github.com/Erriez/ErriezCRC32/archive/refs/tags/1.0.1.zip
+	# renovate: datasource=custom.pio depName=Nanopb packageName=nanopb/library/Nanopb
+	nanopb/Nanopb@0.4.91
+	# renovate: datasource=custom.pio depName=ErriezCRC32 packageName=erriez/library/ErriezCRC32
+	erriez/ErriezCRC32@1.0.1
 
 ; Used for the code analysis in PIO Home / Inspect
 check_tool = cppcheck
@@ -95,8 +95,8 @@ check_flags =
 framework = arduino
 lib_deps =
 	${env.lib_deps}
-	# renovate: datasource=github-tags depName=NonBlockingRTTTL packageName=end2endzone/NonBlockingRTTTL
-	https://github.com/end2endzone/NonBlockingRTTTL/archive/refs/tags/1.4.0.zip
+	# renovate: datasource=custom.pio depName=NonBlockingRTTTL packageName=end2endzone/library/NonBlockingRTTTL
+	end2endzone/NonBlockingRTTTL@1.4.0
 build_unflags =
 	-std=c++11
 	-std=gnu++11
@@ -107,139 +107,131 @@ build_src_filter = ${env.build_src_filter} -<platform/portduino/> -<graphics/nic
 ; Common libs for communicating over TCP/IP networks such as MQTT
 [networking_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=TBPubSubClient packageName=thingsboard/pubsubclient
-	https://github.com/thingsboard/pubsubclient/archive/refs/tags/v2.12.1.zip
-	# renovate: datasource=github-tags depName=NTPClient packageName=arduino-libraries/NTPClient
-	https://github.com/arduino-libraries/NTPClient/archive/refs/tags/3.2.1.zip
+	# renovate: datasource=custom.pio depName=TBPubSubClient packageName=thingsboard/library/TBPubSubClient
+	thingsboard/TBPubSubClient@2.12.1
+	# renovate: datasource=custom.pio depName=NTPClient packageName=arduino-libraries/library/NTPClient
+	arduino-libraries/NTPClient@3.2.1
 
 ; Extra TCP/IP networking libs for supported devices
 [networking_extra]
 lib_deps =
-	# renovate: datasource=github-tags depName=Syslog packageName=arcao/Syslog
-	https://github.com/arcao/Syslog/archive/refs/tags/v2.0.zip
+	# renovate: datasource=custom.pio depName=Syslog packageName=arcao/library/Syslog
+	arcao/Syslog@2.0.0
 
 [radiolib_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=RadioLib packageName=jgromes/RadioLib
-	https://github.com/jgromes/RadioLib/archive/refs/tags/7.6.0.zip
+	# renovate: datasource=custom.pio depName=RadioLib packageName=jgromes/library/RadioLib
+	jgromes/RadioLib@7.6.0
 
 [device-ui_base]
 lib_deps =
 	# renovate: datasource=git-refs depName=meshtastic/device-ui packageName=https://github.com/meshtastic/device-ui gitBranch=master
-	https://github.com/meshtastic/device-ui/archive/1897dd17fceb1f101bb1a3245680aa3439edcfdd.zip
+	https://github.com/meshtastic/device-ui/archive/622b034d8791153de9d16a473723cb8625d35839.zip
 
 ; Common libs for environmental measurements in telemetry module
 [environmental_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=Adafruit BusIO packageName=adafruit/Adafruit_BusIO
-	https://github.com/adafruit/Adafruit_BusIO/archive/refs/tags/1.17.4.zip
-	# renovate: datasource=github-tags depName=Adafruit Unified Sensor packageName=adafruit/Adafruit_Sensor
-	https://github.com/adafruit/Adafruit_Sensor/archive/refs/tags/1.1.15.zip
-	# renovate: datasource=github-tags depName=Adafruit GFX packageName=adafruit/Adafruit-GFX-Library
-	https://github.com/adafruit/Adafruit-GFX-Library/archive/refs/tags/1.12.6.zip
-	# renovate: datasource=github-tags depName=NeoPixel packageName=adafruit/Adafruit_NeoPixel
-	https://github.com/adafruit/Adafruit_NeoPixel/archive/refs/tags/1.15.4.zip
-	# renovate: datasource=github-tags depName=Adafruit SSD1306 packageName=adafruit/Adafruit_SSD1306
-	https://github.com/adafruit/Adafruit_SSD1306/archive/refs/tags/2.5.16.zip
-	# renovate: datasource=github-tags depName=Adafruit BMP280 packageName=adafruit/Adafruit_BMP280_Library
-	https://github.com/adafruit/Adafruit_BMP280_Library/archive/refs/tags/3.0.0.zip
-	# renovate: datasource=github-tags depName=Adafruit BMP085 packageName=adafruit/Adafruit-BMP085-Library
-	https://github.com/adafruit/Adafruit-BMP085-Library/archive/refs/tags/1.2.4.zip
-	# renovate: datasource=github-tags depName=Adafruit BME280 packageName=adafruit/Adafruit_BME280_Library
-	https://github.com/adafruit/Adafruit_BME280_Library/archive/refs/tags/2.3.0.zip
-	# renovate: datasource=github-tags depName=Adafruit DPS310 packageName=adafruit/Adafruit_DPS310
-	https://github.com/adafruit/Adafruit_DPS310/archive/refs/tags/1.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SH110x packageName=adafruit/Adafruit_SH110x
-	https://github.com/adafruit/Adafruit_SH110x/archive/refs/tags/2.1.14.zip
-	# renovate: datasource=github-tags depName=Adafruit MCP9808 packageName=adafruit/Adafruit_MCP9808_Library
-	https://github.com/adafruit/Adafruit_MCP9808_Library/archive/refs/tags/2.0.2.zip
-	# renovate: datasource=github-tags depName=Adafruit INA260 packageName=adafruit/Adafruit_INA260
-	https://github.com/adafruit/Adafruit_INA260/archive/refs/tags/1.5.3.zip
-	# renovate: datasource=github-tags depName=Adafruit INA219 packageName=adafruit/Adafruit_INA219
-	https://github.com/adafruit/Adafruit_INA219/archive/refs/tags/1.2.3.zip
-	# renovate: datasource=github-tags depName=Adafruit MPU6050 packageName=adafruit/Adafruit_MPU6050
-	https://github.com/adafruit/Adafruit_MPU6050/archive/refs/tags/2.2.9.zip
-	# renovate: datasource=github-tags depName=Adafruit LIS3DH packageName=adafruit/Adafruit_LIS3DH
-	https://github.com/adafruit/Adafruit_LIS3DH/archive/refs/tags/1.3.0.zip
-	# renovate: datasource=github-tags depName=Adafruit AHTX0 packageName=adafruit/Adafruit_AHTX0
-	https://github.com/adafruit/Adafruit_AHTX0/archive/refs/tags/2.0.6.zip
-	# renovate: datasource=github-tags depName=Adafruit LSM6DS packageName=adafruit/Adafruit_LSM6DS
-	https://github.com/adafruit/Adafruit_LSM6DS/archive/refs/tags/4.7.4.zip
-	# renovate: datasource=github-tags depName=Adafruit TSL2591 packageName=adafruit/Adafruit_TSL2591_Library
-	https://github.com/adafruit/Adafruit_TSL2591_Library/archive/refs/tags/1.4.5.zip
-	# renovate: datasource=github-tags depName=EmotiBit MLX90632 packageName=emotibit/EmotiBit_MLX90632
-	https://github.com/EmotiBit/EmotiBit_MLX90632/archive/refs/tags/v1.0.8.zip
-	# renovate: datasource=github-tags depName=Adafruit MLX90614 packageName=adafruit/Adafruit_MLX90614
-	https://github.com/adafruit/Adafruit-MLX90614-Library/archive/refs/tags/2.1.6.zip
+	# renovate: datasource=custom.pio depName=Adafruit BusIO packageName=adafruit/library/Adafruit BusIO
+	adafruit/Adafruit BusIO@1.17.4
+	# renovate: datasource=custom.pio depName=Adafruit Unified Sensor packageName=adafruit/library/Adafruit Unified Sensor
+	adafruit/Adafruit Unified Sensor@1.1.15
+	# renovate: datasource=custom.pio depName=Adafruit BMP280 packageName=adafruit/library/Adafruit BMP280 Library
+	adafruit/Adafruit BMP280 Library@3.0.0
+	# renovate: datasource=custom.pio depName=Adafruit BMP085 packageName=adafruit/library/Adafruit BMP085 Library
+	adafruit/Adafruit BMP085 Library@1.2.4
+	# renovate: datasource=custom.pio depName=Adafruit BME280 packageName=adafruit/library/Adafruit BME280 Library
+	adafruit/Adafruit BME280 Library@2.3.0
+	# renovate: datasource=custom.pio depName=Adafruit DPS310 packageName=adafruit/library/Adafruit DPS310
+	adafruit/Adafruit DPS310@1.1.6
+	# renovate: datasource=custom.pio depName=Adafruit MCP9808 packageName=adafruit/library/Adafruit MCP9808 Library
+	adafruit/Adafruit MCP9808 Library@2.0.2
+	# renovate: datasource=custom.pio depName=Adafruit INA260 packageName=adafruit/library/Adafruit INA260 Library
+	adafruit/Adafruit INA260 Library@1.5.3
+	# renovate: datasource=custom.pio depName=Adafruit INA219 packageName=adafruit/library/Adafruit INA219
+	adafruit/Adafruit INA219@1.2.3
+	# renovate: datasource=custom.pio depName=Adafruit MPU6050 packageName=adafruit/library/Adafruit MPU6050
+	adafruit/Adafruit MPU6050@2.2.9
+	# renovate: datasource=custom.pio depName=Adafruit LIS3DH packageName=adafruit/library/Adafruit LIS3DH
+	adafruit/Adafruit LIS3DH@1.3.0
+	# renovate: datasource=custom.pio depName=Adafruit AHTX0 packageName=adafruit/library/Adafruit AHTX0
+	adafruit/Adafruit AHTX0@2.0.6
+	# renovate: datasource=custom.pio depName=Adafruit LSM6DS packageName=adafruit/library/Adafruit LSM6DS
+	adafruit/Adafruit LSM6DS@4.7.4
+	# renovate: datasource=custom.pio depName=Adafruit TSL2591 packageName=adafruit/library/Adafruit TSL2591 Library
+	adafruit/Adafruit TSL2591 Library@1.4.5
+	# renovate: datasource=custom.pio depName=EmotiBit MLX90632 packageName=emotibit/library/EmotiBit MLX90632
+	emotibit/EmotiBit MLX90632@1.0.8
+	# renovate: datasource=custom.pio depName=Adafruit MLX90614 packageName=adafruit/library/Adafruit MLX90614 Library
+	adafruit/Adafruit MLX90614 Library@2.1.6
 	# renovate: datasource=git-refs depName=INA3221 packageName=https://github.com/sgtwilko/INA3221 gitBranch=FixOverflow
 	https://github.com/sgtwilko/INA3221/archive/bb03d7e9bfcc74fc798838a54f4f99738f29fc6a.zip
-	# renovate: datasource=github-tags depName=QMC5883L Compass packageName=mprograms/QMC5883LCompass
-	https://github.com/mprograms/QMC5883LCompass/archive/refs/tags/v1.2.3.zip
-	# renovate: datasource=github-tags depName=DFRobot_RTU packageName=dfrobot/DFRobot_RTU
-	https://github.com/DFRobot/DFRobot_RTU/archive/refs/tags/V1.0.6.zip
+	# renovate: datasource=custom.pio depName=QMC5883L Compass packageName=mprograms/library/QMC5883LCompass
+	mprograms/QMC5883LCompass@1.2.3
+	# renovate: datasource=custom.pio depName=DFRobot_RTU packageName=dfrobot/library/DFRobot_RTU
+	dfrobot/DFRobot_RTU@1.0.6
 	# renovate: datasource=git-refs depName=DFRobot_RainfallSensor packageName=https://github.com/DFRobot/DFRobot_RainfallSensor gitBranch=master
 	https://github.com/DFRobot/DFRobot_RainfallSensor/archive/38fea5e02b40a5430be6dab39a99a6f6347d667e.zip
-	# renovate: datasource=github-tags depName=INA226 packageName=robtillaart/INA226
-	https://github.com/RobTillaart/INA226/archive/refs/tags/0.6.6.zip
-	# renovate: datasource=github-tags depName=SparkFun MAX3010x packageName=sparkfun/SparkFun_MAX3010x_Sensor_Library
-	https://github.com/sparkfun/SparkFun_MAX3010x_Sensor_Library/archive/refs/tags/v1.1.2.zip
-	# renovate: datasource=github-tags depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/SparkFun_ICM-20948_ArduinoLibrary
-	https://github.com/sparkfun/SparkFun_ICM-20948_ArduinoLibrary/archive/refs/tags/v1.3.2.zip
-	# renovate: datasource=github-tags depName=Adafruit LTR390 Library packageName=adafruit/Adafruit_LTR390
-	https://github.com/adafruit/Adafruit_LTR390/archive/refs/tags/1.1.2.zip
-	# renovate: datasource=github-tags depName=Adafruit PCT2075 packageName=adafruit/Adafruit_PCT2075
-	https://github.com/adafruit/Adafruit_PCT2075/archive/refs/tags/1.0.6.zip
-	# renovate: datasource=github-tags depName=DFRobot_BMM150 packageName=dfrobot/DFRobot_BMM150
-	https://github.com/DFRobot/DFRobot_BMM150/archive/refs/tags/V1.0.0.zip
-	# renovate: datasource=github-tags depName=Adafruit_TSL2561 packageName=adafruit/Adafruit_TSL2561
-	https://github.com/adafruit/Adafruit_TSL2561/archive/refs/tags/1.1.3.zip
-	# renovate: datasource=github-tags depName=BH1750_WE packageName=wollewald/BH1750_WE
-	https://github.com/wollewald/BH1750_WE/archive/refs/tags/1.1.10.zip
+	# renovate: datasource=custom.pio depName=INA226 packageName=robtillaart/library/INA226
+	robtillaart/INA226@0.6.6
+	# renovate: datasource=custom.pio depName=SparkFun MAX3010x packageName=sparkfun/library/SparkFun MAX3010x Pulse and Proximity Sensor Library
+	sparkfun/SparkFun MAX3010x Pulse and Proximity Sensor Library@1.1.2
+	# renovate: datasource=custom.pio depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/library/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library
+	sparkfun/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library@1.3.2
+	# renovate: datasource=custom.pio depName=Adafruit LTR390 Library packageName=adafruit/library/Adafruit LTR390 Library
+	adafruit/Adafruit LTR390 Library@1.1.2
+	# renovate: datasource=custom.pio depName=Adafruit PCT2075 packageName=adafruit/library/Adafruit PCT2075
+	adafruit/Adafruit PCT2075@1.0.6
+	# renovate: datasource=custom.pio depName=DFRobot_BMM150 packageName=dfrobot/library/DFRobot_BMM150
+	dfrobot/DFRobot_BMM150@1.0.0
+	# renovate: datasource=custom.pio depName=Adafruit_TSL2561 packageName=adafruit/library/Adafruit TSL2561
+	adafruit/Adafruit TSL2561@1.1.3
+	# renovate: datasource=custom.pio depName=BH1750_WE packageName=wollewald/library/BH1750_WE
+	wollewald/BH1750_WE@1.1.10
 
 ; Common environmental sensor libraries (not included in native / portduino)
 [environmental_extra_common]
 lib_deps =
-	# renovate: datasource=github-tags depName=Adafruit BMP3XX packageName=adafruit/Adafruit_BMP3XX
-	https://github.com/adafruit/Adafruit_BMP3XX/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit MAX1704X packageName=adafruit/Adafruit_MAX1704X
-	https://github.com/adafruit/Adafruit_MAX1704X/archive/refs/tags/1.0.3.zip
-	# renovate: datasource=github-tags depName=Adafruit SHTC3 packageName=adafruit/Adafruit_SHTC3
-	https://github.com/adafruit/Adafruit_SHTC3/archive/refs/tags/1.0.2.zip
-	# renovate: datasource=github-tags depName=Adafruit LPS2X packageName=adafruit/Adafruit_LPS2X
-	https://github.com/adafruit/Adafruit_LPS2X/archive/refs/tags/2.0.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SHT31 packageName=adafruit/Adafruit_SHT31
-	https://github.com/adafruit/Adafruit_SHT31/archive/refs/tags/2.2.2.zip
-	# renovate: datasource=github-tags depName=Adafruit VEML7700 packageName=adafruit/Adafruit_VEML7700
-	https://github.com/adafruit/Adafruit_VEML7700/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SHT4x packageName=adafruit/Adafruit_SHT4X
-	https://github.com/adafruit/Adafruit_SHT4X/archive/refs/tags/1.0.5.zip
-	# renovate: datasource=github-tags depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library
-	https://github.com/sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library/archive/refs/tags/v1.0.6.zip
+	# renovate: datasource=custom.pio depName=Adafruit BMP3XX packageName=adafruit/library/Adafruit BMP3XX Library
+	adafruit/Adafruit BMP3XX Library@2.1.6
+	# renovate: datasource=custom.pio depName=Adafruit MAX1704X packageName=adafruit/library/Adafruit MAX1704X
+	adafruit/Adafruit MAX1704X@1.0.3
+	# renovate: datasource=custom.pio depName=Adafruit SHTC3 packageName=adafruit/library/Adafruit SHTC3 Library
+	adafruit/Adafruit SHTC3 Library@1.0.2
+	# renovate: datasource=custom.pio depName=Adafruit LPS2X packageName=adafruit/library/Adafruit LPS2X
+	adafruit/Adafruit LPS2X@2.0.6
+	# renovate: datasource=custom.pio depName=Adafruit SHT31 packageName=adafruit/library/Adafruit SHT31 Library
+	adafruit/Adafruit SHT31 Library@2.2.2
+	# renovate: datasource=custom.pio depName=Adafruit VEML7700 packageName=adafruit/library/Adafruit VEML7700 Library
+	adafruit/Adafruit VEML7700 Library@2.1.6
+	# renovate: datasource=custom.pio depName=Adafruit SHT4x packageName=adafruit/library/Adafruit SHT4x Library
+	adafruit/Adafruit SHT4x Library@1.0.5
+	# renovate: datasource=custom.pio depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/library/SparkFun Qwiic Scale NAU7802 Arduino Library
+	sparkfun/SparkFun Qwiic Scale NAU7802 Arduino Library@1.0.6
 	# renovate: datasource=custom.pio depName=ClosedCube OPT3001 packageName=closedcube/library/ClosedCube OPT3001
 	closedcube/ClosedCube OPT3001@1.1.2
 	# renovate: datasource=git-refs depName=meshtastic-DFRobot_LarkWeatherStation packageName=https://github.com/meshtastic/DFRobot_LarkWeatherStation gitBranch=master
 	https://github.com/meshtastic/DFRobot_LarkWeatherStation/archive/4de3a9cadef0f6a5220a8a906cf9775b02b0040d.zip
-	# renovate: datasource=github-tags depName=Sensirion Core packageName=sensirion/arduino-core
-	https://github.com/Sensirion/arduino-core/archive/refs/tags/0.7.3.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SCD4x packageName=sensirion/arduino-i2c-scd4x
-	https://github.com/Sensirion/arduino-i2c-scd4x/archive/refs/tags/1.1.0.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SFA3x packageName=sensirion/arduino-i2c-sfa3x
-	https://github.com/Sensirion/arduino-i2c-sfa3x/archive/refs/tags/1.0.0.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SCD30 packageName=sensirion/arduino-i2c-scd30
-	https://github.com/Sensirion/arduino-i2c-scd30/archive/refs/tags/1.0.0.zip
+	# renovate: datasource=custom.pio depName=Sensirion Core packageName=sensirion/library/Sensirion Core
+	sensirion/Sensirion Core@0.7.3
+	# renovate: datasource=custom.pio depName=Sensirion I2C SCD4x packageName=sensirion/library/Sensirion I2C SCD4x
+	sensirion/Sensirion I2C SCD4x@1.1.0
+	# renovate: datasource=custom.pio depName=Sensirion I2C SFA3x packageName=sensirion/library/Sensirion I2C SFA3x
+	sensirion/Sensirion I2C SFA3x@1.0.0
+	# renovate: datasource=custom.pio depName=Sensirion I2C SCD30 packageName=sensirion/library/Sensirion I2C SCD30
+	sensirion/Sensirion I2C SCD30@1.0.0
 
 ; Environmental sensors with BSEC2 (Bosch proprietary IAQ)
 [environmental_extra]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=github-tags depName=Bosch BSEC2 packageName=boschsensortec/Bosch-BSEC2-Library
-	https://github.com/boschsensortec/Bosch-BSEC2-Library/archive/refs/tags/1.10.2610.zip
-	# renovate: datasource=github-tags depName=Bosch BME68x packageName=boschsensortec/Bosch-BME68x-Library
-	https://github.com/boschsensortec/Bosch-BME68x-Library/archive/refs/tags/v1.3.40408.zip
+	# renovate: datasource=custom.pio depName=Bosch BSEC2 packageName=boschsensortec/library/bsec2
+	boschsensortec/bsec2@1.10.2610
+	# renovate: datasource=custom.pio depName=Bosch BME68x packageName=boschsensortec/library/BME68x Sensor Library
+	boschsensortec/BME68x Sensor Library@1.3.40408
 
 ; Environmental sensors without BSEC (saves ~3.5KB DRAM for original ESP32 targets)
 [environmental_extra_no_bsec]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=github-tags depName=Adafruit_BME680 packageName=adafruit/Adafruit_BME680
-	https://github.com/adafruit/Adafruit_BME680/archive/refs/tags/2.0.6.zip
+	# renovate: datasource=custom.pio depName=adafruit/Adafruit BME680 Library packageName=adafruit/library/Adafruit BME680
+	adafruit/Adafruit BME680 Library@^2.0.5

renovate.json

@@ -4,8 +4,6 @@
     ":dependencyDashboard",
     ":semanticCommitTypeAll(chore)",
     ":ignoreModulesAndTests",
-    ":noUnscheduledUpdates",
-    "schedule:daily",
     "group:recommended",
     "replacements:all",
     "workarounds:all"

src/DebugConfiguration.cpp

@@ -98,6 +98,7 @@ Syslog &Syslog::logMask(uint8_t priMask)
 
 void Syslog::enable()
 {
+    this->_client->begin(this->_port);
     this->_enabled = true;
 }
 
@@ -165,21 +166,14 @@ inline bool Syslog::_sendLog(uint16_t pri, const char *appName, const char *mess
     if ((pri & LOG_FACMASK) == 0)
         pri = LOG_MAKEPRI(LOG_FAC(this->_priDefault), pri);
 
-    // W5100S: acquire UDP socket on-demand to avoid permanent socket consumption
-    if (!this->_client->begin(this->_port)) {
-        return false;
-    }
-
     if (this->_server != NULL) {
         result = this->_client->beginPacket(this->_server, this->_port);
     } else {
         result = this->_client->beginPacket(this->_ip, this->_port);
     }
 
-    if (result != 1) {
-        this->_client->stop();
+    if (result != 1)
         return false;
-    }
 
     this->_client->print('<');
     this->_client->print(pri);
@@ -199,8 +193,6 @@ inline bool Syslog::_sendLog(uint16_t pri, const char *appName, const char *mess
     this->_client->print(message);
     this->_client->endPacket();
 
-    this->_client->stop(); // W5100S: release UDP socket for other services
-
     return true;
 }
 

src/MessageStore.h

@@ -21,15 +21,8 @@
 // How many messages are stored (RAM + flash).
 // Define -DMESSAGE_HISTORY_LIMIT=N in build_flags to control memory usage.
 #ifndef MESSAGE_HISTORY_LIMIT
-#if defined(ARCH_ESP32) &&                                                                                                       \
-    !(defined(CONFIG_IDF_TARGET_ESP32C3) || defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32S2))
-// Baseline ESP32 (non-PSRAM variants) has limited heap; reduce message history on resource-constrained builds.
-// Override with -DMESSAGE_HISTORY_LIMIT=N if needed.
-#define MESSAGE_HISTORY_LIMIT 10
-#else
 #define MESSAGE_HISTORY_LIMIT 20
 #endif
-#endif
 
 // Internal alias used everywhere in code – do NOT redefine elsewhere.
 #define MAX_MESSAGES_SAVED MESSAGE_HISTORY_LIMIT

src/Power.cpp

@@ -35,11 +35,6 @@
 #include "nrfx_power.h"
 #endif
 
-#if defined(ARCH_NRF52)
-#include "Nrf52SaadcLock.h"
-#include "concurrency/LockGuard.h"
-#endif
-
 #if defined(DEBUG_HEAP_MQTT) && !MESHTASTIC_EXCLUDE_MQTT
 #include "mqtt/MQTT.h"
 #include "target_specific.h"
@@ -333,9 +328,6 @@ class AnalogBatteryLevel : public HasBatteryLevel
             scaled = esp_adc_cal_raw_to_voltage(raw, adc_characs);
             scaled *= operativeAdcMultiplier;
 #else // block for all other platforms
-#ifdef ARCH_NRF52
-            concurrency::LockGuard saadcGuard(concurrency::nrf52SaadcLock);
-#endif
             for (uint32_t i = 0; i < BATTERY_SENSE_SAMPLES; i++) {
                 raw += analogRead(BATTERY_PIN);
             }

src/buzz/buzz.cpp

@@ -6,11 +6,6 @@
 #include "Tone.h"
 #endif
 
-#if defined(HAS_I2S)
-#include "main.h"
-#include <unordered_map>
-#endif
-
 #if !defined(ARCH_PORTDUINO)
 extern "C" void delay(uint32_t dwMs);
 #endif
@@ -55,50 +50,6 @@ const int DURATION_1_2 = 500;  // 1/2 note
 const int DURATION_3_4 = 750;  // 3/4 note
 const int DURATION_1_1 = 1000; // 1/1 note
 
-#ifdef HAS_I2S
-void playTonesRTTTL(const ToneDuration *tone_durations, int size)
-{
-    // translate ToneDuration[] to RTTTL string and play using audioThread
-    static std::unordered_map<int, std::string> freqToNote = {
-        {NOTE_C3, "c4"},   {NOTE_CS3, "c#4"}, {NOTE_D3, "d4"},   {NOTE_DS3, "d#4"}, {NOTE_E3, "e4"},   {NOTE_F3, "f4"},
-        {NOTE_FS3, "f#4"}, {NOTE_G3, "g4"},   {NOTE_GS3, "g#4"}, {NOTE_A3, "a4"},   {NOTE_AS3, "a#4"}, {NOTE_B3, "b4"},
-        {NOTE_C4, "c5"},   {NOTE_E4, "e5"},   {NOTE_G4, "g5"},   {NOTE_A4, "a5"},   {NOTE_C5, "c6"},   {NOTE_E5, "e6"},
-        {NOTE_G5, "g6"},   {NOTE_F5, "f6"},   {NOTE_G6, "g7"},   {NOTE_E7, "e8"}};
-
-    char rtttl[128] = "tone:d=32,o=4,b=200:"; // default duration and octave
-    for (int i = 0; i < size; i++) {
-        const auto &td = tone_durations[i];
-        std::string note = "b4";
-        if (freqToNote.find(td.frequency_khz) != freqToNote.end()) {
-            note = freqToNote[td.frequency_khz];
-        }
-        int dur = 32; // default duration
-        if (td.duration_ms >= 1000)
-            dur = 1;
-        else if (td.duration_ms >= 500)
-            dur = 2;
-        else if (td.duration_ms >= 250)
-            dur = 4;
-        else if (td.duration_ms >= 125)
-            dur = 8;
-        else if (td.duration_ms >= 62)
-            dur = 16;
-        else
-            dur = 32;
-
-        char noteStr[64];
-        snprintf(noteStr, sizeof(noteStr), "%s,%d", note.c_str(), dur);
-        strncat(rtttl, noteStr, sizeof(rtttl) - strlen(rtttl) - 1);
-
-        audioThread->beginRttl(rtttl, strlen(rtttl));
-        while (audioThread->isPlaying()) {
-            delay(10);
-        }
-        return;
-    }
-}
-#endif
-
 void playTones(const ToneDuration *tone_durations, int size)
 {
     if (config.device.buzzer_mode == meshtastic_Config_DeviceConfig_BuzzerMode_DISABLED ||
@@ -106,13 +57,7 @@ void playTones(const ToneDuration *tone_durations, int size)
         // Buzzer is disabled or not set to system tones
         return;
     }
-#ifdef HAS_I2S
-    if (moduleConfig.external_notification.use_i2s_as_buzzer && audioThread) {
-        playTonesRTTTL(tone_durations, size);
-        return;
-    }
-#endif
-#if defined(PIN_BUZZER)
+#ifdef PIN_BUZZER
     if (!config.device.buzzer_gpio)
         config.device.buzzer_gpio = PIN_BUZZER;
 #endif

src/concurrency/BinarySemaphorePosix.cpp

@@ -1,85 +1,10 @@
 #include "concurrency/BinarySemaphorePosix.h"
 #include "configuration.h"
 
-#include <errno.h>
-#include <sys/time.h>
-
 #ifndef HAS_FREE_RTOS
 
 namespace concurrency
 {
-#ifdef ARCH_PORTDUINO
-
-BinarySemaphorePosix::BinarySemaphorePosix()
-{
-    if (pthread_mutex_init(&mutex, NULL) != 0) {
-        throw std::runtime_error("pthread_mutex_init failed");
-    }
-    if (pthread_cond_init(&cond, NULL) != 0) {
-        pthread_mutex_destroy(&mutex);
-        throw std::runtime_error("pthread_cond_init failed");
-    }
-    signaled = false;
-}
-
-BinarySemaphorePosix::~BinarySemaphorePosix()
-{
-    pthread_cond_destroy(&cond);
-    pthread_mutex_destroy(&mutex);
-}
-
-/**
- * Returns false if we timed out
- */
-bool BinarySemaphorePosix::take(uint32_t msec)
-{
-    pthread_mutex_lock(&mutex);
-
-    if (!signaled) {
-        struct timespec ts;
-        clock_gettime(CLOCK_REALTIME, &ts);
-
-        ts.tv_sec += msec / 1000;
-        ts.tv_nsec += (msec % 1000) * 1000000L;
-        if (ts.tv_nsec >= 1000000000L) {
-            ts.tv_sec += 1;
-            ts.tv_nsec -= 1000000000L;
-        }
-
-        while (!signaled) {
-            int rc = pthread_cond_timedwait(&cond, &mutex, &ts);
-            if (rc == ETIMEDOUT)
-                break;
-            if (rc != 0) {
-                // Some other error occurred
-                pthread_mutex_unlock(&mutex);
-                throw std::runtime_error("pthread_cond_timedwait failed: " + std::to_string(rc));
-            }
-        }
-    }
-
-    bool wasSignaled = signaled;
-    signaled = false; // consume the signal (binary semaphore)
-
-    pthread_mutex_unlock(&mutex);
-    return wasSignaled;
-}
-
-void BinarySemaphorePosix::give()
-{
-    pthread_mutex_lock(&mutex);
-    signaled = true;
-    pthread_cond_signal(&cond);
-    pthread_mutex_unlock(&mutex);
-}
-
-IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken)
-{
-    give();
-    if (pxHigherPriorityTaskWoken)
-        *pxHigherPriorityTaskWoken = true;
-}
-#else
 
 BinarySemaphorePosix::BinarySemaphorePosix() {}
 
@@ -97,8 +22,7 @@ bool BinarySemaphorePosix::take(uint32_t msec)
 void BinarySemaphorePosix::give() {}
 
 IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken) {}
-#endif
 
 } // namespace concurrency
 
-#endif
+#endif

src/concurrency/BinarySemaphorePosix.h

@@ -2,10 +2,6 @@
 
 #include "../freertosinc.h"
 
-#ifdef ARCH_PORTDUINO
-#include <pthread.h>
-#endif
-
 namespace concurrency
 {
 
@@ -13,12 +9,7 @@ namespace concurrency
 
 class BinarySemaphorePosix
 {
-
-#ifdef ARCH_PORTDUINO
-    pthread_mutex_t mutex;
-    pthread_cond_t cond;
-    bool signaled;
-#endif
+    // SemaphoreHandle_t semaphore;
 
   public:
     BinarySemaphorePosix();
@@ -36,4 +27,4 @@ class BinarySemaphorePosix
 
 #endif
 
-} // namespace concurrency
+} // namespace concurrency

src/configuration.h

@@ -78,6 +78,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 // Configuration
 // -----------------------------------------------------------------------------
 
+// Pre-hop drop handling (compile-time flag).
+#ifndef MESHTASTIC_PREHOP_DROP
+#define MESHTASTIC_PREHOP_DROP 0
+#endif
+
 /// Convert a preprocessor name into a quoted string
 #define xstr(s) ystr(s)
 #define ystr(s) #s
@@ -151,19 +156,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #ifdef USE_KCT8103L_PA
 // Power Amps are often non-linear, so we can use an array of values for the power curve
-#if defined(HELTEC_WIRELESS_TRACKER_V2)
 #define NUM_PA_POINTS 22
 #define TX_GAIN_LORA 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 13, 13, 13, 12, 12, 11, 10, 9, 8, 7
-#elif defined(HELTEC_MESH_NODE_T096)
-#define NUM_PA_POINTS 22
-#define TX_GAIN_LORA 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 13, 13, 13, 12, 11, 10, 9, 8, 7
-#else
-// If a board enables USE_KCT8103L_PA but does not match a known variant and has
-// not already provided a PA curve, fail at compile time to avoid unsafe defaults.
-#if !defined(NUM_PA_POINTS) || !defined(TX_GAIN_LORA)
-#error "USE_KCT8103L_PA is defined, but no PA gain curve (NUM_PA_POINTS / TX_GAIN_LORA) is configured for this board."
-#endif
-#endif
 #endif
 
 #ifdef RAK13302
@@ -510,6 +504,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define MESHTASTIC_EXCLUDE_REMOTEHARDWARE 1
 #define MESHTASTIC_EXCLUDE_STOREFORWARD 1
 #define MESHTASTIC_EXCLUDE_TEXTMESSAGE 1
+#define MESHTASTIC_EXCLUDE_TRAFFIC_MANAGEMENT 1
 #define MESHTASTIC_EXCLUDE_ATAK 1
 #define MESHTASTIC_EXCLUDE_CANNEDMESSAGES 1
 #define MESHTASTIC_EXCLUDE_NEIGHBORINFO 1

src/detect/ScanI2C.cpp

@@ -37,8 +37,9 @@ ScanI2C::FoundDevice ScanI2C::firstKeyboard() const
 
 ScanI2C::FoundDevice ScanI2C::firstAccelerometer() const
 {
-    ScanI2C::DeviceType types[] = {MPU6050, LIS3DH, BMA423, LSM6DS3, BMX160, STK8BAXX, ICM20948, QMA6100P, BMM150, BMI270};
-    return firstOfOrNONE(10, types);
+    ScanI2C::DeviceType types[] = {MPU6050,  LIS3DH,   BMA423,   LSM6DS3, LSM6DSOX, BMX160,
+                                   STK8BAXX, ICM20948, QMA6100P, BMM150,  BMI270};
+    return firstOfOrNONE(11, types);
 }
 
 ScanI2C::FoundDevice ScanI2C::firstAQI() const

src/detect/ScanI2C.h

@@ -47,6 +47,7 @@ class ScanI2C
         BMA423,
         BQ24295,
         LSM6DS3,
+        LSM6DSOX,
         TCA9535,
         TCA9555,
         VEML7700,

src/detect/ScanI2CTwoWire.cpp

@@ -511,6 +511,9 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                 if (registerValue == 0x6A) {
                     type = LSM6DS3;
                     logFoundDevice("LSM6DS3", (uint8_t)addr.address);
+                } else if (registerValue == 0x6C) {
+                    type = LSM6DSOX;
+                    logFoundDevice("LSM6DSOX", (uint8_t)addr.address);
                 } else {
                     type = QMI8658;
                     logFoundDevice("QMI8658", (uint8_t)addr.address);
@@ -548,7 +551,19 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
 
                 break;
 
-                SCAN_SIMPLE_CASE(LSM6DS3_ADDR, LSM6DS3, "LSM6DS3", (uint8_t)addr.address);
+            case LSM6DS3_ADDR:
+                registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x0F), 1);
+                if (registerValue == 0x6A) {
+                    type = LSM6DS3;
+                    logFoundDevice("LSM6DS3", (uint8_t)addr.address);
+                } else if (registerValue == 0x6C) {
+                    type = LSM6DSOX;
+                    logFoundDevice("LSM6DSOX", (uint8_t)addr.address);
+                } else {
+                    type = QMI8658;
+                    logFoundDevice("QMI8658", (uint8_t)addr.address);
+                }
+                break;
                 SCAN_SIMPLE_CASE(VEML7700_ADDR, VEML7700, "VEML7700", (uint8_t)addr.address);
             case TCA9555_ADDR:
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x01), 1);

src/gps/RTC.cpp

@@ -2,7 +2,6 @@
 #include "configuration.h"
 #include "detect/ScanI2C.h"
 #include "main.h"
-#include "modules/NodeInfoModule.h"
 #include <Throttle.h>
 #include <sys/time.h>
 #include <time.h>
@@ -13,14 +12,6 @@ uint32_t lastSetFromPhoneNtpOrGps = 0;
 static uint32_t lastTimeValidationWarning = 0;
 static const uint32_t TIME_VALIDATION_WARNING_INTERVAL_MS = 15000; // 15 seconds
 
-static void triggerNodeInfoCheckOnTimeSource(RTCQuality oldQuality, RTCQuality newQuality)
-{
-    if (oldQuality == RTCQualityNone && newQuality > RTCQualityNone && nodeInfoModule) {
-        LOG_DEBUG("Time source acquired (%s -> %s), triggering NodeInfo recheck", RtcName(oldQuality), RtcName(newQuality));
-        nodeInfoModule->triggerImmediateNodeInfoCheck();
-    }
-}
-
 RTCQuality getRTCQuality()
 {
     return currentQuality;
@@ -70,11 +61,9 @@ RTCSetResult readFromRTC()
         LOG_DEBUG("Read RTC time from RV3028 getTime as %02d-%02d-%02d %02d:%02d:%02d (%ld)", t.tm_year + 1900, t.tm_mon + 1,
                   t.tm_mday, t.tm_hour, t.tm_min, t.tm_sec, printableEpoch);
         if (currentQuality == RTCQualityNone) {
-            RTCQuality oldQuality = currentQuality;
             timeStartMsec = now;
             zeroOffsetSecs = tv.tv_sec;
             currentQuality = RTCQualityDevice;
-            triggerNodeInfoCheckOnTimeSource(oldQuality, currentQuality);
         }
         return RTCSetResultSuccess;
     } else {
@@ -116,11 +105,9 @@ RTCSetResult readFromRTC()
         LOG_DEBUG("Read RTC time from %s getDateTime as %02d-%02d-%02d %02d:%02d:%02d (%ld)", rtc.getChipName(), t.tm_year + 1900,
                   t.tm_mon + 1, t.tm_mday, t.tm_hour, t.tm_min, t.tm_sec, printableEpoch);
         if (currentQuality == RTCQualityNone) {
-            RTCQuality oldQuality = currentQuality;
             timeStartMsec = now;
             zeroOffsetSecs = tv.tv_sec;
             currentQuality = RTCQualityDevice;
-            triggerNodeInfoCheckOnTimeSource(oldQuality, currentQuality);
         }
         return RTCSetResultSuccess;
     } else {
@@ -152,11 +139,9 @@ RTCSetResult readFromRTC()
             }
 #endif
             if (currentQuality == RTCQualityNone) {
-                RTCQuality oldQuality = currentQuality;
                 timeStartMsec = now;
                 zeroOffsetSecs = tv.tv_sec;
                 currentQuality = RTCQualityDevice;
-                triggerNodeInfoCheckOnTimeSource(oldQuality, currentQuality);
             }
             return RTCSetResultSuccess;
         }
@@ -229,7 +214,6 @@ RTCSetResult perhapsSetRTC(RTCQuality q, const struct timeval *tv, bool forceUpd
     }
 
     if (shouldSet) {
-        RTCQuality oldQuality = currentQuality;
         currentQuality = q;
         lastSetMsec = now;
         if (currentQuality >= RTCQualityNTP) {
@@ -297,7 +281,6 @@ RTCSetResult perhapsSetRTC(RTCQuality q, const struct timeval *tv, bool forceUpd
 #endif
 
         readFromRTC();
-        triggerNodeInfoCheckOnTimeSource(oldQuality, currentQuality);
         return RTCSetResultSuccess;
     } else {
         return RTCSetResultNotSet; // RTC was already set with a higher quality time
@@ -414,17 +397,6 @@ uint32_t getValidTime(RTCQuality minQuality, bool local)
     return (currentQuality >= minQuality) ? getTime(local) : 0;
 }
 
-#ifdef PIO_UNIT_TESTING
-void setBootRelativeTimeForUnitTest(uint32_t secondsSinceBoot)
-{
-    currentQuality = RTCQualityNone;
-    zeroOffsetSecs = 0;
-    timeStartMsec = millis() - (secondsSinceBoot * 1000);
-    lastSetFromPhoneNtpOrGps = 0;
-    lastTimeValidationWarning = 0;
-}
-#endif
-
 time_t gm_mktime(const struct tm *tm)
 {
 #if !MESHTASTIC_EXCLUDE_TZ

src/gps/RTC.h

@@ -54,10 +54,6 @@ uint32_t getValidTime(RTCQuality minQuality, bool local = false);
 
 RTCSetResult readFromRTC();
 
-#ifdef PIO_UNIT_TESTING
-void setBootRelativeTimeForUnitTest(uint32_t secondsSinceBoot);
-#endif
-
 time_t gm_mktime(const struct tm *tm);
 
 #define SEC_PER_DAY 86400

src/graphics/EInkDisplay2.cpp

@@ -1,6 +1,6 @@
 #include "configuration.h"
 
-#if defined(USE_EINK) && !defined(USE_EINK_PARALLELDISPLAY)
+#ifdef USE_EINK
 #include "EInkDisplay2.h"
 #include "SPILock.h"
 #include "main.h"

src/graphics/EInkDisplay2.h

@@ -1,6 +1,6 @@
 #pragma once
 
-#if defined(USE_EINK) && !defined(USE_EINK_PARALLELDISPLAY)
+#ifdef USE_EINK
 
 #include "GxEPD2_BW.h"
 #include <OLEDDisplay.h>