t2000-wip

.github/actions/setup-base/action.yml

@@ -8,6 +8,8 @@ runs:
       uses: actions/checkout@v6
       with:
         submodules: recursive
+        ref: ${{github.event.pull_request.head.ref}}
+        repository: ${{github.event.pull_request.head.repo.full_name}}
 
     - name: Install dependencies
       shell: bash

.github/workflows/build_debian_src.yml

@@ -16,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:
@@ -27,6 +28,8 @@ jobs:
         with:
           submodules: recursive
           path: meshtasticd
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Install deps
         shell: bash
@@ -39,7 +42,6 @@ jobs:
           sudo mk-build-deps --install --remove --tool='apt-get -o Debug::pkgProblemResolver=yes --no-install-recommends --yes' debian/control
 
       - name: Import GPG key
-        if: github.event_name != 'pull_request' && github.event_name != 'pull_request_target'
         uses: crazy-max/ghaction-import-gpg@v7
         with:
           gpg_private_key: ${{ secrets.PPA_GPG_PRIVATE_KEY }}
@@ -58,7 +60,7 @@ jobs:
         run: debian/ci_pack_sdeb.sh
         env:
           SERIES: ${{ inputs.series }}
-          GPG_KEY_ID: ${{ steps.gpg.outputs.keyid || '' }}
+          GPG_KEY_ID: ${{ steps.gpg.outputs.keyid }}
           PKG_VERSION: ${{ steps.version.outputs.deb }}
 
       - name: Store binaries as an artifact

.github/workflows/build_firmware.yml

@@ -26,6 +26,8 @@ jobs:
       - uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Build ${{ inputs.platform }}
         id: build

.github/workflows/build_one_target.yml

@@ -4,14 +4,9 @@ on:
   workflow_dispatch:
     inputs:
       # trunk-ignore(checkov/CKV_GHA_7)
-      target:
-        type: string
-        required: false
-        description: Choose the target board, e.g. nrf52_promicro_diy_tcxo. If blank, will find available targets.
       arch:
         type: choice
         options:
-          - all
           - esp32
           - esp32s3
           - esp32c3
@@ -20,18 +15,32 @@ on:
           - rp2040
           - rp2350
           - stm32
-        description: Choose an arch to limit the search, or 'all' to search all architectures.
-        default: all
+      target:
+        type: string
+        required: false
+        description: Choose the target board, e.g. nrf52_promicro_diy_tcxo. If blank, will find available targets.
+      # find-target:
+      #   type: boolean
+      #   default: true
+      #   description: 'Find the available targets'
 
 permissions: read-all
 
 jobs:
   find-targets:
+    if: ${{ inputs.target == '' }}
     strategy:
       fail-fast: false
       matrix:
         arch:
-          - all
+          - esp32
+          - esp32s3
+          - esp32c3
+          - esp32c6
+          - nrf52840
+          - rp2040
+          - rp2350
+          - stm32
     runs-on: ubuntu-24.04
     steps:
       - uses: actions/checkout@v6
@@ -42,37 +51,14 @@ jobs:
       - run: pip install -U platformio
       - name: Generate matrix
         id: jsonStep
-        env:
-          BUILDTARGET: ${{ inputs.target }}
-          MATRIXARCH: ${{ inputs.arch }}
         run: |
           TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}} --level extra)
-          if [ "$BUILDTARGET" = "" ]; then
-            echo "Name: $GITHUB_REF_NAME" >> $GITHUB_STEP_SUMMARY
-            echo "Base: $GITHUB_BASE_REF" >> $GITHUB_STEP_SUMMARY
-            echo "Arch: $MATRIXARCH" >> $GITHUB_STEP_SUMMARY
-            echo "Ref: $GITHUB_REF" >> $GITHUB_STEP_SUMMARY
-            echo "## 🎯 The following target boards are available to build:" >> $GITHUB_STEP_SUMMARY
-            echo "| Platform | Board |" >> $GITHUB_STEP_SUMMARY
-            echo "| -------- | ----- |" >> $GITHUB_STEP_SUMMARY
-            echo $TARGETS | jq -r 'sort_by(.board) | sort_by(.platform) |.[] | "| " + .platform + " | " + .board + " |" ' >> $GITHUB_STEP_SUMMARY
-          else
-            echo "We build this one:" >> $GITHUB_STEP_SUMMARY
-            ARCH=$(echo "$TARGETS" | jq --arg BUILDTARGET "$BUILDTARGET" -r '.[] | select(.board==$BUILDTARGET) | .platform')
-            echo "| Platform | Board |" >> $GITHUB_STEP_SUMMARY
-            echo "| -------- | ----- |" >> $GITHUB_STEP_SUMMARY
-            echo "| $ARCH | "$BUILDTARGET" |" >> $GITHUB_STEP_SUMMARY
-            echo "" >> $GITHUB_STEP_SUMMARY
-            if [[ "$ARCH" == "" ]]; then
-              echo "## ❌ Error: Target "$BUILDTARGET" not found!" >> $GITHUB_STEP_SUMMARY
-            else
-              echo "## ✅ Target "$BUILDTARGET" found, proceeding to build." >> $GITHUB_STEP_SUMMARY
-            fi
-            echo "You may need to refresh this page to make the built firmware appear below." >> $GITHUB_STEP_SUMMARY
-            echo "arch=$ARCH" >> $GITHUB_OUTPUT
-          fi
-    outputs:
-      arch: ${{ steps.jsonStep.outputs.arch }}
+          echo "Name: $GITHUB_REF_NAME" >> $GITHUB_STEP_SUMMARY
+          echo "Base: $GITHUB_BASE_REF" >> $GITHUB_STEP_SUMMARY
+          echo "Arch: ${{matrix.arch}}" >> $GITHUB_STEP_SUMMARY
+          echo "Ref: $GITHUB_REF" >> $GITHUB_STEP_SUMMARY
+          echo "Targets:" >> $GITHUB_STEP_SUMMARY
+          echo $TARGETS | jq -r 'sort_by(.board) |.[] | "- " + .board' >> $GITHUB_STEP_SUMMARY
 
   version:
     if: ${{ inputs.target != '' }}
@@ -92,16 +78,16 @@ jobs:
 
   build:
     if: ${{ inputs.target != '' && inputs.arch != 'native' }}
-    needs: [version, find-targets]
+    needs: [version]
     uses: ./.github/workflows/build_firmware.yml
     with:
       version: ${{ needs.version.outputs.long }}
       pio_env: ${{ inputs.target }}
-      platform: ${{ needs.find-targets.outputs.arch }}
+      platform: ${{ inputs.arch }}
 
   gather-artifacts:
     permissions:
-      contents: read
+      contents: write
       pull-requests: write
     runs-on: ubuntu-latest
     needs: [version, build]

.github/workflows/daily_packaging.yml

@@ -5,7 +5,7 @@ on:
   workflow_dispatch:
   push:
     branches:
-      - develop # Default branch, same as 'cron' above
+      - master
     paths:
       - debian/**
       - "*.rpkg"
@@ -16,7 +16,7 @@ on:
       - .github/workflows/hook_copr.yml
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:

.github/workflows/docker_build.yml

@@ -37,7 +37,7 @@ on:
         value: ${{ jobs.docker-build.outputs.digest }}
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:
@@ -50,31 +50,14 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: |
           echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
         id: version
 
-      - name: Set up QEMU
-        uses: docker/setup-qemu-action@v4
-        with:
-          cache-image: true
-
-      - name: Docker setup
-        uses: docker/setup-buildx-action@v4
-        with:
-          # Add Google/Amazon DockerHub mirrors to buildkit config
-          # https://docs.docker.com/build/ci/github-actions/configure-builder/#registry-mirror
-          buildkitd-config-inline: |
-            [registry."docker.io"]
-              mirrors = ["mirror.gcr.io", "public.ecr.aws"]
-
-      - name: Sanitize platform string
-        id: sanitize_platform
-        # Replace slashes with underscores
-        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
-
       - name: Docker login
         if: ${{ inputs.push }}
         uses: docker/login-action@v4
@@ -82,6 +65,17 @@ jobs:
           username: meshtastic
           password: ${{ secrets.DOCKER_FIRMWARE_TOKEN }}
 
+      - name: Set up QEMU
+        uses: docker/setup-qemu-action@v4
+
+      - name: Docker setup
+        uses: docker/setup-buildx-action@v4
+
+      - name: Sanitize platform string
+        id: sanitize_platform
+        # Replace slashes with underscores
+        run: echo "cleaned_platform=${{ inputs.platform }}" | sed 's/\//_/g' >> $GITHUB_OUTPUT
+
       - name: Docker tag
         id: meta
         uses: docker/metadata-action@v6
@@ -103,6 +97,3 @@ jobs:
           platforms: ${{ inputs.platform }}
           build-args: |
             PIO_ENV=${{ inputs.pio_env }}
-          # Cache image layers in GitHub Actions cache to speed up subsequent builds.
-          cache-from: type=gha
-          cache-to: type=gha,mode=max

.github/workflows/docker_manifest.yml

@@ -12,7 +12,7 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
   packages: write
 
 jobs:
@@ -86,6 +86,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: |

.github/workflows/hook_copr.yml

@@ -11,7 +11,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-copr-hook:
@@ -21,6 +22,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{ github.ref }}
+          repository: ${{ github.repository }}
 
       - name: Trigger COPR build
         uses: vidplace7/copr-build@main

.github/workflows/main_matrix.yml

@@ -15,7 +15,8 @@ on:
       - "**.md"
       - version.properties
 
-  pull_request:
+  # Note: This is different from "pull_request". Need to specify ref when doing checkouts.
+  pull_request_target:
     branches:
       - master
       - develop
@@ -28,8 +29,6 @@ on:
 
   workflow_dispatch:
 
-permissions: read-all
-
 jobs:
   setup:
     strategy:
@@ -89,6 +88,8 @@ jobs:
       - uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
       - name: Check ${{ matrix.check.board }}
         uses: meshtastic/gh-action-firmware@main
         with:
@@ -125,16 +126,9 @@ jobs:
 
   test-native:
     if: ${{ !contains(github.ref_name, 'event/') && github.repository == 'meshtastic/firmware' }}
-    permissions: # Needed for dorny/test-reporter.
-      contents: read
-      actions: read
-      checks: write
     uses: ./.github/workflows/test_native.yml
 
   docker:
-    permissions: # Needed for pushing to GHCR.
-      contents: read
-      packages: write
     strategy:
       fail-fast: false
       matrix:
@@ -159,6 +153,9 @@ jobs:
   gather-artifacts:
     # trunk-ignore(checkov/CKV2_GHA_1)
     if: github.repository == 'meshtastic/firmware'
+    permissions:
+      contents: write
+      pull-requests: write
     strategy:
       fail-fast: false
       matrix:
@@ -176,6 +173,9 @@ jobs:
     steps:
       - name: Checkout code
         uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - uses: actions/download-artifact@v8
         with:
@@ -231,6 +231,13 @@ jobs:
           path: ./*.elf
           retention-days: 30
 
+      - uses: scruplelesswizard/comment-artifact@main
+        if: ${{ github.event_name == 'pull_request' }}
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          description: "Download firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip. This artifact will be available for 90 days from creation"
+          github-token: ${{ secrets.GITHUB_TOKEN }}
+
   shame:
     if: github.repository == 'meshtastic/firmware'
     continue-on-error: true
@@ -238,7 +245,7 @@ jobs:
     needs: [build]
     steps:
       - uses: actions/checkout@v6
-        if: github.event_name == 'pull_request'
+        if: github.event_name == 'pull_request_target'
         with:
           filter: blob:none # means we download all the git history but none of the commit (except ones with checkout like the head)
           fetch-depth: 0
@@ -256,26 +263,24 @@ jobs:
           overwrite: true
           path: manifests-new/*.mt.json
       - name: Find the merge base
-        if: github.event_name == 'pull_request'
+        if: github.event_name == 'pull_request_target'
         run: echo "MERGE_BASE=$(git merge-base "origin/$base" "$head")" >> $GITHUB_ENV
         env:
           base: ${{ github.base_ref }}
           head: ${{ github.sha }}
       # Currently broken (for-loop through EVERY artifact -- rate limiting)
       # - name: Download the old manifests
-      #   if: github.event_name == 'pull_request'
+      #   if: github.event_name == 'pull_request_target'
       #   run: gh run download -R "$repo" --name "manifests-$merge_base" --dir manifest-old/
       #   env:
       #     GH_TOKEN: ${{ github.token }}
       #     merge_base: ${{ env.MERGE_BASE }}
       #     repo: ${{ github.repository }}
       # - name: Do scan and post comment
-      #   if: github.event_name == 'pull_request'
+      #   if: github.event_name == 'pull_request_target'
       #   run: python3 bin/shame.py ${{ github.event.pull_request.number }} manifests-old/ manifests-new/
 
   release-artifacts:
-    permissions: # Needed for 'gh release upload'.
-      contents: write
     runs-on: ubuntu-latest
     if: ${{ github.event_name == 'workflow_dispatch' && github.repository == 'meshtastic/firmware' }}
     outputs:
@@ -309,7 +314,7 @@ jobs:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
       - name: Create release
-        uses: softprops/action-gh-release@v3
+        uses: softprops/action-gh-release@v2
         id: create_release
         with:
           draft: true
@@ -367,8 +372,6 @@ jobs:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
 
   release-firmware:
-    permissions: # Needed for 'gh release upload'.
-      contents: write
     strategy:
       fail-fast: false
       matrix:

.github/workflows/merge_queue.yml

@@ -0,0 +1,371 @@
+name: Merge Queue
+# Not sure how concurrency works in merge_queue, removing for now.
+# concurrency:
+#   group: merge-queue-${{ github.head_ref || github.run_id }}
+#   cancel-in-progress: true
+on:
+  # Merge group is a special trigger that is used to trigger the workflow when a merge group is created.
+  merge_group:
+
+jobs:
+  setup:
+    strategy:
+      fail-fast: true
+      matrix:
+        arch:
+          - all
+          - check
+    runs-on: ubuntu-24.04
+    steps:
+      - uses: actions/checkout@v6
+      - uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+          cache: pip
+      - run: pip install -U platformio
+      - name: Generate matrix
+        id: jsonStep
+        run: |
+          if [[ "$GITHUB_HEAD_REF" == "" ]]; then
+            TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}})
+          else  
+            TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}} --level pr)
+          fi
+          echo "Name: $GITHUB_REF_NAME Base: $GITHUB_BASE_REF Ref: $GITHUB_REF"
+          echo "${{matrix.arch}}=$TARGETS" >> $GITHUB_OUTPUT
+    outputs:
+      all: ${{ steps.jsonStep.outputs.all }}
+      check: ${{ steps.jsonStep.outputs.check }}
+
+  version:
+    runs-on: ubuntu-latest
+    steps:
+      - uses: actions/checkout@v6
+      - name: Get release version string
+        run: |
+          echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
+          echo "deb=$(./bin/buildinfo.py deb)" >> $GITHUB_OUTPUT
+        id: version
+        env:
+          BUILD_LOCATION: local
+    outputs:
+      long: ${{ steps.version.outputs.long }}
+      deb: ${{ steps.version.outputs.deb }}
+
+  check:
+    needs: setup
+    strategy:
+      fail-fast: true
+      matrix:
+        check: ${{ fromJson(needs.setup.outputs.check) }}
+
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name != 'workflow_dispatch' }}
+    steps:
+      - uses: actions/checkout@v6
+      - name: Build base
+        id: base
+        uses: ./.github/actions/setup-base
+      - name: Check ${{ matrix.check.board }}
+        run: bin/check-all.sh ${{ matrix.check.board }}
+
+  build:
+    needs: [setup, version]
+    strategy:
+      matrix:
+        build: ${{ fromJson(needs.setup.outputs.all) }}
+    uses: ./.github/workflows/build_firmware.yml
+    with:
+      version: ${{ needs.version.outputs.long }}
+      pio_env: ${{ matrix.build.board }}
+      platform: ${{ matrix.build.platform }}
+
+  build-debian-src:
+    if: github.repository == 'meshtastic/firmware'
+    uses: ./.github/workflows/build_debian_src.yml
+    with:
+      series: UNRELEASED
+      build_location: local
+    secrets: inherit
+
+  package-pio-deps-native-tft:
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    uses: ./.github/workflows/package_pio_deps.yml
+    with:
+      pio_env: native-tft
+    secrets: inherit
+
+  test-native:
+    if: ${{ !contains(github.ref_name, 'event/') }}
+    uses: ./.github/workflows/test_native.yml
+
+  docker:
+    strategy:
+      fail-fast: false
+      matrix:
+        distro: [debian, alpine]
+        platform: [linux/amd64, linux/arm64, linux/arm/v7]
+        pio_env: [native, native-tft]
+        exclude:
+          - distro: alpine
+            platform: linux/arm/v7
+          - pio_env: native-tft
+            platform: linux/arm64
+          - pio_env: native-tft
+            platform: linux/arm/v7
+    uses: ./.github/workflows/docker_build.yml
+    with:
+      distro: ${{ matrix.distro }}
+      platform: ${{ matrix.platform }}
+      runs-on: ${{ contains(matrix.platform, 'arm') && 'ubuntu-24.04-arm' || 'ubuntu-24.04' }}
+      pio_env: ${{ matrix.pio_env }}
+      push: false
+
+  gather-artifacts:
+    # trunk-ignore(checkov/CKV2_GHA_1)
+    permissions:
+      contents: write
+      pull-requests: write
+    strategy:
+      fail-fast: false
+      matrix:
+        arch:
+          - esp32
+          - esp32s3
+          - esp32c3
+          - esp32c6
+          - nrf52840
+          - rp2040
+          - rp2350
+          - stm32
+    runs-on: ubuntu-latest
+    needs: [version, build]
+    steps:
+      - name: Checkout code
+        uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
+
+      - uses: actions/download-artifact@v8
+        with:
+          path: ./
+          pattern: firmware-${{matrix.arch}}-*
+          merge-multiple: true
+
+      - name: Display structure of downloaded files
+        run: ls -R
+
+      - name: Move files up
+        run: mv -b -t ./ ./bin/device-*.sh ./bin/device-*.bat
+
+      - name: Repackage in single firmware zip
+        uses: actions/upload-artifact@v7
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          overwrite: true
+          path: |
+            ./firmware-*.bin
+            ./firmware-*.uf2
+            ./firmware-*.hex
+            ./firmware-*.zip
+            ./device-*.sh
+            ./device-*.bat
+            ./littlefs-*.bin
+            ./bleota*bin
+            ./Meshtastic_nRF52_factory_erase*.uf2
+          retention-days: 30
+
+      - uses: actions/download-artifact@v8
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output
+
+      # For diagnostics
+      - name: Show artifacts
+        run: ls -lR
+
+      - name: Device scripts permissions
+        run: |
+          chmod +x ./output/device-install.sh || true
+          chmod +x ./output/device-update.sh || true
+
+      - name: Zip firmware
+        run: zip -j -9 -r ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./output
+
+      - name: Repackage in single elfs zip
+        uses: actions/upload-artifact@v7
+        with:
+          name: debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          overwrite: true
+          path: ./*.elf
+          retention-days: 30
+
+      - uses: scruplelesswizard/comment-artifact@main
+        if: ${{ github.event_name == 'pull_request' }}
+        with:
+          name: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          description: "Download firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip. This artifact will be available for 90 days from creation"
+          github-token: ${{ secrets.GITHUB_TOKEN }}
+
+  release-artifacts:
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    outputs:
+      upload_url: ${{ steps.create_release.outputs.upload_url }}
+    needs:
+      - version
+      - gather-artifacts
+      - build-debian-src
+      - package-pio-deps-native-tft
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Create release
+        uses: softprops/action-gh-release@v2
+        id: create_release
+        with:
+          draft: true
+          prerelease: true
+          name: Meshtastic Firmware ${{ needs.version.outputs.long }} Alpha
+          tag_name: v${{ needs.version.outputs.long }}
+          body: |
+            Autogenerated by github action, developer should edit as required before publishing...
+
+      - name: Download source deb
+        uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-debian-${{ needs.version.outputs.deb }}~UNRELEASED-src
+          merge-multiple: true
+          path: ./output/debian-src
+
+      - name: Download `native-tft` pio deps
+        uses: actions/download-artifact@v8
+        with:
+          pattern: platformio-deps-native-tft-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output/pio-deps-native-tft
+
+      - name: Zip Linux sources
+        working-directory: output
+        run: |
+          zip -j -9 -r ./meshtasticd-${{ needs.version.outputs.deb }}-src.zip ./debian-src
+          zip -9 -r ./platformio-deps-native-tft-${{ needs.version.outputs.long }}.zip ./pio-deps-native-tft
+
+      # For diagnostics
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Add Linux sources to GtiHub Release
+        # Only run when targeting master branch with workflow_dispatch
+        if: ${{ github.ref_name == 'master' }}
+        run: |
+          gh release upload v${{ needs.version.outputs.long }} ./output/meshtasticd-${{ needs.version.outputs.deb }}-src.zip
+          gh release upload v${{ needs.version.outputs.long }} ./output/platformio-deps-native-tft-${{ needs.version.outputs.long }}.zip
+        env:
+          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
+
+  release-firmware:
+    strategy:
+      fail-fast: false
+      matrix:
+        arch:
+          - esp32
+          - esp32s3
+          - esp32c3
+          - esp32c6
+          - nrf52840
+          - rp2040
+          - rp2350
+          - stm32
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    needs: [release-artifacts, version]
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Setup Python
+        uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+
+      - uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./output
+
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Device scripts permissions
+        run: |
+          chmod +x ./output/device-install.sh || true
+          chmod +x ./output/device-update.sh || true
+
+      - name: Zip firmware
+        run: zip -j -9 -r ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./output
+
+      - uses: actions/download-artifact@v8
+        with:
+          name: debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./elfs
+
+      - name: Zip debug elfs
+        run: zip -j -9 -r ./debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip ./elfs
+
+      # For diagnostics
+      - name: Display structure of downloaded files
+        run: ls -lR
+
+      - name: Add bins and debug elfs to GitHub Release
+        # Only run when targeting master branch with workflow_dispatch
+        if: ${{ github.ref_name == 'master' }}
+        run: |
+          gh release upload v${{ needs.version.outputs.long }} ./firmware-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip
+          gh release upload v${{ needs.version.outputs.long }} ./debug-elfs-${{matrix.arch}}-${{ needs.version.outputs.long }}.zip
+        env:
+          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
+
+  publish-firmware:
+    runs-on: ubuntu-24.04
+    if: ${{ github.event_name == 'workflow_dispatch' }}
+    needs: [release-firmware, version]
+    env:
+      targets: |-
+        esp32,esp32s3,esp32c3,esp32c6,nrf52840,rp2040,rp2350,stm32
+    steps:
+      - name: Checkout
+        uses: actions/checkout@v6
+
+      - name: Setup Python
+        uses: actions/setup-python@v6
+        with:
+          python-version: 3.x
+
+      - uses: actions/download-artifact@v8
+        with:
+          pattern: firmware-{${{ env.targets }}}-${{ needs.version.outputs.long }}
+          merge-multiple: true
+          path: ./publish
+
+      - name: Publish firmware to meshtastic.github.io
+        uses: peaceiris/actions-gh-pages@v4
+        env:
+          # On event/* branches, use the event name as the destination prefix
+          DEST_PREFIX: ${{ contains(github.ref_name, 'event/') && format('{0}/', github.ref_name) || '' }}
+        with:
+          deploy_key: ${{ secrets.DIST_PAGES_DEPLOY_KEY }}
+          external_repository: meshtastic/meshtastic.github.io
+          publish_branch: master
+          publish_dir: ./publish
+          destination_dir: ${{ env.DEST_PREFIX }}firmware-${{ needs.version.outputs.long }}
+          keep_files: true
+          user_name: github-actions[bot]
+          user_email: github-actions[bot]@users.noreply.github.com
+          commit_message: ${{ needs.version.outputs.long }}
+          enable_jekyll: true

.github/workflows/models_issue_triage.yml

@@ -38,7 +38,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
         with:
@@ -80,7 +80,7 @@ jobs:
       # ─────────────────────────────────────────────────────────────────────────
       - name: Determine if completeness check should be skipped
         if: steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: check-skip
         with:
           script: |
@@ -134,7 +134,7 @@ jobs:
 
       - name: Process analysis result
         if: (steps.quality.outputs.response == 'ok' || steps.quality.outputs.response == '') && steps.check-skip.outputs.should_skip != 'true' && steps.analysis.outputs.response != ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: process
         env:
           AI_RESPONSE: ${{ steps.analysis.outputs.response }}
@@ -174,7 +174,7 @@ jobs:
 
       - name: Apply triage label
         if: steps.process.outputs.label != '' && steps.process.outputs.label != 'none'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           LABEL_NAME: ${{ steps.process.outputs.label }}
         with:
@@ -200,7 +200,7 @@ jobs:
 
       - name: Comment on issue
         if: steps.process.outputs.should_comment == 'true'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           COMMENT_BODY: ${{ steps.process.outputs.comment_body }}
         with:

.github/workflows/models_pr_triage.yml

@@ -22,7 +22,7 @@ jobs:
       # Step 1: Check if PR already has automation/type labels (skip if so)
       # ─────────────────────────────────────────────────────────────────────────
       - name: Check existing labels
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: check-labels
         with:
           script: |
@@ -58,7 +58,7 @@ jobs:
 
       - name: Apply quality label if needed
         if: steps.check-labels.outputs.skip_all != 'true' && steps.quality.outputs.response != '' && steps.quality.outputs.response != 'ok'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         id: quality-label
         env:
           QUALITY_LABEL: ${{ steps.quality.outputs.response }}
@@ -113,7 +113,7 @@ jobs:
 
       - name: Apply type label
         if: steps.check-labels.outputs.skip_all != 'true' && steps.check-labels.outputs.has_type_label != 'true' && steps.classify.outputs.response != ''
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         env:
           TYPE_LABEL: ${{ steps.classify.outputs.response }}
         with:

.github/workflows/package_obs.yml

@@ -18,7 +18,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:

.github/workflows/package_pio_deps.yml

@@ -16,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   pkg-pio-libdeps:
@@ -26,6 +27,8 @@ jobs:
         uses: actions/checkout@v6
         with:
           submodules: recursive
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Setup Python
         uses: actions/setup-python@v6

.github/workflows/package_ppa.yml

@@ -5,8 +5,6 @@ on:
     secrets:
       PPA_GPG_PRIVATE_KEY:
         required: true
-      PPA_SFTP_PRIVATE_KEY:
-        required: true
     inputs:
       ppa_repo:
         description: Meshtastic PPA to target
@@ -18,7 +16,8 @@ on:
         type: string
 
 permissions:
-  contents: read
+  contents: write
+  packages: write
 
 jobs:
   build-debian-src:
@@ -29,7 +28,6 @@ jobs:
       build_location: ppa
 
   package-ppa:
-    if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
     runs-on: ubuntu-24.04
     needs: build-debian-src
     steps:
@@ -38,12 +36,14 @@ jobs:
         with:
           submodules: recursive
           path: meshtasticd
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Install deps
         shell: bash
         run: |
           sudo apt-get update -y --fix-missing
-          sudo apt-get install -y dput openssh-client
+          sudo apt-get install -y dput
 
       - name: Import GPG key
         uses: crazy-max/ghaction-import-gpg@v7
@@ -68,42 +68,7 @@ jobs:
       - name: Display structure of downloaded files
         run: ls -lah
 
-      - name: Trust Launchpad's SSH key
+      - name: Publish with dput
+        if: ${{ github.event_name != 'pull_request_target' && github.event_name != 'pull_request' }}
         run: |
-          mkdir -p ~/.ssh
-          ssh-keyscan -H ppa.launchpad.net >> ~/.ssh/known_hosts
-
-      - name: Setup dput config
-        env:
-          ppa_login: meshtasticorg
-        run: |
-          sudo tee /etc/meshtastic-dput.cf >/dev/null <<EOF
-          [ppa]
-          fqdn                    = ppa.launchpad.net
-          method                  = ftp
-          incoming                = ~%(ppa)s
-          login                   = anonymous
-
-          [ssh-ppa]
-          fqdn                    = ppa.launchpad.net
-          method                  = sftp
-          incoming                = ~%(ssh-ppa)s
-          login                   = ${ppa_login}
-          EOF
-
-      - name: Import SSH key
-        uses: webfactory/ssh-agent@v0.10.0
-        with:
-          ssh-private-key: ${{ secrets.PPA_SFTP_PRIVATE_KEY }}
-        id: ssh
-
-      - name: Publish with dput (sftp)
-        timeout-minutes: 30 # dput is terrible, sometimes runs 'forever'
-        env:
-          up_ppa_repo: ${{ inputs.ppa_repo }}
-          up_series: ${{ inputs.series }}
-          up_version: ${{ steps.version.outputs.deb }}
-        run: >
-          dput -c /etc/meshtastic-dput.cf
-          ssh-${up_ppa_repo}
-          meshtasticd_${up_version}~${up_series}_source.changes
+          dput ${{ inputs.ppa_repo }} meshtasticd_${{ steps.version.outputs.deb }}~${{ inputs.series }}_source.changes

.github/workflows/pr_enforce_labels.yml

@@ -13,7 +13,7 @@ jobs:
     runs-on: ubuntu-latest
     steps:
       - name: Check for PR labels
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         with:
           script: |
             const labels = context.payload.pull_request.labels.map(label => label.name);

.github/workflows/pr_tests.yml

@@ -177,7 +177,7 @@ jobs:
 
       - name: Comment test results on PR
         if: github.event_name == 'pull_request' && needs.native-tests.result != 'skipped'
-        uses: actions/github-script@v9
+        uses: actions/github-script@v8
         with:
           script: |
             const fs = require('fs');

.github/workflows/test_native.yml

@@ -16,6 +16,8 @@ jobs:
     steps:
       - uses: actions/checkout@v6
         with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
           submodules: recursive
 
       - name: Setup native build
@@ -70,6 +72,8 @@ jobs:
     steps:
       - uses: actions/checkout@v6
         with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
           submodules: recursive
 
       - name: Setup native build
@@ -124,6 +128,9 @@ jobs:
     if: always()
     steps:
       - uses: actions/checkout@v6
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
 
       - name: Get release version string
         run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
@@ -136,7 +143,7 @@ jobs:
           merge-multiple: true
 
       - name: Test Report
-        uses: dorny/test-reporter@v3.0.0
+        uses: dorny/test-reporter@v2.6.0
         with:
           name: PlatformIO Tests
           path: testreport.xml

.github/workflows/tests.yml

@@ -52,7 +52,7 @@ jobs:
           node-version: 24
 
       - name: Setup pnpm
-        uses: pnpm/action-setup@v6
+        uses: pnpm/action-setup@v4
         with:
           version: latest
 

.github/workflows/update_protobufs.yml

@@ -6,7 +6,7 @@ permissions: read-all
 jobs:
   update-protobufs:
     runs-on: ubuntu-latest
-    permissions: # Needed for peter-evans/create-pull-request.
+    permissions:
       contents: write
       pull-requests: write
     steps:

.trunk/trunk.yaml

@@ -8,27 +8,27 @@ plugins:
       uri: https://github.com/trunk-io/plugins
 lint:
   enabled:
-    - checkov@3.2.517
-    - renovate@43.110.9
+    - checkov@3.2.508
+    - renovate@43.76.3
     - prettier@3.8.1
-    - trufflehog@3.94.3
+    - trufflehog@3.93.8
     - yamllint@1.38.0
     - bandit@1.9.4
     - trivy@0.69.3
     - taplo@0.10.0
-    - ruff@0.15.9
+    - ruff@0.15.6
     - isort@8.0.1
     - markdownlint@0.48.0
     - oxipng@10.1.0
     - svgo@4.0.1
-    - actionlint@1.7.12
+    - actionlint@1.7.11
     - flake8@7.3.0
     - hadolint@2.14.0
     - shfmt@3.6.0
     - shellcheck@0.11.0
     - black@26.3.1
     - git-diff-check
-    - gitleaks@8.30.1
+    - gitleaks@8.30.0
     - clang-format@16.0.3
   ignore:
     - linters: [ALL]

bin/config-dist.yaml

@@ -204,16 +204,6 @@ HostMetrics:
 #  UserStringCommand: cat /sys/firmware/devicetree/base/serial-number # Command to execute, to send the results as the userString
 
 
-StoreAndForward:
-#  Enabled: true # Enable Store and Forward++, true by default
-#  DBPath: /var/lib/meshtasticd/ # Path to the S&F++ Sqlite DB
-#  Stratum0: false # Specify if this node is a Stratum 0 node, the controller node.
-#  InitialSync: 10 # Number of messages to 
-#  Hops: 3 # Number of hops to use for SF++ messages
-#  AnnounceInterval: 5 # Interval in minutes between announcing tip of chain hash
-#  MaxChainLength: 1000 # Maximum number of messages to store in a chain
-
-
 Config:
 #  DisplayMode: TWOCOLOR # uncomment to force BaseUI
 #  DisplayMode: COLOR # uncomment to force MUI

bin/config.d/OpenWRT/BananaPi-BPI-R4-sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: BananaPi-BPI-R4-sx1262
-  support: community
-  compatible:
-    - bananapi_bpi-r4 # OpenWrt target
-
 Lora:
   Module: sx1262  # BananaPi-BPI-R4 SPI via 26p GPIO Header
 ##  CS: 28

bin/config.d/OpenWRT/OpenWRT-One-mikroBUS-LR-IOT-CLICK.yaml

@@ -1,10 +1,4 @@
 ##  https://www.mikroe.com/lr-iot-click
-Meta:
-  name: OpenWRT One mikroBUS LR-IOT-CLICK
-  support: community
-  compatible:
-    - openwrt_one # OpenWrt target
-
 Lora:
   Module: lr1110  # OpenWRT ONE mikroBUS with LR-IOT-CLICK
 #  CS: 25

bin/config.d/OpenWRT/OpenWRT_One_mikroBUS_sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: OpenWRT One mikroBUS sx1262
-  support: community
-  compatible:
-    - openwrt_one # OpenWrt target
-
 Lora:
   Module: sx1262
   IRQ: 10

bin/config.d/README.md

@@ -1,28 +0,0 @@
-# meshtasticd configuration files
-
-This directory contains YAML configuration files for meshtasticd. Each file describes a specific hardware configuration, including the LoRa module and pin assignments. These configurations are used by meshtasticd to correctly interface with the hardware.
-
-## Metadata structure
-
-Each configuration file includes a `Meta` section that provides information about the configuration.
-This configuration is consumed by configuration-selection tools.
-
-```yaml
-Meta:
-  name: MeshAdv-Pi E22-900M30S # A unique identifier for this configuration.
-  support: community # community, official, or deprecated; determined by Meshtastic Leads.
-  compatible: # A list of compatible products or platforms.
-    - raspberry-pi
-```
-`name`: A unique identifier for the configuration, typically reflecting the hardware it supports.
-
-`support`: Indicates the level of support for this configuration. It can be one of the following:
-
-- `community`: Supported by the Meshtastic community. Meshtastic Members may not possess, or have not tested this configuration.
-- `official`: Fully supported by Meshtastic. Meshtastic Members have tested and verified this configuration.
-- `deprecated`: No longer recommended for deployment by Meshtastic.
-
-`compatible`: A list of compatible products or platforms that can use this configuration.
-This will vary depending on the intended use case / platform.
-Multiple compatible entries can be included. E.g. Armbian `BOARD` value or OpenWrt `TARGET` value.
-These tags can be consumed by different configuration-selection tools, filtering based upon their platform/etc.

bin/config.d/display-waveshare-1-44.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare 1.44inch LCD HAT
-  support: community
-  compatible:
-    - raspberry-pi
-
 ### Waveshare 1.44inch LCD HAT
 Display:
   Panel: ST7735S

bin/config.d/display-waveshare-2.8.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare 2.8inch LCD HAT
-  support: community
-  compatible:
-    - raspberry-pi
-
 Display:
 
 ### Waveshare 2.8inch RPi LCD

bin/config.d/femtofox/femtofox_E80-900M2213S.yaml

@@ -1,30 +0,0 @@
----
-Lora:
-## Ebyte E80-900M22S
-## This is a bit experimental
-## 
-##
-  Module: lr1121
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO3_TCXO_VOLTAGE: 1.8
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-
-
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
-  
-rfswitch_table:
-  pins: [DIO5, DIO6, DIO7]
-  MODE_STBY: [LOW, LOW, LOW]
-  MODE_RX: [LOW, HIGH, LOW]
-  MODE_TX: [HIGH, HIGH, LOW]
-  MODE_TX_HP: [HIGH, LOW, LOW]
-  MODE_TX_HF: [LOW, LOW, LOW]
-  MODE_GNSS: [LOW, LOW, HIGH]
-  MODE_WIFI: [LOW, LOW, LOW]
-
-General:
-  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_LR1121 generic.yaml

@@ -1,46 +0,0 @@
----
-Lora:
-## Ebyte E80-900M22S
-## This is a bit experimental
-## 
-##
-  Module: lr1121
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO3_TCXO_VOLTAGE: 1.8
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-
-
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
-  
-rfswitch_table:
-  pins:
-    - DIO5
-    - DIO6
-  MODE_STBY:
-    - LOW
-    - LOW
-  MODE_RX:
-    - HIGH
-    - LOW
-  MODE_TX:
-    - HIGH
-    - HIGH
-  MODE_TX_HP:
-    - LOW
-    - HIGH
-  MODE_TX_HF:
-    - LOW
-    - LOW
-  MODE_GNSS:
-    - LOW
-    - LOW
-  MODE_WIFI:
-    - LOW
-    - LOW
-
-General:
-  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_LR1121_TCXO.yaml

@@ -1,22 +1,20 @@
----
-Meta:
-  name: Femtofox Ebyte E80-900M22S with TCXO
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E80-900M22S
-## This is a bit experimental
-## 
-##
-  Module: lr1121
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO3_TCXO_VOLTAGE: 1.8
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E80-900M22S
+## This is a bit experimental
+## 
+##
+  Module: lr1121
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO3_TCXO_VOLTAGE: 1.8
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+
+
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_SX1262_TCXO.yaml

@@ -1,24 +1,21 @@
----
-Meta:
-  name: Femtofox SX1262 TCXO
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E22-900M30S, E22-900M22S with or without external RF switching setup
-## HT-RA62 (Has internal switching, but whatever)
-## Seeed WIO SX1262 (already has TXEN-DIO2 link, but needs RXEN)
-## Will work with any module with or without RF switching, and with TCXO
-  Module: sx1262
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
-#  TXen: bridge to DIO2 on E22 module
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E22-900M30S, E22-900M22S with or without external RF switching setup
+## HT-RA62 (Has internal switching, but whatever)
+## Seeed WIO SX1262 (already has TXEN-DIO2 link, but needs RXEN)
+## Will work with any module with or without RF switching, and with TCXO
+  Module: sx1262
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: true
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
+#  TXen: bridge to DIO2 on E22 module
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_SX1262_XTAL.yaml

@@ -1,24 +1,21 @@
----
-Meta:
-  name: Femtofox SX1262 XTAL
-  support: community
-  compatible:
-    - luckfox-pico-mini # Armbian
-
-Lora:
-## Ebyte E22-900MM22S with no external RF switching setup
-## Waveshare SX126X XXXM, AI Thinker RA-01SH
-## Will work with any module with or without RF switching and no TCXO
-
-  Module: sx1262  
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: false
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1 
-  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
-#  TXen: bridge to DIO2 on E22 module
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
+---
+Lora:
+## Ebyte E22-900MM22S with no external RF switching setup
+## Waveshare SX126X XXXM, AI Thinker RA-01SH
+## Will work with any module with or without RF switching and no TCXO
+
+  Module: sx1262  
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO2_AS_RF_SWITCH: true
+  DIO3_TCXO_VOLTAGE: false
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1 
+  RXen: 24 #pin12 / GPIO56 1D0 # Not strictly needed for auto-switching, but why complicate things?
+#  TXen: bridge to DIO2 on E22 module
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_WIO-LR1121.yaml

@@ -1,30 +0,0 @@
----
-Lora:
-## Ebyte E80-900M22S
-## This is a bit experimental
-## 
-##
-  Module: lr1121
-  gpiochip: 1 # subtract 32 from the gpio numbers
-  DIO3_TCXO_VOLTAGE: 1.8
-  CS: 16 #pin6 / GPIO48 1C0
-  IRQ: 23  #pin17 / GPIO55 1C7
-  Busy: 22 #pin16 / GPIO54 1C6
-  Reset: 25 #pin13 / GPIO57 1D1
-
-
-  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
-  spiSpeed: 2000000
-  
-rfswitch_table:
-  pins: [DIO5, DIO6, DIO7]
-  MODE_STBY: [LOW, LOW, LOW]
-  MODE_RX: [LOW, LOW, LOW]
-  MODE_TX: [LOW, HIGH, LOW]
-  MODE_TX_HP: [HIGH, LOW, LOW]
-  # MODE_TX_HF: []
-  # MODE_GNSS: []
-  MODE_WIFI: [LOW, LOW, LOW]
-
-General:
-  MACAddressSource: eth0

bin/config.d/lora-Adafruit-RFM9x.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Adafruit RFM9x
-  support: deprecated
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: RF95  # Adafruit RFM9x
   Reset: 25

bin/config.d/lora-MeshAdv-900M30S.yaml

@@ -1,11 +1,5 @@
 # MeshAdv-Pi E22-900M30S
 # https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262
   CS: 21

bin/config.d/lora-MeshAdv-Mini-900M22S.yaml

@@ -1,11 +1,5 @@
 # MeshAdv Mini E22-900M22S
 # https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Ebyte E22-900M22S 
   CS: 8

bin/config.d/lora-RAK6421-13300-slot1.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13300 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-RAK6421-13300-slot2.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
-  ### RAK13300 in Slot 2 pins
+  ### RAK13300in Slot 2 pins
   IRQ: 18 #IO6
   Reset: 24 # IO4
   Busy: 19 # IO5

bin/config.d/lora-RAK6421-13302-slot1.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13302 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-RAK6421-13302-slot2.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
-  ### RAK13302 in Slot 2 pins
+  ### RAK13300in Slot 2 pins
   IRQ: 18 #IO6
   Reset: 24 # IO4
   Busy: 19 # IO5

bin/config.d/lora-ecb41-pge-MeshAdv-900M30S.yaml

@@ -1,39 +0,0 @@
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_A1 (physical 40)
-    pin: 1
-    gpiochip: 0
-    line: 1
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO0_B4 (physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  TXen: # GPIO1_D1 (physical 33)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  RXen: # GPIO1_B3 (physical 32)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-MeshAdv-Mini-900M22S.yaml

@@ -1,33 +0,0 @@
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_B6 (physical 24, SPI1_CSN0)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO1_C3 (physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  RXen: # GPIO1_B3 (physical 32)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot1.yaml

@@ -1,38 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6, physical 15)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO0_A3 (IO4, physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO1_C3 (IO5, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 43 # GPIO1_B3 (physical 32)
-      gpiochip: 1
-      line: 11
-    - pin: 57 # GPIO1_D1 (physical 33)
-      gpiochip: 1
-      line: 25
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
-  #   pin: 14
-  #   gpiochip: 0
-  #   line: 14

bin/config.d/lora-ecb41-pge-RAK6421-13300-slot2.yaml

@@ -1,36 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B4 (IO6, physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Reset: # GPIO1_C3 (IO4, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  Busy: # GPIO0_B3 (IO5, physical 35)
-    pin: 11
-    gpiochip: 0
-    line: 11
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 37)
-      gpiochip: 0
-      line: 2
-    - pin: 50 # GPIO1_C2 (physical 16)
-      gpiochip: 1
-      line: 18
-  spidev: spidev0.1
-  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
-  #   pin: 7
-  #   gpiochip: 0
-  #   line: 7

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot1.yaml

@@ -1,39 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6, physical 15)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO0_A3 (IO4, physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO1_C3 (IO5, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 43 # GPIO1_B3 (physical 32)
-      gpiochip: 1
-      line: 11
-    - pin: 57 # GPIO1_D1 (physical 33)
-      gpiochip: 1
-      line: 25
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B6 (SPI1_CSN0, physical 24)
-  #   pin: 14
-  #   gpiochip: 0
-  #   line: 14
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-RAK6421-13302-slot2.yaml

@@ -1,37 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B4 (IO6, physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Reset: # GPIO1_C3 (IO4, physical 18)
-    pin: 51
-    gpiochip: 1
-    line: 19
-  Busy: # GPIO0_B3 (IO5, physical 35)
-    pin: 11
-    gpiochip: 0
-    line: 11
-  # Ant_sw: # GPIO1_C2 (IO3, physical 16)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 37)
-      gpiochip: 0
-      line: 2
-    - pin: 50 # GPIO1_C2 (physical 16)
-      gpiochip: 1
-      line: 18
-  spidev: spidev0.1
-  # CS: # GPIO0_A7 (SPI1_CSN1, physical 26)
-  #   pin: 7
-  #   gpiochip: 0
-  #   line: 7
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ecb41-pge-waveshare-sxxx.yaml

@@ -1,30 +0,0 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - ebyte-ecb41-pge # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_A1 (physical 40)
-    pin: 1
-    gpiochip: 0
-    line: 1
-  IRQ: # GPIO0_A3 (physical 36)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  Busy: # GPIO0_A0 (physical 38)
-    pin: 0
-    gpiochip: 0
-    line: 0
-  Reset: # GPIO0_B4 (physical 12)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  SX126X_ANT_SW: # GPIO1_B2 (physical 31)
-    pin: 42
-    gpiochip: 1
-    line: 10
-  spidev: spidev0.0

bin/config.d/lora-hat-rak-6421-pi-hat.yaml

@@ -1,12 +1,6 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1 (Autoconf default)
-  support: official
-  compatible:
-    - raspberry-pi
-
 Lora:
 
-  ### RAK13300 in Slot 1
+  ### RAK13300in Slot 1
   Module: sx1262
   IRQ: 22 #IO6
   Reset: 16 # IO4

bin/config.d/lora-lyra-picocalc-wio-sx1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Luckfox Lyra PicoCalc Wio LoRa SX1262
-  support: official
-  compatible:
-    - luckfox-lyra-plus # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ultra_1w.yaml

@@ -2,13 +2,6 @@
 # Enable overlay 'luckfox-lyra-ultra-w-spi0-cs0-spidev' with armbian-config
 # https://github.com/wehooper4/Meshtastic-Hardware/tree/main/Luckfox%20Ultra%20Hat
 # 1 Watt Lyra Ultra hat
-Meta:
-  name: wehooper4 Luckfox Ultra 1W
-  support: community
-  compatible:
-    - luckfox-pico-ultra # Armbian
-    - luckfox-lyra-ultra # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ultra_2w.yaml

@@ -2,13 +2,6 @@
 # Enable overlay 'luckfox-lyra-ultra-w-spi0-cs0-spidev' with armbian-config
 # https://github.com/wehooper4/Meshtastic-Hardware/tree/main/Luckfox%20Ultra%20Hat
 # 2 Watt Lyra Ultra hat
-Meta:
-  name: wehooper4 Luckfox Ultra 2W
-  support: community
-  compatible:
-    - luckfox-pico-ultra # Armbian
-    - luckfox-lyra-ultra # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-ws-raspberry-pi-pico-hat.yaml

@@ -2,12 +2,6 @@
 # Enable overlay 'luckfox-lyra-plus-spi0-cs0_rmio13-spidev' with armbian-config
 # Waveshare LoRa HAT for Raspberry Pi Pico
 # https://www.waveshare.com/wiki/Pico-LoRa-SX1262
-Meta:
-  name: Waveshare LoRa HAT for Raspberry Pi Pico
-  support: community
-  compatible:
-    - luckfox-lyra-plus # Armbian
-
 Lora:
   Module: sx1262
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-lyra-zero-MeshAdv-900M30S.yaml

@@ -1,39 +0,0 @@
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_C2 (physical 40)
-    pin: 18
-    gpiochip: 0
-    line: 18
-  IRQ: # GPIO1_D1 (physical 36)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1 (physical 38)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  TXen: # GPIO1_C2 (physical 33)
-    pin: 50
-    gpiochip: 1
-    line: 18
-  RXen: # GPIO1_D2 (physical 32)
-    pin: 58
-    gpiochip: 1
-    line: 26
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-lyra-zero-MeshAdv-Mini-900M22S.yaml

@@ -1,33 +0,0 @@
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_B2_d (phys 24, RPi CE0)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  IRQ: # GPIO1_D1_d (phys 36, RPi GPIO16)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1_d (phys 38, RPi GPIO20)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B4_d (phys 18, RPi GPIO24)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  RXen: # GPIO1_D2_d (phys 32, RPi GPIO12)
-    pin: 58
-    gpiochip: 1
-    line: 26
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-lyra-zero-RAK6421-13300-slot1.yaml

@@ -1,38 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO1_D1 (IO4)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_B4 (IO5)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  # Ant_sw: # GPIO1_C2 (IO3)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 58 # GPIO1_D2
-      gpiochip: 1
-      line: 26
-    - pin: 50 # GPIO1_C2
-      gpiochip: 1
-      line: 18
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B2
-  #   pin: 10
-  #   gpiochip: 0
-  #   line: 10

bin/config.d/lora-lyra-zero-RAK6421-13300-slot2.yaml

@@ -1,36 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO0_B4 (IO4)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Busy: # GPIO1_C0 (IO5)
-    pin: 48
-    gpiochip: 1
-    line: 16
-  # Ant_sw: # GPIO0_B5 (IO3)
-  #   pin: 13
-  #   gpiochip: 0
-  #   line: 13
-  Enable_Pins:
-    - pin: 51 # GPIO1_C3
-      gpiochip: 1
-      line: 19
-    - pin: 13 # GPIO0_B5
-      gpiochip: 0
-      line: 13
-  spidev: spidev0.1
-  # CS: # GPIO0_B1
-  #   pin: 9
-  #   gpiochip: 0
-  #   line: 9

bin/config.d/lora-lyra-zero-RAK6421-13302-slot1.yaml

@@ -1,39 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_A5 (IO6)
-    pin: 5
-    gpiochip: 0
-    line: 5
-  Reset: # GPIO1_D1 (IO4)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_B4 (IO5)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  # Ant_sw: # GPIO1_C2 (IO3)
-  #   pin: 50
-  #   gpiochip: 1
-  #   line: 18
-  Enable_Pins:
-    - pin: 58 # GPIO1_D2
-      gpiochip: 1
-      line: 26
-    - pin: 50 # GPIO1_C2
-      gpiochip: 1
-      line: 18
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_B2
-  #   pin: 10
-  #   gpiochip: 0
-  #   line: 10
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-lyra-zero-RAK6421-13302-slot2.yaml

@@ -1,37 +0,0 @@
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO0_B4 (IO4)
-    pin: 12
-    gpiochip: 0
-    line: 12
-  Busy: # GPIO1_C0 (IO5)
-    pin: 48
-    gpiochip: 1
-    line: 16
-  # Ant_sw: # GPIO0_B5 (IO3)
-  #   pin: 13
-  #   gpiochip: 0
-  #   line: 13
-  Enable_Pins:
-    - pin: 51 # GPIO1_C3
-      gpiochip: 1
-      line: 19
-    - pin: 13 # GPIO0_B5
-      gpiochip: 0
-      line: 13
-  spidev: spidev0.1
-  # CS: # GPIO0_B1
-  #   pin: 9
-  #   gpiochip: 0
-  #   line: 9
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-lyra-zero-waveshare-sxxx.yaml

@@ -1,30 +0,0 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - luckfox-lyra-zero-w # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_C2 (physical 40)
-    pin: 18
-    gpiochip: 0
-    line: 18
-  IRQ: # GPIO1_D1 (physical 36)
-    pin: 57
-    gpiochip: 1
-    line: 25
-  Busy: # GPIO0_C1 (physical 38)
-    pin: 17
-    gpiochip: 0
-    line: 17
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  SX126X_ANT_SW: # GPIO1_B3 (physical 31)
-    pin: 43
-    gpiochip: 1
-    line: 11
-  spidev: spidev0.0

bin/config.d/lora-meshstick-1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Lora Meshstick SX1262
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-ok3506-MeshAdv-900M30S.yaml

@@ -1,41 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
-Meta:
-  name: MeshAdv-Pi E22-900M30S
-  support: community
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  CS: # GPIO0_B0 (physical 40)
-    pin: 8
-    gpiochip: 0
-    line: 8
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  TXen: # GPIO0_A3 (physical 33)
-    pin: 3
-    gpiochip: 0
-    line: 3
-  RXen: # GPIO0_A2 (physical 32)
-    pin: 2
-    gpiochip: 0
-    line: 2
-  DIO3_TCXO_VOLTAGE: true
-  # Only for E22-900M33S:
-  # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
-  spidev: spidev0.0

bin/config.d/lora-ok3506-MeshAdv-Mini-900M22S.yaml

@@ -1,35 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Meta:
-  name: MeshAdv Mini E22-900M22S
-  support: community
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262 # Ebyte E22-900M22S
-  CS: # GPIO0_C3 (physical 24, SPI0_CSN0)
-    pin: 19
-    gpiochip: 0
-    line: 19
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO3_A6 (physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  RXen: # GPIO0_A2 (physical 32)
-    pin: 2
-    gpiochip: 0
-    line: 2
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: spidev0.0

bin/config.d/lora-ok3506-RAK6421-13300-slot1.yaml

@@ -1,40 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13300 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO3_B5 (IO6, physical 15)
-    pin: 109
-    gpiochip: 3
-    line: 13
-  Reset: # GPIO3_B0 (IO4, physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO3_A6 (IO5, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
-  #   pin: 3
-  #   gpiochip: 0
-  #   line: 3
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 32)
-      gpiochip: 0
-      line: 2
-    - pin: 3 # GPIO0_A3 (physical 33)
-      gpiochip: 0
-      line: 3
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
-  #   pin: 19
-  #   gpiochip: 0
-  #   line: 19

bin/config.d/lora-ok3506-RAK6421-13300-slot2.yaml

@@ -1,38 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13300 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6, physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO3_A6 (IO4, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  Busy: # GPIO0_B2 (IO5, physical 35)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
-  #   pin: 103
-  #   gpiochip: 3
-  #   line: 7
-  Enable_Pins:
-    - pin: 106 # GPIO3_B2 (physical 37)
-      gpiochip: 3
-      line: 10
-    - pin: 103 # GPIO3_A7 (physical 16)
-      gpiochip: 3
-      line: 7
-  spidev: spidev0.1
-  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
-  #   pin: 15
-  #   gpiochip: 0
-  #   line: 15

bin/config.d/lora-ok3506-RAK6421-13302-slot1.yaml

@@ -1,41 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13302 Slot 1
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO3_B5 (IO6, physical 15)
-    pin: 109
-    gpiochip: 3
-    line: 13
-  Reset: # GPIO3_B0 (IO4, physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO3_A6 (IO5, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  # Ant_sw: # GPIO0_A3 (IO3, physical 33)
-  #   pin: 3
-  #   gpiochip: 0
-  #   line: 3
-  Enable_Pins:
-    - pin: 2 # GPIO0_A2 (physical 32)
-      gpiochip: 0
-      line: 2
-    - pin: 3 # GPIO0_A3 (physical 33)
-      gpiochip: 0
-      line: 3
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: # GPIO0_C3 (SPI0_CSN0, physical 24)
-  #   pin: 19
-  #   gpiochip: 0
-  #   line: 19
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-RAK6421-13302-slot2.yaml

@@ -1,39 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: RAK6421 + RAK13302 Slot 2
-  support: community # Promote when tested
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262
-  IRQ: # GPIO0_B6 (IO6, physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  Reset: # GPIO3_A6 (IO4, physical 18)
-    pin: 102
-    gpiochip: 3
-    line: 6
-  Busy: # GPIO0_B2 (IO5, physical 35)
-    pin: 10
-    gpiochip: 0
-    line: 10
-  # Ant_sw: # GPIO3_A7 (IO3, physical 16)
-  #   pin: 103
-  #   gpiochip: 3
-  #   line: 7
-  Enable_Pins:
-    - pin: 106 # GPIO3_B2 (physical 37)
-      gpiochip: 3
-      line: 10
-    - pin: 103 # GPIO3_A7 (physical 16)
-      gpiochip: 3
-      line: 7
-  spidev: spidev0.1
-  # CS: # GPIO0_B7 (SPI0_CSN1, physical 26)
-  #   pin: 15
-  #   gpiochip: 0
-  #   line: 15
-  TX_GAIN_LORA: [9, 9, 10, 11, 9, 8, 9, 10, 10, 10, 11, 12, 12, 12, 12, 12, 12, 12, 12, 10, 9, 8]

bin/config.d/lora-ok3506-waveshare-sxxx.yaml

@@ -1,32 +0,0 @@
-# !! WARNING: Hats on the OK3506 board are installed "backwards" (facing outwards)
-
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - forlinx-ok3506-s12 # Armbian
-
-Lora:
-  Module: sx1262  # Waveshare SX126X XXXM
-  DIO2_AS_RF_SWITCH: true
-  CS: # GPIO0_B0 (physical 40)
-    pin: 8
-    gpiochip: 0
-    line: 8
-  IRQ: # GPIO3_B0 (physical 36)
-    pin: 104
-    gpiochip: 3
-    line: 8
-  Busy: # GPIO0_B1 (physical 38)
-    pin: 9
-    gpiochip: 0
-    line: 9
-  Reset: # GPIO0_B6 (physical 12)
-    pin: 14
-    gpiochip: 0
-    line: 14
-  SX126X_ANT_SW: # GPIO3_B3 (physical 31)
-    pin: 107
-    gpiochip: 3
-    line: 11
-  spidev: spidev0.0

bin/config.d/lora-piggystick-lr1121.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Lora Meshstick SX1262
-  support: community
-  compatible:
-    - usb
-
 Lora:
   Module: lr1121
   CS: 0

bin/config.d/lora-pinedio-usb-sx1262.yaml

@@ -1,11 +1,5 @@
-Meta:
-  name: Pinedio USB SX1262
-  support: deprecated
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0 
   IRQ: 10
-  spidev: ch341
+  spidev: ch341

bin/config.d/lora-raxda-rock2f-starter-edition-hat.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: raxda-rock2f-starter-edition-hat
-  support: community
-  compatible:
-    - rock-2f # Armbian
-
 Lora:
 
 ### Raxda Rock 2F running Armbian Linux 6.1.99-vendor-rk35xx

bin/config.d/lora-starter-edition-sx1262-i2c.yaml

@@ -1,11 +1,5 @@
 # https://www.waveshare.com/core1262-868m.htm
 # https://github.com/markbirss/lora-starter-edition-sx1262-i2c
-Meta:
-  name: lora-starter-edition-sx1262-i2c
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Starter Edition SX1262 I2C Raspberry Pi HAT
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-usb-meshstick-1262.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: meshstick-1262
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-meshtoad-e22.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: meshtoad-e22
-  support: official
-  compatible:
-    - usb
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-umesh-1262-30dbm.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: umesh-1262-30dbm
-  support: community
-  compatible:
-    - clockwork-uconsole
-
 Lora:
   Module: sx1262
   CS: 0

bin/config.d/lora-usb-umesh-1268-30dbm.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: umesh-1268-30dbm
-  support: community
-  compatible:
-    - clockwork-uconsole
-
 Lora:
   Module: sx1268
   CS: 0

bin/config.d/lora-waveshare-sxxx.yaml

@@ -1,9 +1,3 @@
-Meta:
-  name: Waveshare SX1262
-  support: deprecated
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Waveshare SX126X XXXM
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-ws-raspberry-pi-pico-to-rpi-adapter.yaml

@@ -1,12 +1,5 @@
 # https://www.waveshare.com/pico-lora-sx1262-868m.htm
 # https://github.com/markbirss/lora-ws-raspberry-pi-pico-to-rpi-adapter
-
-Meta:
-  name: ws-raspberry-pico-to-rpi-adapter
-  support: community
-  compatible:
-    - raspberry-pi
-
 Lora:
   Module: sx1262  # Waveshare Raspberry Pi Pico to Raspberry Pi HAT Adapter
   DIO2_AS_RF_SWITCH: true

bin/config.d/lora-ws-raspberry-pico-to-orangepi-03.yaml

@@ -15,12 +15,6 @@
 #   5     CS          24
 #   26    DIO1/IRQ    26
 
-Meta:
-  name: ws-raspberry-pico-to-orangepi-03
-  support: community
-  compatible:
-    - orange-pi-zero-3 # Armbian
-
 Lora:
   Module: sx1262  # Waveshare Raspberry Pico Lora module
   DIO2_AS_RF_SWITCH: true

bin/generate_ci_matrix.py

@@ -43,7 +43,7 @@ for pio_env in pio_envs:
   env = {
     "ci": {"board": pio_env, "platform": env_platform},
     "board_level": cfg.get(f"env:{pio_env}", "board_level", default=None),
-    "board_check": cfg.get(f"env:{pio_env}", "board_check", default="false").strip().lower() == "true",
+    "board_check": bool(cfg.get(f"env:{pio_env}", "board_check", default=False)),
   }
   all_envs.append(env)
 

bin/org.meshtastic.meshtasticd.metainfo.xml

@@ -87,9 +87,6 @@
   </screenshots>
 
   <releases>
-    <release version="2.7.22" date="2026-04-06">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.22</url>
-    </release>
     <release version="2.7.21" date="2026-03-11">
       <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.21</url>
     </release>

boards/t5-epaper-s3.json

@@ -1,38 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32s3_out.ld",
-      "memory_type": "qio_opi",
-      "partitions": "default_16MB.csv"
-    },
-    "core": "esp32",
-    "extra_flags": [
-      "-DBOARD_HAS_PSRAM",
-      "-DARDUINO_RUNNING_CORE=1",
-      "-DARDUINO_EVENT_RUNNING_CORE=0",
-      "-DARDUINO_USB_CDC_ON_BOOT=1",
-      "-DARDUINO_USB_MODE=1"
-    ],
-    "f_cpu": "240000000L",
-    "f_flash": "80000000L",
-    "flash_mode": "qio",
-    "hwids": [["0x303A", "0x1001"]],
-    "mcu": "esp32s3",
-    "variant": "esp32s3"
-  },
-  "connectivity": ["wifi", "bluetooth", "lora"],
-  "debug": {
-    "openocd_target": "esp32s3.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "LilyGo T5-ePaper-S3",
-  "upload": {
-    "flash_size": "16MB",
-    "maximum_ram_size": 327680,
-    "maximum_size": 16777216,
-    "require_upload_port": true,
-    "speed": 921600
-  },
-  "url": "https://lilygo.cc/products/t5-e-paper-s3-pro",
-  "vendor": "LILYGO"
-}

boards/tracker-t2000-c.json

@@ -1,30 +1,30 @@
 {
   "build": {
     "arduino": {
-      "ldscript": "nrf52840_s140_v6.ld"
+      "ldscript": "nrf52840_s140_v7.ld"
     },
     "core": "nRF5",
     "cpu": "cortex-m4",
-    "extra_flags": "-DNRF52840_XXAA",
+    "extra_flags": "-DARDUINO_TRACKER_T2000_C -DNRF52840_XXAA",
     "f_cpu": "64000000L",
     "hwids": [
-      ["0x239A", "0x4405"],
+      ["0x239A", "0x8029"],
       ["0x239A", "0x0029"],
       ["0x239A", "0x002A"],
-      ["0x2886", "0x1667"]
+      ["0x239A", "0x802A"],
+      ["0x2886", "0x0057"]
     ],
-    "usb_product": "HT-n5262G",
+    "usb_product": "T2000-BOOT",
     "mcu": "nrf52840",
-    "variant": "heltec_mesh_node_t096",
-    "variants_dir": "variants",
+    "variant": "Seeed_T2000-C",
     "bsp": {
       "name": "adafruit"
     },
     "softdevice": {
       "sd_flags": "-DS140",
       "sd_name": "s140",
-      "sd_version": "6.1.1",
-      "sd_fwid": "0x00B6"
+      "sd_version": "7.3.0",
+      "sd_fwid": "0x0123"
     },
     "bootloader": {
       "settings_addr": "0xFF000"
@@ -33,22 +33,28 @@
   "connectivity": ["bluetooth"],
   "debug": {
     "jlink_device": "nRF52840_xxAA",
-    "onboard_tools": ["jlink"],
     "svd_path": "nrf52840.svd",
     "openocd_target": "nrf52840-mdk-rs"
   },
   "frameworks": ["arduino"],
-  "name": "Heltec nrf (Adafruit BSP)",
+  "name": "Seeed T2000-C",
   "upload": {
     "maximum_ram_size": 248832,
     "maximum_size": 815104,
     "speed": 115200,
     "protocol": "nrfutil",
-    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
+    "protocols": [
+      "jlink",
+      "nrfjprog",
+      "nrfutil",
+      "stlink",
+      "cmsis-dap",
+      "blackmagic"
+    ],
     "use_1200bps_touch": true,
     "require_upload_port": true,
     "wait_for_upload_port": true
   },
-  "url": "https://heltec.org/",
-  "vendor": "Heltec"
+  "url": "https://www.seeedstudio.com/",
+  "vendor": "Seeed Studio"
 }

boards/ttgo-tbeam.json

@@ -1,29 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32_out.ld"
-    },
-    "core": "esp32",
-    "extra_flags": "-DARDUINO_T_Beam",
-    "f_cpu": "240000000L",
-    "f_flash": "40000000L",
-    "flash_mode": "dio",
-    "mcu": "esp32",
-    "variant": "tbeam"
-  },
-  "connectivity": ["wifi", "bluetooth", "can", "ethernet"],
-  "debug": {
-    "openocd_board": "esp-wroom-32.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "TTGO T-Beam (PSRAM Disabled)",
-  "upload": {
-    "flash_size": "4MB",
-    "maximum_ram_size": 1310720,
-    "maximum_size": 4194304,
-    "require_upload_port": true,
-    "speed": 460800
-  },
-  "url": "https://github.com/LilyGO/TTGO-T-Beam",
-  "vendor": "TTGO"
-}

debian/changelog

@@ -1,9 +1,3 @@
-meshtasticd (2.7.22.0) unstable; urgency=medium
-
-  * Version 2.7.22
-
- -- GitHub Actions <github-actions[bot]@users.noreply.github.com>  Mon, 06 Apr 2026 11:34:12 +0000
-
 meshtasticd (2.7.21.0) unstable; urgency=medium
 
   * Version 2.7.21

debian/ci_pack_sdeb.sh

@@ -27,10 +27,5 @@ rm -rf debian/changelog
 dch --create --distribution "$SERIES" --package "$package" --newversion "$PKG_VERSION~$SERIES" \
 	"GitHub Actions Automatic packaging for $PKG_VERSION~$SERIES"
 
-if [[ -n $GPG_KEY_ID ]]; then
-	# Build and sign the source deb
-	debuild -S -nc -k"$GPG_KEY_ID"
-else
-	# Build the source deb without signing (forks)
-	debuild -S -nc
-fi
+# Build the source deb
+debuild -S -nc -k"$GPG_KEY_ID"

platformio.ini

@@ -77,10 +77,10 @@ lib_deps =
 	https://github.com/meshtastic/TinyGPSPlus/archive/71a82db35f3b973440044c476d4bcdc673b104f4.zip
 	# renovate: datasource=git-refs depName=meshtastic-ArduinoThread packageName=https://github.com/meshtastic/ArduinoThread gitBranch=master
 	https://github.com/meshtastic/ArduinoThread/archive/b841b0415721f1341ea41cccfb4adccfaf951567.zip
-	# renovate: datasource=github-tags depName=Nanopb packageName=nanopb/nanopb
-	https://github.com/nanopb/nanopb/archive/refs/tags/nanopb-0.4.9.1.zip
-	# renovate: datasource=github-tags depName=ErriezCRC32 packageName=Erriez/ErriezCRC32
-	https://github.com/Erriez/ErriezCRC32/archive/refs/tags/1.0.1.zip
+	# renovate: datasource=custom.pio depName=Nanopb packageName=nanopb/library/Nanopb
+	nanopb/Nanopb@0.4.91
+	# renovate: datasource=custom.pio depName=ErriezCRC32 packageName=erriez/library/ErriezCRC32
+	erriez/ErriezCRC32@1.0.1
 
 ; Used for the code analysis in PIO Home / Inspect
 check_tool = cppcheck
@@ -95,153 +95,143 @@ check_flags =
 framework = arduino
 lib_deps =
 	${env.lib_deps}
-	# renovate: datasource=github-tags depName=NonBlockingRTTTL packageName=end2endzone/NonBlockingRTTTL
-	https://github.com/end2endzone/NonBlockingRTTTL/archive/refs/tags/1.4.0.zip
+	# renovate: datasource=custom.pio depName=NonBlockingRTTTL packageName=end2endzone/library/NonBlockingRTTTL
+	end2endzone/NonBlockingRTTTL@1.4.0
 build_unflags =
 	-std=c++11
 	-std=gnu++11
 build_flags = ${env.build_flags} -Os
 	-std=gnu++17
-build_src_filter = ${env.build_src_filter} -<platform/portduino/> -<graphics/niche/> -<modules/Native/>
+build_src_filter = ${env.build_src_filter} -<platform/portduino/> -<graphics/niche/>
 
 ; Common libs for communicating over TCP/IP networks such as MQTT
 [networking_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=TBPubSubClient packageName=thingsboard/pubsubclient
-	https://github.com/thingsboard/pubsubclient/archive/refs/tags/v2.12.1.zip
-	# renovate: datasource=github-tags depName=NTPClient packageName=arduino-libraries/NTPClient
-	https://github.com/arduino-libraries/NTPClient/archive/refs/tags/3.2.1.zip
+	# renovate: datasource=custom.pio depName=TBPubSubClient packageName=thingsboard/library/TBPubSubClient
+	thingsboard/TBPubSubClient@2.12.1
+	# renovate: datasource=custom.pio depName=NTPClient packageName=arduino-libraries/library/NTPClient
+	arduino-libraries/NTPClient@3.2.1
 
 ; Extra TCP/IP networking libs for supported devices
 [networking_extra]
 lib_deps =
-	# renovate: datasource=github-tags depName=Syslog packageName=arcao/Syslog
-	https://github.com/arcao/Syslog/archive/refs/tags/v2.0.zip
+	# renovate: datasource=custom.pio depName=Syslog packageName=arcao/library/Syslog
+	arcao/Syslog@2.0.0
 
 [radiolib_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=RadioLib packageName=jgromes/RadioLib
-	https://github.com/jgromes/RadioLib/archive/refs/tags/7.6.0.zip
+	# renovate: datasource=custom.pio depName=RadioLib packageName=jgromes/library/RadioLib
+	jgromes/RadioLib@7.6.0
 
 [device-ui_base]
 lib_deps =
 	# renovate: datasource=git-refs depName=meshtastic/device-ui packageName=https://github.com/meshtastic/device-ui gitBranch=master
-	https://github.com/meshtastic/device-ui/archive/1897dd17fceb1f101bb1a3245680aa3439edcfdd.zip
+	https://github.com/meshtastic/device-ui/archive/622b034d8791153de9d16a473723cb8625d35839.zip
 
 ; Common libs for environmental measurements in telemetry module
 [environmental_base]
 lib_deps =
-	# renovate: datasource=github-tags depName=Adafruit BusIO packageName=adafruit/Adafruit_BusIO
-	https://github.com/adafruit/Adafruit_BusIO/archive/refs/tags/1.17.4.zip
-	# renovate: datasource=github-tags depName=Adafruit Unified Sensor packageName=adafruit/Adafruit_Sensor
-	https://github.com/adafruit/Adafruit_Sensor/archive/refs/tags/1.1.15.zip
-	# renovate: datasource=github-tags depName=Adafruit GFX packageName=adafruit/Adafruit-GFX-Library
-	https://github.com/adafruit/Adafruit-GFX-Library/archive/refs/tags/1.12.6.zip
-	# renovate: datasource=github-tags depName=NeoPixel packageName=adafruit/Adafruit_NeoPixel
-	https://github.com/adafruit/Adafruit_NeoPixel/archive/refs/tags/1.15.4.zip
-	# renovate: datasource=github-tags depName=Adafruit SSD1306 packageName=adafruit/Adafruit_SSD1306
-	https://github.com/adafruit/Adafruit_SSD1306/archive/refs/tags/2.5.16.zip
-	# renovate: datasource=github-tags depName=Adafruit BMP280 packageName=adafruit/Adafruit_BMP280_Library
-	https://github.com/adafruit/Adafruit_BMP280_Library/archive/refs/tags/3.0.0.zip
-	# renovate: datasource=github-tags depName=Adafruit BMP085 packageName=adafruit/Adafruit-BMP085-Library
-	https://github.com/adafruit/Adafruit-BMP085-Library/archive/refs/tags/1.2.4.zip
-	# renovate: datasource=github-tags depName=Adafruit BME280 packageName=adafruit/Adafruit_BME280_Library
-	https://github.com/adafruit/Adafruit_BME280_Library/archive/refs/tags/2.3.0.zip
-	# renovate: datasource=github-tags depName=Adafruit DPS310 packageName=adafruit/Adafruit_DPS310
-	https://github.com/adafruit/Adafruit_DPS310/archive/refs/tags/1.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SH110x packageName=adafruit/Adafruit_SH110x
-	https://github.com/adafruit/Adafruit_SH110x/archive/refs/tags/2.1.14.zip
-	# renovate: datasource=github-tags depName=Adafruit MCP9808 packageName=adafruit/Adafruit_MCP9808_Library
-	https://github.com/adafruit/Adafruit_MCP9808_Library/archive/refs/tags/2.0.2.zip
-	# renovate: datasource=github-tags depName=Adafruit INA260 packageName=adafruit/Adafruit_INA260
-	https://github.com/adafruit/Adafruit_INA260/archive/refs/tags/1.5.3.zip
-	# renovate: datasource=github-tags depName=Adafruit INA219 packageName=adafruit/Adafruit_INA219
-	https://github.com/adafruit/Adafruit_INA219/archive/refs/tags/1.2.3.zip
-	# renovate: datasource=github-tags depName=Adafruit MPU6050 packageName=adafruit/Adafruit_MPU6050
-	https://github.com/adafruit/Adafruit_MPU6050/archive/refs/tags/2.2.9.zip
-	# renovate: datasource=github-tags depName=Adafruit LIS3DH packageName=adafruit/Adafruit_LIS3DH
-	https://github.com/adafruit/Adafruit_LIS3DH/archive/refs/tags/1.3.0.zip
-	# renovate: datasource=github-tags depName=Adafruit AHTX0 packageName=adafruit/Adafruit_AHTX0
-	https://github.com/adafruit/Adafruit_AHTX0/archive/refs/tags/2.0.6.zip
-	# renovate: datasource=github-tags depName=Adafruit LSM6DS packageName=adafruit/Adafruit_LSM6DS
-	https://github.com/adafruit/Adafruit_LSM6DS/archive/refs/tags/4.7.4.zip
-	# renovate: datasource=github-tags depName=Adafruit TSL2591 packageName=adafruit/Adafruit_TSL2591_Library
-	https://github.com/adafruit/Adafruit_TSL2591_Library/archive/refs/tags/1.4.5.zip
-	# renovate: datasource=github-tags depName=EmotiBit MLX90632 packageName=emotibit/EmotiBit_MLX90632
-	https://github.com/EmotiBit/EmotiBit_MLX90632/archive/refs/tags/v1.0.8.zip
-	# renovate: datasource=github-tags depName=Adafruit MLX90614 packageName=adafruit/Adafruit_MLX90614
-	https://github.com/adafruit/Adafruit-MLX90614-Library/archive/refs/tags/2.1.6.zip
+	# renovate: datasource=custom.pio depName=Adafruit BusIO packageName=adafruit/library/Adafruit BusIO
+	adafruit/Adafruit BusIO@1.17.4
+	# renovate: datasource=custom.pio depName=Adafruit Unified Sensor packageName=adafruit/library/Adafruit Unified Sensor
+	adafruit/Adafruit Unified Sensor@1.1.15
+	# renovate: datasource=custom.pio depName=Adafruit BMP280 packageName=adafruit/library/Adafruit BMP280 Library
+	adafruit/Adafruit BMP280 Library@3.0.0
+	# renovate: datasource=custom.pio depName=Adafruit BMP085 packageName=adafruit/library/Adafruit BMP085 Library
+	adafruit/Adafruit BMP085 Library@1.2.4
+	# renovate: datasource=custom.pio depName=Adafruit BME280 packageName=adafruit/library/Adafruit BME280 Library
+	adafruit/Adafruit BME280 Library@2.3.0
+	# renovate: datasource=custom.pio depName=Adafruit DPS310 packageName=adafruit/library/Adafruit DPS310
+	adafruit/Adafruit DPS310@1.1.6
+	# renovate: datasource=custom.pio depName=Adafruit MCP9808 packageName=adafruit/library/Adafruit MCP9808 Library
+	adafruit/Adafruit MCP9808 Library@2.0.2
+	# renovate: datasource=custom.pio depName=Adafruit INA260 packageName=adafruit/library/Adafruit INA260 Library
+	adafruit/Adafruit INA260 Library@1.5.3
+	# renovate: datasource=custom.pio depName=Adafruit INA219 packageName=adafruit/library/Adafruit INA219
+	adafruit/Adafruit INA219@1.2.3
+	# renovate: datasource=custom.pio depName=Adafruit MPU6050 packageName=adafruit/library/Adafruit MPU6050
+	adafruit/Adafruit MPU6050@2.2.9
+	# renovate: datasource=custom.pio depName=Adafruit LIS3DH packageName=adafruit/library/Adafruit LIS3DH
+	adafruit/Adafruit LIS3DH@1.3.0
+	# renovate: datasource=custom.pio depName=Adafruit AHTX0 packageName=adafruit/library/Adafruit AHTX0
+	adafruit/Adafruit AHTX0@2.0.6
+	# renovate: datasource=custom.pio depName=Adafruit LSM6DS packageName=adafruit/library/Adafruit LSM6DS
+	adafruit/Adafruit LSM6DS@4.7.4
+	# renovate: datasource=custom.pio depName=Adafruit TSL2591 packageName=adafruit/library/Adafruit TSL2591 Library
+	adafruit/Adafruit TSL2591 Library@1.4.5
+	# renovate: datasource=custom.pio depName=EmotiBit MLX90632 packageName=emotibit/library/EmotiBit MLX90632
+	emotibit/EmotiBit MLX90632@1.0.8
+	# renovate: datasource=custom.pio depName=Adafruit MLX90614 packageName=adafruit/library/Adafruit MLX90614 Library
+	adafruit/Adafruit MLX90614 Library@2.1.6
 	# renovate: datasource=git-refs depName=INA3221 packageName=https://github.com/sgtwilko/INA3221 gitBranch=FixOverflow
 	https://github.com/sgtwilko/INA3221/archive/bb03d7e9bfcc74fc798838a54f4f99738f29fc6a.zip
-	# renovate: datasource=github-tags depName=QMC5883L Compass packageName=mprograms/QMC5883LCompass
-	https://github.com/mprograms/QMC5883LCompass/archive/refs/tags/v1.2.3.zip
-	# renovate: datasource=github-tags depName=DFRobot_RTU packageName=dfrobot/DFRobot_RTU
-	https://github.com/DFRobot/DFRobot_RTU/archive/refs/tags/V1.0.6.zip
+	# renovate: datasource=custom.pio depName=QMC5883L Compass packageName=mprograms/library/QMC5883LCompass
+	mprograms/QMC5883LCompass@1.2.3
+	# renovate: datasource=custom.pio depName=DFRobot_RTU packageName=dfrobot/library/DFRobot_RTU
+	dfrobot/DFRobot_RTU@1.0.6
 	# renovate: datasource=git-refs depName=DFRobot_RainfallSensor packageName=https://github.com/DFRobot/DFRobot_RainfallSensor gitBranch=master
 	https://github.com/DFRobot/DFRobot_RainfallSensor/archive/38fea5e02b40a5430be6dab39a99a6f6347d667e.zip
-	# renovate: datasource=github-tags depName=INA226 packageName=robtillaart/INA226
-	https://github.com/RobTillaart/INA226/archive/refs/tags/0.6.6.zip
-	# renovate: datasource=github-tags depName=SparkFun MAX3010x packageName=sparkfun/SparkFun_MAX3010x_Sensor_Library
-	https://github.com/sparkfun/SparkFun_MAX3010x_Sensor_Library/archive/refs/tags/v1.1.2.zip
-	# renovate: datasource=github-tags depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/SparkFun_ICM-20948_ArduinoLibrary
-	https://github.com/sparkfun/SparkFun_ICM-20948_ArduinoLibrary/archive/refs/tags/v1.3.2.zip
-	# renovate: datasource=github-tags depName=Adafruit LTR390 Library packageName=adafruit/Adafruit_LTR390
-	https://github.com/adafruit/Adafruit_LTR390/archive/refs/tags/1.1.2.zip
-	# renovate: datasource=github-tags depName=Adafruit PCT2075 packageName=adafruit/Adafruit_PCT2075
-	https://github.com/adafruit/Adafruit_PCT2075/archive/refs/tags/1.0.6.zip
-	# renovate: datasource=github-tags depName=DFRobot_BMM150 packageName=dfrobot/DFRobot_BMM150
-	https://github.com/DFRobot/DFRobot_BMM150/archive/refs/tags/V1.0.0.zip
-	# renovate: datasource=github-tags depName=Adafruit_TSL2561 packageName=adafruit/Adafruit_TSL2561
-	https://github.com/adafruit/Adafruit_TSL2561/archive/refs/tags/1.1.3.zip
-	# renovate: datasource=github-tags depName=BH1750_WE packageName=wollewald/BH1750_WE
-	https://github.com/wollewald/BH1750_WE/archive/refs/tags/1.1.10.zip
+	# renovate: datasource=custom.pio depName=INA226 packageName=robtillaart/library/INA226
+	robtillaart/INA226@0.6.6
+	# renovate: datasource=custom.pio depName=SparkFun MAX3010x packageName=sparkfun/library/SparkFun MAX3010x Pulse and Proximity Sensor Library
+	sparkfun/SparkFun MAX3010x Pulse and Proximity Sensor Library@1.1.2
+	# renovate: datasource=custom.pio depName=SparkFun 9DoF IMU Breakout ICM 20948 packageName=sparkfun/library/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library
+	sparkfun/SparkFun 9DoF IMU Breakout - ICM 20948 - Arduino Library@1.3.2
+	# renovate: datasource=custom.pio depName=Adafruit LTR390 Library packageName=adafruit/library/Adafruit LTR390 Library
+	adafruit/Adafruit LTR390 Library@1.1.2
+	# renovate: datasource=custom.pio depName=Adafruit PCT2075 packageName=adafruit/library/Adafruit PCT2075
+	adafruit/Adafruit PCT2075@1.0.6
+	# renovate: datasource=custom.pio depName=DFRobot_BMM150 packageName=dfrobot/library/DFRobot_BMM150
+	dfrobot/DFRobot_BMM150@1.0.0
+	# renovate: datasource=custom.pio depName=Adafruit_TSL2561 packageName=adafruit/library/Adafruit TSL2561
+	adafruit/Adafruit TSL2561@1.1.3
+	# renovate: datasource=custom.pio depName=BH1750_WE packageName=wollewald/library/BH1750_WE
+	wollewald/BH1750_WE@1.1.10
 
 ; Common environmental sensor libraries (not included in native / portduino)
 [environmental_extra_common]
 lib_deps =
-	# renovate: datasource=github-tags depName=Adafruit BMP3XX packageName=adafruit/Adafruit_BMP3XX
-	https://github.com/adafruit/Adafruit_BMP3XX/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit MAX1704X packageName=adafruit/Adafruit_MAX1704X
-	https://github.com/adafruit/Adafruit_MAX1704X/archive/refs/tags/1.0.3.zip
-	# renovate: datasource=github-tags depName=Adafruit SHTC3 packageName=adafruit/Adafruit_SHTC3
-	https://github.com/adafruit/Adafruit_SHTC3/archive/refs/tags/1.0.2.zip
-	# renovate: datasource=github-tags depName=Adafruit LPS2X packageName=adafruit/Adafruit_LPS2X
-	https://github.com/adafruit/Adafruit_LPS2X/archive/refs/tags/2.0.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SHT31 packageName=adafruit/Adafruit_SHT31
-	https://github.com/adafruit/Adafruit_SHT31/archive/refs/tags/2.2.2.zip
-	# renovate: datasource=github-tags depName=Adafruit VEML7700 packageName=adafruit/Adafruit_VEML7700
-	https://github.com/adafruit/Adafruit_VEML7700/archive/refs/tags/2.1.6.zip
-	# renovate: datasource=github-tags depName=Adafruit SHT4x packageName=adafruit/Adafruit_SHT4X
-	https://github.com/adafruit/Adafruit_SHT4X/archive/refs/tags/1.0.5.zip
-	# renovate: datasource=github-tags depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library
-	https://github.com/sparkfun/SparkFun_Qwiic_Scale_NAU7802_Arduino_Library/archive/refs/tags/v1.0.6.zip
+	# renovate: datasource=custom.pio depName=Adafruit BMP3XX packageName=adafruit/library/Adafruit BMP3XX Library
+	adafruit/Adafruit BMP3XX Library@2.1.6
+	# renovate: datasource=custom.pio depName=Adafruit MAX1704X packageName=adafruit/library/Adafruit MAX1704X
+	adafruit/Adafruit MAX1704X@1.0.3
+	# renovate: datasource=custom.pio depName=Adafruit SHTC3 packageName=adafruit/library/Adafruit SHTC3 Library
+	adafruit/Adafruit SHTC3 Library@1.0.2
+	# renovate: datasource=custom.pio depName=Adafruit LPS2X packageName=adafruit/library/Adafruit LPS2X
+	adafruit/Adafruit LPS2X@2.0.6
+	# renovate: datasource=custom.pio depName=Adafruit SHT31 packageName=adafruit/library/Adafruit SHT31 Library
+	adafruit/Adafruit SHT31 Library@2.2.2
+	# renovate: datasource=custom.pio depName=Adafruit VEML7700 packageName=adafruit/library/Adafruit VEML7700 Library
+	adafruit/Adafruit VEML7700 Library@2.1.6
+	# renovate: datasource=custom.pio depName=Adafruit SHT4x packageName=adafruit/library/Adafruit SHT4x Library
+	adafruit/Adafruit SHT4x Library@1.0.5
+	# renovate: datasource=custom.pio depName=SparkFun Qwiic Scale NAU7802 packageName=sparkfun/library/SparkFun Qwiic Scale NAU7802 Arduino Library
+	sparkfun/SparkFun Qwiic Scale NAU7802 Arduino Library@1.0.6
 	# renovate: datasource=custom.pio depName=ClosedCube OPT3001 packageName=closedcube/library/ClosedCube OPT3001
 	closedcube/ClosedCube OPT3001@1.1.2
 	# renovate: datasource=git-refs depName=meshtastic-DFRobot_LarkWeatherStation packageName=https://github.com/meshtastic/DFRobot_LarkWeatherStation gitBranch=master
 	https://github.com/meshtastic/DFRobot_LarkWeatherStation/archive/4de3a9cadef0f6a5220a8a906cf9775b02b0040d.zip
-	# renovate: datasource=github-tags depName=Sensirion Core packageName=sensirion/arduino-core
-	https://github.com/Sensirion/arduino-core/archive/refs/tags/0.7.3.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SCD4x packageName=sensirion/arduino-i2c-scd4x
-	https://github.com/Sensirion/arduino-i2c-scd4x/archive/refs/tags/1.1.0.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SFA3x packageName=sensirion/arduino-i2c-sfa3x
-	https://github.com/Sensirion/arduino-i2c-sfa3x/archive/refs/tags/1.0.0.zip
-	# renovate: datasource=github-tags depName=Sensirion I2C SCD30 packageName=sensirion/arduino-i2c-scd30
-	https://github.com/Sensirion/arduino-i2c-scd30/archive/refs/tags/1.0.0.zip
-	# renovate: datasource=github-tags depName=arduino-sht packageName=sensirion/arduino-sht
-	https://github.com/Sensirion/arduino-sht/archive/refs/tags/v1.2.6.zip
+	# renovate: datasource=custom.pio depName=Sensirion Core packageName=sensirion/library/Sensirion Core
+	sensirion/Sensirion Core@0.7.3
+	# renovate: datasource=custom.pio depName=Sensirion I2C SCD4x packageName=sensirion/library/Sensirion I2C SCD4x
+	sensirion/Sensirion I2C SCD4x@1.1.0
+	# renovate: datasource=custom.pio depName=Sensirion I2C SFA3x packageName=sensirion/library/Sensirion I2C SFA3x
+	sensirion/Sensirion I2C SFA3x@1.0.0
+	# renovate: datasource=custom.pio depName=Sensirion I2C SCD30 packageName=sensirion/library/Sensirion I2C SCD30
+	sensirion/Sensirion I2C SCD30@1.0.0
 
 ; Environmental sensors with BSEC2 (Bosch proprietary IAQ)
 [environmental_extra]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=github-tags depName=Bosch BSEC2 packageName=boschsensortec/Bosch-BSEC2-Library
-	https://github.com/boschsensortec/Bosch-BSEC2-Library/archive/refs/tags/1.10.2610.zip
-	# renovate: datasource=github-tags depName=Bosch BME68x packageName=boschsensortec/Bosch-BME68x-Library
-	https://github.com/boschsensortec/Bosch-BME68x-Library/archive/refs/tags/v1.3.40408.zip
+	# renovate: datasource=custom.pio depName=Bosch BSEC2 packageName=boschsensortec/library/bsec2
+	boschsensortec/bsec2@1.10.2610
+	# renovate: datasource=custom.pio depName=Bosch BME68x packageName=boschsensortec/library/BME68x Sensor Library
+	boschsensortec/BME68x Sensor Library@1.3.40408
 
 ; Environmental sensors without BSEC (saves ~3.5KB DRAM for original ESP32 targets)
 [environmental_extra_no_bsec]
 lib_deps =
 	${environmental_extra_common.lib_deps}
-	# renovate: datasource=github-tags depName=Adafruit_BME680 packageName=adafruit/Adafruit_BME680
-	https://github.com/adafruit/Adafruit_BME680/archive/refs/tags/2.0.6.zip
+	# renovate: datasource=custom.pio depName=adafruit/Adafruit BME680 Library packageName=adafruit/library/Adafruit BME680
+	adafruit/Adafruit BME680 Library@^2.0.5

renovate.json

@@ -4,8 +4,6 @@
     ":dependencyDashboard",
     ":semanticCommitTypeAll(chore)",
     ":ignoreModulesAndTests",
-    ":noUnscheduledUpdates",
-    "schedule:daily",
     "group:recommended",
     "replacements:all",
     "workarounds:all"

src/DebugConfiguration.cpp

@@ -98,6 +98,7 @@ Syslog &Syslog::logMask(uint8_t priMask)
 
 void Syslog::enable()
 {
+    this->_client->begin(this->_port);
     this->_enabled = true;
 }
 
@@ -165,21 +166,14 @@ inline bool Syslog::_sendLog(uint16_t pri, const char *appName, const char *mess
     if ((pri & LOG_FACMASK) == 0)
         pri = LOG_MAKEPRI(LOG_FAC(this->_priDefault), pri);
 
-    // W5100S: acquire UDP socket on-demand to avoid permanent socket consumption
-    if (!this->_client->begin(this->_port)) {
-        return false;
-    }
-
     if (this->_server != NULL) {
         result = this->_client->beginPacket(this->_server, this->_port);
     } else {
         result = this->_client->beginPacket(this->_ip, this->_port);
     }
 
-    if (result != 1) {
-        this->_client->stop();
+    if (result != 1)
         return false;
-    }
 
     this->_client->print('<');
     this->_client->print(pri);
@@ -199,8 +193,6 @@ inline bool Syslog::_sendLog(uint16_t pri, const char *appName, const char *mess
     this->_client->print(message);
     this->_client->endPacket();
 
-    this->_client->stop(); // W5100S: release UDP socket for other services
-
     return true;
 }
 

src/DisplayFormatters.cpp

@@ -4,8 +4,7 @@ const char *DisplayFormatters::getModemPresetDisplayName(meshtastic_Config_LoRaC
                                                          bool usePreset)
 {
 
-    // If use_preset is false, always return "Custom" — callers such as RadioInterface and Channels
-    // rely on this being a stable literal for channel-name hashing and default-channel detection.
+    // If use_preset is false, always return "Custom"
     if (!usePreset) {
         return "Custom";
     }

src/Power.cpp

@@ -35,11 +35,6 @@
 #include "nrfx_power.h"
 #endif
 
-#if defined(ARCH_NRF52)
-#include "Nrf52SaadcLock.h"
-#include "concurrency/LockGuard.h"
-#endif
-
 #if defined(DEBUG_HEAP_MQTT) && !MESHTASTIC_EXCLUDE_MQTT
 #include "mqtt/MQTT.h"
 #include "target_specific.h"
@@ -333,9 +328,6 @@ class AnalogBatteryLevel : public HasBatteryLevel
             scaled = esp_adc_cal_raw_to_voltage(raw, adc_characs);
             scaled *= operativeAdcMultiplier;
 #else // block for all other platforms
-#ifdef ARCH_NRF52
-            concurrency::LockGuard saadcGuard(concurrency::nrf52SaadcLock);
-#endif
             for (uint32_t i = 0; i < BATTERY_SENSE_SAMPLES; i++) {
                 raw += analogRead(BATTERY_PIN);
             }

src/RedirectablePrint.cpp

@@ -137,7 +137,7 @@ void RedirectablePrint::log_to_serial(const char *logLevel, const char *format,
         if (color) {
             ::printf("\u001b[0m");
         }
-        ::printf("| %02d:%02d:%02d %u.%03u ", hour, min, sec, millis() / 1000, millis() % 1000);
+        ::printf("| %02d:%02d:%02d %u ", hour, min, sec, millis() / 1000);
 #else
         printf("%s ", logLevel);
         if (color) {
@@ -151,7 +151,7 @@ void RedirectablePrint::log_to_serial(const char *logLevel, const char *format,
         if (color) {
             ::printf("\u001b[0m");
         }
-        ::printf("| ??:??:?? %u.%03u ", millis() / 1000, millis() % 1000);
+        ::printf("| ??:??:?? %u ", millis() / 1000);
 #else
         printf("%s ", logLevel);
         if (color) {

src/buzz/buzz.cpp

@@ -6,11 +6,6 @@
 #include "Tone.h"
 #endif
 
-#if defined(HAS_I2S)
-#include "main.h"
-#include <unordered_map>
-#endif
-
 #if !defined(ARCH_PORTDUINO)
 extern "C" void delay(uint32_t dwMs);
 #endif
@@ -55,50 +50,6 @@ const int DURATION_1_2 = 500;  // 1/2 note
 const int DURATION_3_4 = 750;  // 3/4 note
 const int DURATION_1_1 = 1000; // 1/1 note
 
-#ifdef HAS_I2S
-void playTonesRTTTL(const ToneDuration *tone_durations, int size)
-{
-    // translate ToneDuration[] to RTTTL string and play using audioThread
-    static std::unordered_map<int, std::string> freqToNote = {
-        {NOTE_C3, "c4"},   {NOTE_CS3, "c#4"}, {NOTE_D3, "d4"},   {NOTE_DS3, "d#4"}, {NOTE_E3, "e4"},   {NOTE_F3, "f4"},
-        {NOTE_FS3, "f#4"}, {NOTE_G3, "g4"},   {NOTE_GS3, "g#4"}, {NOTE_A3, "a4"},   {NOTE_AS3, "a#4"}, {NOTE_B3, "b4"},
-        {NOTE_C4, "c5"},   {NOTE_E4, "e5"},   {NOTE_G4, "g5"},   {NOTE_A4, "a5"},   {NOTE_C5, "c6"},   {NOTE_E5, "e6"},
-        {NOTE_G5, "g6"},   {NOTE_F5, "f6"},   {NOTE_G6, "g7"},   {NOTE_E7, "e8"}};
-
-    char rtttl[128] = "tone:d=32,o=4,b=200:"; // default duration and octave
-    for (int i = 0; i < size; i++) {
-        const auto &td = tone_durations[i];
-        std::string note = "b4";
-        if (freqToNote.find(td.frequency_khz) != freqToNote.end()) {
-            note = freqToNote[td.frequency_khz];
-        }
-        int dur = 32; // default duration
-        if (td.duration_ms >= 1000)
-            dur = 1;
-        else if (td.duration_ms >= 500)
-            dur = 2;
-        else if (td.duration_ms >= 250)
-            dur = 4;
-        else if (td.duration_ms >= 125)
-            dur = 8;
-        else if (td.duration_ms >= 62)
-            dur = 16;
-        else
-            dur = 32;
-
-        char noteStr[64];
-        snprintf(noteStr, sizeof(noteStr), "%s,%d", note.c_str(), dur);
-        strncat(rtttl, noteStr, sizeof(rtttl) - strlen(rtttl) - 1);
-
-        audioThread->beginRttl(rtttl, strlen(rtttl));
-        while (audioThread->isPlaying()) {
-            delay(10);
-        }
-        return;
-    }
-}
-#endif
-
 void playTones(const ToneDuration *tone_durations, int size)
 {
     if (config.device.buzzer_mode == meshtastic_Config_DeviceConfig_BuzzerMode_DISABLED ||
@@ -106,13 +57,7 @@ void playTones(const ToneDuration *tone_durations, int size)
         // Buzzer is disabled or not set to system tones
         return;
     }
-#ifdef HAS_I2S
-    if (moduleConfig.external_notification.use_i2s_as_buzzer && audioThread) {
-        playTonesRTTTL(tone_durations, size);
-        return;
-    }
-#endif
-#if defined(PIN_BUZZER)
+#ifdef PIN_BUZZER
     if (!config.device.buzzer_gpio)
         config.device.buzzer_gpio = PIN_BUZZER;
 #endif

src/concurrency/BinarySemaphorePosix.cpp

@@ -1,85 +1,10 @@
 #include "concurrency/BinarySemaphorePosix.h"
 #include "configuration.h"
 
-#include <errno.h>
-#include <sys/time.h>
-
 #ifndef HAS_FREE_RTOS
 
 namespace concurrency
 {
-#ifdef ARCH_PORTDUINO
-
-BinarySemaphorePosix::BinarySemaphorePosix()
-{
-    if (pthread_mutex_init(&mutex, NULL) != 0) {
-        throw std::runtime_error("pthread_mutex_init failed");
-    }
-    if (pthread_cond_init(&cond, NULL) != 0) {
-        pthread_mutex_destroy(&mutex);
-        throw std::runtime_error("pthread_cond_init failed");
-    }
-    signaled = false;
-}
-
-BinarySemaphorePosix::~BinarySemaphorePosix()
-{
-    pthread_cond_destroy(&cond);
-    pthread_mutex_destroy(&mutex);
-}
-
-/**
- * Returns false if we timed out
- */
-bool BinarySemaphorePosix::take(uint32_t msec)
-{
-    pthread_mutex_lock(&mutex);
-
-    if (!signaled) {
-        struct timespec ts;
-        clock_gettime(CLOCK_REALTIME, &ts);
-
-        ts.tv_sec += msec / 1000;
-        ts.tv_nsec += (msec % 1000) * 1000000L;
-        if (ts.tv_nsec >= 1000000000L) {
-            ts.tv_sec += 1;
-            ts.tv_nsec -= 1000000000L;
-        }
-
-        while (!signaled) {
-            int rc = pthread_cond_timedwait(&cond, &mutex, &ts);
-            if (rc == ETIMEDOUT)
-                break;
-            if (rc != 0) {
-                // Some other error occurred
-                pthread_mutex_unlock(&mutex);
-                throw std::runtime_error("pthread_cond_timedwait failed: " + std::to_string(rc));
-            }
-        }
-    }
-
-    bool wasSignaled = signaled;
-    signaled = false; // consume the signal (binary semaphore)
-
-    pthread_mutex_unlock(&mutex);
-    return wasSignaled;
-}
-
-void BinarySemaphorePosix::give()
-{
-    pthread_mutex_lock(&mutex);
-    signaled = true;
-    pthread_cond_signal(&cond);
-    pthread_mutex_unlock(&mutex);
-}
-
-IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken)
-{
-    give();
-    if (pxHigherPriorityTaskWoken)
-        *pxHigherPriorityTaskWoken = true;
-}
-#else
 
 BinarySemaphorePosix::BinarySemaphorePosix() {}
 
@@ -97,8 +22,7 @@ bool BinarySemaphorePosix::take(uint32_t msec)
 void BinarySemaphorePosix::give() {}
 
 IRAM_ATTR void BinarySemaphorePosix::giveFromISR(BaseType_t *pxHigherPriorityTaskWoken) {}
-#endif
 
 } // namespace concurrency
 
-#endif
+#endif

src/concurrency/BinarySemaphorePosix.h

@@ -2,10 +2,6 @@
 
 #include "../freertosinc.h"
 
-#ifdef ARCH_PORTDUINO
-#include <pthread.h>
-#endif
-
 namespace concurrency
 {
 
@@ -13,12 +9,7 @@ namespace concurrency
 
 class BinarySemaphorePosix
 {
-
-#ifdef ARCH_PORTDUINO
-    pthread_mutex_t mutex;
-    pthread_cond_t cond;
-    bool signaled;
-#endif
+    // SemaphoreHandle_t semaphore;
 
   public:
     BinarySemaphorePosix();
@@ -36,4 +27,4 @@ class BinarySemaphorePosix
 
 #endif
 
-} // namespace concurrency
+} // namespace concurrency

src/configuration.h

@@ -156,19 +156,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #ifdef USE_KCT8103L_PA
 // Power Amps are often non-linear, so we can use an array of values for the power curve
-#if defined(HELTEC_WIRELESS_TRACKER_V2)
 #define NUM_PA_POINTS 22
 #define TX_GAIN_LORA 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 13, 13, 13, 12, 12, 11, 10, 9, 8, 7
-#elif defined(HELTEC_MESH_NODE_T096)
-#define NUM_PA_POINTS 22
-#define TX_GAIN_LORA 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 14, 13, 13, 13, 12, 11, 10, 9, 8, 7
-#else
-// If a board enables USE_KCT8103L_PA but does not match a known variant and has
-// not already provided a PA curve, fail at compile time to avoid unsafe defaults.
-#if !defined(NUM_PA_POINTS) || !defined(TX_GAIN_LORA)
-#error "USE_KCT8103L_PA is defined, but no PA gain curve (NUM_PA_POINTS / TX_GAIN_LORA) is configured for this board."
-#endif
-#endif
 #endif
 
 #ifdef RAK13302
@@ -231,7 +220,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define BME_ADDR 0x76
 #define BME_ADDR_ALTERNATE 0x77
 #define MCP9808_ADDR 0x18
-#define INA_ADDR 0x40 // same as SHT2X
+#define INA_ADDR 0x40
 #define INA_ADDR_ALTERNATE 0x41
 #define INA_ADDR_WAVESHARE_UPS 0x43
 #define INA3221_ADDR 0x42
@@ -244,8 +233,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define LPS22HB_ADDR 0x5C
 #define LPS22HB_ADDR_ALT 0x5D
 #define SFA30_ADDR 0x5D
-#define SHTXX_ADDR 0x44
-#define SHTXX_ADDR_ALT 0x45
+#define SHT31_4x_ADDR 0x44
+#define SHT31_4x_ADDR_ALT 0x45
 #define PMSA003I_ADDR 0x12
 #define QMA6100P_ADDR 0x12
 #define AHT10_ADDR 0x38

src/detect/ScanI2C.cpp

@@ -37,8 +37,9 @@ ScanI2C::FoundDevice ScanI2C::firstKeyboard() const
 
 ScanI2C::FoundDevice ScanI2C::firstAccelerometer() const
 {
-    ScanI2C::DeviceType types[] = {MPU6050, LIS3DH, BMA423, LSM6DS3, BMX160, STK8BAXX, ICM20948, QMA6100P, BMM150, BMI270};
-    return firstOfOrNONE(10, types);
+    ScanI2C::DeviceType types[] = {MPU6050,  LIS3DH,   BMA423,   LSM6DS3, LSM6DSOX, BMX160,
+                                   STK8BAXX, ICM20948, QMA6100P, BMM150,  BMI270};
+    return firstOfOrNONE(11, types);
 }
 
 ScanI2C::FoundDevice ScanI2C::firstAQI() const

src/detect/ScanI2C.h

@@ -31,6 +31,9 @@ class ScanI2C
         INA3221,
         MAX17048,
         MCP9808,
+        SHT31,
+        SHT4X,
+        SHTC3,
         LPS22HB,
         QMC6310U,
         QMC6310N,
@@ -44,6 +47,7 @@ class ScanI2C
         BMA423,
         BQ24295,
         LSM6DS3,
+        LSM6DSOX,
         TCA9535,
         TCA9555,
         VEML7700,
@@ -91,8 +95,7 @@ class ScanI2C
         SFA30,
         CW2015,
         SCD30,
-        ADS1115,
-        SHTXX
+        ADS1115
     } DeviceType;
 
     // typedef uint8_t DeviceAddress;

src/detect/ScanI2CTwoWire.cpp

@@ -136,9 +136,7 @@ bool ScanI2CTwoWire::i2cCommandResponseLength(ScanI2C::DeviceAddress addr, uint1
     return match;
 }
 
-#if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR
-// FIXME Move to a separate file for detection of sensors that require more complex interactions?
-// For SEN5X detection
+/// for SEN5X detection
 // Note, this code needs to be called before setting the I2C bus speed
 // for the screen at high speed. The speed needs to be at 100kHz, otherwise
 // detection will not work
@@ -176,46 +174,6 @@ String readSEN5xProductName(TwoWire *i2cBus, uint8_t address)
 
     return String(productName);
 }
-#endif
-
-#if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR
-bool detectSHT21SerialNumber(TwoWire *i2cBus, uint8_t address)
-{
-
-    i2cBus->beginTransmission(address);
-    i2cBus->write(0xFA);
-    i2cBus->write(0x0F);
-
-    if (i2cBus->endTransmission() != 0)
-        return false;
-
-    if (i2cBus->requestFrom(address, (uint8_t)8) != 8)
-        return false;
-
-    // Just flush the data
-    while (i2cBus->available() < 8) {
-        i2cBus->read();
-    }
-
-    i2cBus->beginTransmission(address);
-    i2cBus->write(0xFC);
-    i2cBus->write(0xC9);
-
-    if (i2cBus->endTransmission() != 0)
-        return false;
-
-    if (i2cBus->requestFrom(address, (uint8_t)6) != 6)
-        return false;
-
-    // Just flush the data
-    while (i2cBus->available() < 6) {
-        i2cBus->read();
-    }
-
-    // Assume we detect the SHT21 if something came back from the request
-    return true;
-}
-#endif
 
 #define SCAN_SIMPLE_CASE(ADDR, T, ...)                                                                                           \
     case ADDR:                                                                                                                   \
@@ -413,7 +371,7 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                 break;
 #endif
 #if !defined(M5STACK_UNITC6L)
-            case INA_ADDR: // Same as SHT2X
+            case INA_ADDR:
             case INA_ADDR_ALTERNATE:
             case INA_ADDR_WAVESHARE_UPS:
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFE), 2);
@@ -429,12 +387,7 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                         logFoundDevice("INA260", (uint8_t)addr.address);
                         type = INA260;
                     }
-#if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR
-                } else if (detectSHT21SerialNumber(i2cBus, (uint8_t)addr.address)) {
-                    logFoundDevice("SHTXX (SHT2X)", (uint8_t)addr.address);
-                    type = SHTXX;
-#endif
-                } else { // Assume INA219 if none of the above ones are found
+                } else { // Assume INA219 if INA260 ID is not found
                     logFoundDevice("INA219", (uint8_t)addr.address);
                     type = INA219;
                 }
@@ -495,19 +448,22 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                     }
                     break;
                 }
-            case SHTXX_ADDR:     // same as OPT3001_ADDR_ALT
-            case SHTXX_ADDR_ALT: // same as OPT3001_ADDR
+            case SHT31_4x_ADDR:     // same as OPT3001_ADDR_ALT
+            case SHT31_4x_ADDR_ALT: // same as OPT3001_ADDR
                 if (getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x7E), 2) == 0x5449) {
                     type = OPT3001;
                     logFoundDevice("OPT3001", (uint8_t)addr.address);
-                } else { // SHTXX
-                    type = SHTXX;
-                    logFoundDevice("SHTXX", (uint8_t)addr.address);
+                } else if (i2cCommandResponseLength(addr, 0x89, 6)) { // SHT4x serial number (6 bytes inc. CRC)
+                    type = SHT4X;
+                    logFoundDevice("SHT4X", (uint8_t)addr.address);
+                } else {
+                    type = SHT31;
+                    logFoundDevice("SHT31", (uint8_t)addr.address);
                 }
 
                 break;
 
-                SCAN_SIMPLE_CASE(SHTC3_ADDR, SHTXX, "SHTXX", (uint8_t)addr.address)
+                SCAN_SIMPLE_CASE(SHTC3_ADDR, SHTC3, "SHTC3", (uint8_t)addr.address)
             case RCWL9620_ADDR:
                 // get MAX30102 PARTID
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xFF), 1);
@@ -555,6 +511,9 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                 if (registerValue == 0x6A) {
                     type = LSM6DS3;
                     logFoundDevice("LSM6DS3", (uint8_t)addr.address);
+                } else if (registerValue == 0x6C) {
+                    type = LSM6DSOX;
+                    logFoundDevice("LSM6DSOX", (uint8_t)addr.address);
                 } else {
                     type = QMI8658;
                     logFoundDevice("QMI8658", (uint8_t)addr.address);
@@ -592,7 +551,19 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
 
                 break;
 
-                SCAN_SIMPLE_CASE(LSM6DS3_ADDR, LSM6DS3, "LSM6DS3", (uint8_t)addr.address);
+            case LSM6DS3_ADDR:
+                registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x0F), 1);
+                if (registerValue == 0x6A) {
+                    type = LSM6DS3;
+                    logFoundDevice("LSM6DS3", (uint8_t)addr.address);
+                } else if (registerValue == 0x6C) {
+                    type = LSM6DSOX;
+                    logFoundDevice("LSM6DSOX", (uint8_t)addr.address);
+                } else {
+                    type = QMI8658;
+                    logFoundDevice("QMI8658", (uint8_t)addr.address);
+                }
+                break;
                 SCAN_SIMPLE_CASE(VEML7700_ADDR, VEML7700, "VEML7700", (uint8_t)addr.address);
             case TCA9555_ADDR:
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x01), 1);
@@ -719,7 +690,6 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                     logFoundDevice("BMX160", (uint8_t)addr.address);
                     break;
                 } else {
-#if HAS_TELEMETRY && !MESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR
                     String prod = "";
                     prod = readSEN5xProductName(i2cBus, addr.address);
                     if (prod.startsWith("SEN55")) {
@@ -735,7 +705,6 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                         logFoundDevice("Sensirion SEN50", addr.address);
                         break;
                     }
-#endif
                     if (addr.address == BMX160_ADDR) {
                         type = BMX160;
                         logFoundDevice("BMX160", (uint8_t)addr.address);